User's Manual

Voltage Trigger (Curtain)

The Trigger Out [circle 38] on the AVR rear panel can be controlled in two modes:

AVR ON/OFF: Simply put, when the AVR turns ON, the Trigger Out [circle 38] outputs a

constant +12VDC control voltage. In this case with the Trigger Out [circle 38] being used to

open a curtain, the curtain will open as soon as the AVR is turned ON. When the AVR is turned

OFF, the Trigger Out [circle 38] drops to 0 VDC, and the curtain closes. NOTE: If the AVR turns

on to Multiroom Mode, the Trigger Out [circle 38] will stay at 0VDC until the Main Room is

turned ON.

MANUAL VIA REMOTE: In this mode, the Trigger Out Jack [circle 38] is controlled with the

Trigger Button [oval 50] on the AVR21ENR1 remote. When the AVR is turned ON, the Trigger

Out has an output of 0VDC. When the Trigger Button [oval 50] on the remote is pressed, the

Trigger Out goes to +12VDC, in this case to drop a screen. Press the Trigger Button [oval 50]

again, the voltage is cut and the screen retracts.

To configure the AVR21EN Trigger Out Jack [circle 38] to open a curtain when the Main Room

is turned ON:

Press the Menu Button on the remote to bring the MAIN MENU to the screen. Press the ▼/▲

Navigation Button [oval 16] so that the cursor is pointed to the REMOTE CONTROL SETUP line.

Press the Set Button [oval 18]. The REMOTE CNTL SETUP 1 screen will appear. Press the

▼/▲ Navigation Button [oval 16] so that the cursor is pointed to GO TO REMOTE CNTL 2.

Press the Set Button [oval 18]. The REMOTE CNTL SETUP 2 screen will appear.

Press the ▼/▲ Navigation Button [oval 16] so that the cursor is pointed to the ASSIGN

TRIGGER OUT line. Press the ◄/► Navigation Button [oval 16] until SCRN appears. Press the

▼/▲ Navigation Button [oval 16] so that the cursor is pointed to

CURTAIN CONTROL. Press

the Set Button [oval 18]. Press the ▼/▲ Navigation Button [oval 16] so that the cursor is

pointed to the CONTROL line. Press the ◄/► Navigation Button [oval 16] to select the preferred

mode. Press ▼/▲ Navigation Button [oval 16] so that the cursor is pointed to the BACK TO

REM CNTL SETUP line. Press the Set Button [oval 18].

To test the CURTAIN OPEN/CLOSE commands with AVR ON/OFF, turn the AVR OFF and

manually close the curtain. To test ON, either: press the Standby/ON Button [square 2] on the

AVR front panel; or press the ON Button [oval 2] on the AVR21ENR1 remote. The AVR should

turn ON and the curtain should open.

To test OFF, either: press the Standby/ON Button [square 2] on the AVR front panel; or: press

the OFF Button on the AVR21ENR1 remote. The AVR should turn OFF and the curtain should

close.

To test the CURTAIN OPEN/CLOSE commands with MANUAL VIA REMOTE, turn the AVR OFF

and manually close the curtain. Turn the AVR ON by pressing the Standby/ON Button [square

2] on the AVR front panel or press the ON Button [oval 2] on the remote. (The AVR should be

on, but the curtain should still be closed.) Press the Trigger Button [oval 50] on the remote. The

curtain should open. Press the Trigger Button [oval 50] again and the curtain should close.

Exit Setup

If no further programming is required, press the AVR Button [oval 5] on the AVR21ENR1 remote

and then the Exit Button [oval 17] to return to normal operation mode.