Rev. 9/16/2005 MAN0161 RB990-2 RB1010-2 Tested. Proven. Unbeatable.
TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration included with the Operator’s Manual. The customer must sign the registration which certifies that all Dealer Check List items have been completed.
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RB990-2 & RB1010-2 SPECIFICATIONS MODEL RB990-2 RB1010-2 Blade Width 9 ft. (2743 mm) 10 ft. (3048 mm) Tractor hp Requirement 150 hp Maximum (112 kw) 150 hp Maximum (112 kw) Tractor Hydraulic System Pressure 3000 psi Maximum (20.68 MPa) 3000 psi Maximum (20.68 MPa) Weight (Hydraulic) 1519 lbs. (688 kg) 1569 lbs. (711kg) Weight (Manual) 1487 lbs. (673 kg) 1535 lbs. (697 kg) Blade Position - Mechanical . . . . . .
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Always comply with all state and local lighting and marking requirements. Never allow riders on power unit or attachment. Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! STORAGE Secure equipment parking stand(s) in park position before detaching. Keep children and bystanders away from storage area. RB990/1010 SR (Rev.
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 3 2 2 3 4 7 5 2 6 7 2 8 1 CD6054A 6 MODEL NO. SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. 1 - Serial Number Plate 2 - PN 19924 WARNING HIGH-PRESSURE HYDRAULIC OIL LEAKS CAN PENETRATE SKIN RESULTING IN SERIOUS INJURY, GANGRENE OR DEATH. n Check for leaks with cardboard; never use hand. n Before loosening fittings: lower load, release pressure, and be sure oil is cool.
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 3 - PN 1002941 4 - PN 1004250 5 - PN 1004299 WARNING WARNING TO AVOID SERIOUS INJURY OR DEATH: WARNING Read Operator's Manual CRUSHING AND PINCHING HAZARD Be extremely careful handling various parts of the machine. They are heavy and hands, fingers, feet, and other body parts could be crushed or pinched between tractor and implement.
OPERATION WARNING Never allow children or untrained persons to operate equipment. Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment. Never allow riders on power unit or attachment. Keep all persons away from operator control area while performing adjustments, service, or maintenance. Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or other body parts to check for leaks. Wear safety goggles.
become entrapped during adjustment changes or if the 3-point hitch suddenly lowers. CAUTION NOTE: The blade can be set to any angle from 0 to 60 degrees, right or left. In some cases it may be necessary to offset to the right and tip up the right end of the blade to rotate it. Always secure lock pins with safety pins to prevent lock pins from bumping out of the positioning holes. Failure to do so may result in accidents and/or damage to blade.
boom to rotate 30 degrees to the right or left with a maximum blade offset of 33 inches (838 mm). To offset the blade: 1. Park the tractor on level ground. 10 2. Apply parking brake and raise blade 2" (51 mm) above the ground. 3. Shut off the engine and level the boom. 4. Remove rivet pin (59), swing the boom to the desired position, and replace the pins. IMPORTANT Rivet pin (59) is designed to shear at a predetermined load to prevent damage to the blade.
PRE-OPERATION CHECK LIST (OPERATOR’S RESPONSIBILITY) ___ Review and follow all safety rules and safety decal instructions on pages 5 through 9. ___ Check that equipment is properly and securely attached to tractor. ___ Check that all safety decals are installed and in good condition. Replace if damaged. ___ Check that all hardware and cotter pins are properly installed and secured. PRE-OPERATION CHECK LIST (OPERATOR’S RESPONSIBILITY) ___ Check all lubrication points are greased.
OWNER SERVICE WARNING Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or other body parts to check for leaks. Wear safety goggles. Hydraulic fluid under pressure can easily penetrate skin and will cause serious injury or death. Make sure that all operating and service personnel know that if hydraulic fluid penetrates skin, it must be surgically removed as soon as possible by a doctor familiar with this form of injury or gangrene, serious injury, or death will result.
Periodically or Before Extended Storage ● Clean large debris such as clumps of dirt, grass, crop residue, etc. from machine. ● Remove the remainder using a low-pressure water spray. 1. Be careful when spraying near scratched or torn safety decals or near edges of decals as water spray can peel decal off surface. 2. Be careful when spraying near chipped or scratched paint as water spray can lift paint. 3. If a pressure washer is used, follow the advice of the pressure washer manufacturer.
ASSEMBLY WARNING CAUTION Before working underneath, read manual instructions, securely block up, and check stability. Secure blocking prevents equipment from dropping due to hydraulic leak down, hydraulic system failure, or mechanical component failure. Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head.
Attach Parking Stand 57 1. Attach the parking stand brackets (2) to bottom of A-Frame. Secure using four cap screws (55) and washers (57). 2. Install parking stand (3) between brackets. Secure with cap screw (56), lock nut (58), clevis pin (54), and two safety pins (30). 55 3 2 NOTE: Do not over tighten cap screw (56). Parking stand needs to pivot freely. 3. Remove A-Frame from crate. 2. 3. 30. 54. 55. 56. 57. 58. Bracket, Parking Stand Stand, Assembly Pin, Safety 3/16 Pin, Headless .50 x 3.
