User's Manual

ManualsBrandsWoori Technology ManualsAV receiversAV RECEIVER

OTE:

hile these tests detect whether a speaker is

onnected to a particular output, they cannot deter-

mine whether the speaker is in the correct position.

(For example, it can tell whether a speaker is connected

to the Surround Right output, but it cannot tell whether

he speaker is on the right or left side of your listening

room.) For that reason, we strongly recommend that

you try to listen carefully to make sure that the test

tone circulates in a clockwise rotation, starting with the

ront left speaker, to the center, to the front right, and

o on to the subwoofer. If the tone is heard from a

speaker that seems as though it is out of sequence,

such as the tone coming from the surround left speaker

when the next speaker in the sequence should be the

surround right speaker, exit the EzSet/EQ system when

the test sequence is completed and use the manual

output level tone adjustment process, as outlined on

page 37, to determine which, if any, speaker is incor-

rectly connected.

When the Far Field tests are complete, a message

screen will appear to indicate whether the procedure

was successful or not. In most cases, there will not be

any problems and you will see the message shown in

Figure 15 on your screen.

Figure 15

If the speaker positions shown match the actual

speaker layout in your system, confirm that the

cursor is pointing to

CONTINUE TO NEAR

FIELD

and press the OK/Enter Button E on

the TC 30 or the

Set Button

to take the Near

Field measurements in Step 2.

If the measurements are not successful, due to a

missing or malfunctioning speaker,

ERROR

message will appear as shown in Figure 16. EzSet/EQ

is programmed to look for speaker pairs at the front

left/ front right, surround left/surround right and sur-

round back left/surround back right positions. If the

test results indicate that one

, but not both, of the

speakers in any of these pairs is present,

the menu

will show

NO next to the speaker position where the

tests did not report back that a speaker is present.

Should this message appear

make note of the sus

pect speaker location, exit the menus and turn the

receiver off. Check all speaker wire connections and

then rerun EzSet/EQ.

Figure 16

n some cases, the system may not function properly

due to overly high output levels. When this occurs, you

will see the message shown in Figure 17.

Figure 17

If the EQ DESIGN OVERLOAD message

appears, first press the

OK/Enter Button E on the

TC 30 or the

Set Button

on the ZR 10 remote.

This will take you back to the

EQ DESIGN

SETP 1 ERROR

menu. Make certain that the

cursor is pointing to

REPEAT TEST and press

the

OK/Enter Button E on the TC 30 or the Set

Button

on the ZR 10 remote again. At the

EZSET DESIGN STEP 1 menu, lower the

volume by at least 6dB and follow the steps described

above to run the EzSet/EQ system again. Depending

on the amount of the overload, you may need to

repeat the process more than once to achieve

satisfactory results.

Step 2. When the Far Field measurements are com-

pleted, the next step is to take the Near Field meas-

urements. These measurements enable EzSet/EQ to

produce the most accurate settings for high-frequency

equalization. The Near Field measurements are similar

to the Far Field tests, except that the system will “listen”

to only one speaker at a time

rather than sending the

test signals to all speakers in rotation.

Figure 18

When it first appears, the NEAR FIELD

MENU (Figure 18) will show a list of all the possible

peakers and

ext to each speaker position

where the Far Field measurements detected a speaker

he Near Field measurements should be made for

each of those speakers to create a successful

Q Design. To select a speaker position for measure-

ment, press the

⁄/¤ Navigation Buttons

to move the cursor next to the desired

speaker position and then press the

OK/Enter Button

E on the TC 30 or the Set Button

on the

ZR 10 remote.

Before the test begins, an informational message will

appear (Figure 19).

Figure 19

Follow the instructions and place the microphone

about halfway between the speaker and the listening

position where the microphone was placed during the

Far Field measurements. With the cursor pointing to

CONTINUE, press the OK/Enter Button E

on the TC 30 or the Set Button

on the ZR 10

remote control.

When the

WARNING message appears, press

the

› Navigation Button D

to start the test.

A short tone will be heard from the speaker being

tested, and after a short pause the on-screen menu

will show a message to inform you of whether the test

was successful or not.

• If the test was successful and there are more

speaker positions for which a Near Field measure-

ment is required, press the

OK/Enter Button E

on the TC 30 or the Set Button

on the

ZR 10 remote to return to the

NEAR FIELD

. Speaker positions where the Near Field

measurement has been completed will show

DONE to the right of the position name

Press the

⁄/¤ Navigation Buttons D

to select a

position where

NO still appears and repeat the

steps shown above until a Near Field measurement

has been taken at all speaker positions

• If the test was successful and all Near Field meas-

urements have been completed,

the on-screen

message will direct you to the

Subwoofer

measure-

ments. Make certain that the cursor is pointing to

CONTINUE TO SUB DESIGN and

press the

OK/Enter Button E on the

TC 30

the

Set Button

on the ZR 10 remote (unless

EZSET DESIGN STEP 2

ut mic 2ft/0.6m from

selected speaker,

pointing at it, in a

direct path between

the listening position

and the speaker.

CONTINUE

BACK TO EZSET/EQ MAIN

→→

* NEAR FIELD MENU *

Please select a speaker:

1-LEFT FRONT : NO

2-CENTER FRONT : NO

3-RIGHT FRONT : NO

4-LEFT SURR : NO

5-RIGHT SURR : NO

6-LEFT BACK SURR : ---

7-RIGHT BACK SURR: ---

SKIP NEAR FIELD DESIGN

BACK TO EZSET/EQ MAIN

→→

EQ DESIGN OVERLOAD

Overload found. Check

microphone placement.

Reduce volume by 6dB

and run EZSET/EQ again.

CONTINUE

→→

* EQ DESIGN STEP 1 ERROR*

Detected speaker config

FL : YES SBR: YES

CEN : YES SBL: YES

FR : YES SL : YES

SR : NO

Verify spkr cons, mic

Position. Raise vol 5dB.

REPEAT TEST

BACK TO EZSET/EQ MAIN

→→

* DESIGN STEP 1 RESULTS*

STEP 1 successful

Detected speaker config

FL : YES SBR: YES

CEN : YES SBL: YES

FR : YES SL : YES

SR : YES

ONTINUE TO NEAR FIELD

SKIP NEAR FIELD DESIGN

BACK TO EZSET/EQ MAIN

→→

SYSTEM CONFIGURATIONSYSTEM CONFIGURATION

SYSTEM CONFIGURATION 33SYSTEM CONFIGURATION 33