Attach Pivot Assembly to Moldboard Refer to Figure 9. 1” Board 1. Position moldboard approximately 8” (203 mm) from the edge of the crate base as shown. Stub Shaft 2. Place a 1” (25 mm) thick board under both front corners of moldboard as shown. 3. Using a lifting device, lift boom and pivot assembly and place pivot assembly over stub shaft on back of moldboard. 8” Spacing Figure 9 Pivot Assembly Positioned to Moldboard Refer to Figure 10. 4.
Attach A-Frame to Boom Assembly Refer to Figure 11. 1. Attach lifting device to boom assembly, just ahead of pivot tube. 2. Carefully lift boom off crate base and rotate 90 degrees to moldboard. DP6 Figure 11 Lift Boom Assembly off Crate Refer to Figure 12 and Figure 13. 3. Place a 5” (127 mm) block under pivot assembly to prevent blade assembly from rolling over backwards. 4. Place a stand 27” to 28” (685 to 711 mm) tall or heavy duty saw horse under the boom as shown.
Attach A-Frame to Boom Assembly (continued) 82 5. Place A-Frame (1) over end of boom assembly (4). 46 6. Insert washer(s) (83) between top of boom assembly and A-Frame. One or more washers may be needed to eliminate excessive movement between A-Frame and boom assembly. 70 32 7. Position angling hydraulic cylinder (13) in boom assembly. 8. Align holes in A-Frame, washers, boom assembly, and angling cylinder. 9. Insert pin (82) through assembly and secure with washer (83) and cotter pin (46). 10.
Install Angling Linkage 1. Insert two index pin assemblies (79) into angling crank (16). Secure with clinch pins (45). 83 2. Insert Spirol pin (38) into clevis pin (76). 38 3. Attach one end of connecting link (15) to angling crank (16) using clevis pin (76) and flat washer (80). Secure into position with cotter pin (31). 4. Install guide link (14) (previously removed) and washer(s) (83) to boom assembly (4). Secure with cotter pin (31). 31 13 80 77 31 6.
Install Manual Tube 7 49 1. Place manual tube (7) over holes on top of boom assembly as shown in Figure 17. 48 2. Secure into position using three cap screws (47), six flat washers (48), (one on each side), and lock nuts (49). 7. 47. 48. 49. Manual Storage Tube Screw, HHCS 3/8 NC x 1-1/4 GR5 Washer, Flat 3/8 Standard Nut, Lock 3/8 NC 48 CD6055-7 47 Figure 17 Manual Tube Installation Install Slow Moving Vehicle (SMV) Sign 34 Refer to Figure 18. 8 9 1.
Manual Configuration RB990MA-2 / RB1010MA-2 1. Attach ratchet (23) to moldboard (20) and pivot assembly (18) using pins supplied with ratchet. 2. Insert inner offset link (12) into outer offset link (11). 3. Attach outer offset link to bracket on A-Frame and insert clevis pin (78). Secure with Spirol pin (38), washer (80), and cotter pin (31). 4. Attach inner offset link to the boom assembly and insert clevis pin (77). Secure with Spirol pin (38), washer (80), and cotter pin (31). 78 5.
Install Angle Cylinder Hoses 1. Install adapter (2) into base end of angle cylinder (1). 2. Install adapter (3) into the rod end of angle cylinder (1). 4 3. Attach 96” hose (4) to adapter (2) and 108” hose (5) to adapter (3). 6 4. Wrap binding strap (7) around barrel of cylinder to secure 108” hose (5). 5. Install hose clamp (6) to A-Frame using cap screw (10) and lock nut (11). Do not tighten at this time. 5 DP9 6. Place hoses in clamp. Allow enough slack for hoses to move freely when cylinder moves.
Install Hydraulic Offset Kit 1004907 (Optional) 17 Refer to Figure 22 & Figure 23. 1. Remove inner and outer offset links if previously installed. 2. Attach the hydraulic offset cylinder (1) between the A-Frame and boom. Secure with pins and hardware removed with offset links. Install Relief Valves 1. Attach two double relief valves (3) to boom assembly. Secure with two cap screws (32), four flat washers (33), and lock nuts (34). DP10 Figure 22 Offset Kit Installed 2.
To Tractor Angle Couplers To Tractor Offset Couplers A C 3 D 20 B Relief Valves & Hose Connections 17 32 33 21 5 A 16 20 3 B 4 16 2 33 18 34 19 C 18 8 CD6067-1 19 D 16 1 18 18 Figure 23 1004907 Hydraulic Offset Kit Hose Installation 26 Assembly MAN0161 (Rev.
Install Selector Valve KIt 1004909 (Optional) Refer to Figure 24, Figure 26, & Figure 27. 1 NOTE: Rear blade must be equipped with hydraulic angling and offset relief valves to use this kit. 1. Remove hoses and straight connectors on the front side of relief valves if previously installed. 2 2. Install four 45-degree elbows (5) into relief valve ports. 3. Insert two cap screws (12) through mounting plate (3). 4. Attach selector valve (1) to valve mounting plate (3).
13 3 12 1 16 15 4 6 5 14 7 CD6059-1 8 9 Figure 26 Selector Valve Installation 1 2 A C B C Relief Valves CD6059-2 D B A D To Tractor Coupler Selector Valve Figure 27 Selector Valve Hose Connection 28 Assembly MAN0161 (Rev.
Install Hydraulic Tilt Kit 1004908 (Optional) 1. Remove ratchet if previously installed. 2. Attach hydraulic cylinder (1) to pivot assembly and moldboard as shown. Secure with pins supplied with the cylinder. 3. Install two elbows (4) into ports of tilt cylinder as shown. 4. Remove caps (3) from end of hydraulic tube assemblies (2) at the end of boom. 5. Attach 45” hoses (5) to hydraulic tube assembly and elbows (4) in hydraulic cylinder. 6. Secure hoses together with binding strap (7). 7.
Hydraulic Configuration RB990H-2 / RB1010H-2 CD6056-2 30 Assembly MAN0161 (Rev.
Install Hydraulic Offset Cylinder & Relief Valves 17 Refer to Figure 30 & Figure 31. 1. Attach the hydraulic offset cylinder (1) between the A-Frame and boom. Secure with pins (77 & 78), two Spirol pins (38), washers (80), and cotter pins (31). See Figure 31 for locations. Install Relief Valves 1. Attach two double relief valves (3) to boom assembly. Secure with two cap screws (32) four flat washers (33), and lock nuts (34). DP10 2. Install elbow (17) in top port (A) of inner relief valve.
To Tractor Angle Couplers Relief Valves & Hose Connections To Tractor Offset Couplers A C 17 3 D 20 B 32 5 33 22 B 16 3 A 9 20 16 2 33 18 34 19 18 19 38 16 C 1 38 CD6067-2 77 18 78 D 80 18 31 31 80 Figure 31 Hydraulic Offset Cylinder and Relief Valves Installation 32 Assembly MAN0161 (Rev.
Install Tilt Cylinder 1. Attach hydraulic cylinder (3) to pivot assembly and moldboard as shown. Secure with pins supplied with the cylinder. 2. Install two elbows (17) into ports of tilt cylinder as shown. 3. Remove caps (15) from end of hydraulic tube assemblies (5) at the end of boom. 4. Attach 45” hoses (21) to hydraulic tube assembly and elbows (17) in hydraulic cylinder. 5. Secure hoses together with binding strap (9). 6. Remove caps (15) from tube assemblies at the front of boom. 7.
Install Pneumatic Tail Wheel Kit 29399 (Optional) IMPORTANT ■ When grading with tail wheel attached, do not attach upper link of tractor 3-point hitch to blade without using floating links (17 & 18). Without floating links, equipment damage may result and void warranty. ■ Do not use this pneumatic tail wheel kit with 3-point quick hitch. Refer to Figure 34. The tail wheel is very helpful for finish grading and leveling work. Set approximate grading height with ratchet (12).
Figure 34 Pneumatic Tail Wheel Installation 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Tail wheel, Pneumatic complete Tire, Wheel & Hub Wheel Yoke Assembly Pin, Spirol 7/16 x 2-1/2 Disc, Friction 4 x 6.15 Plate, Top Dampener Grease Fitting, 1/8 Pipe Thread Bushing, Bronze 1.5 x 1.63 x 1.50 O-Ring .09 x 1.56 OD Cap, Dust Tail Wheel Arm Assembly Ratchet Tail Wheel Bracket Assembly MAN0161 (Rev. 9/16/2005) 14. 15. 16. 17. 18 19. 21. 22. 23. 24. 25. 26. 27.
PRE-DELIVERY CHECK LIST (DEALER’S RESPONSIBILITY) DELIVERY CHECK LIST (DEALER’S RESPONSIBILITY) Inspect the equipment thoroughly after assembly to ensure it is set up properly before delivering it to the customer. ___ Show customer how to make adjustments. The following check lists are a reminder of points to inspect. Check off each item as it is found satisfactory or after proper adjustment is made. ___ Check that all safety decals are installed and in good condition. Replace if damaged.
PARTS INDEX REAR BLADES RB990MA-2 RB1010MA-2 RB990H-2 RB1010H-2 RB990-2 / RB1010-2 MAIN ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 RB990-2 / RB1010-2 MAIN ASSEMBLY PARTS LIST . . . . . . . . . . . . . . . . 39 RB990MA-2 / RB1010MA-2 ANGLE CYLINDER (MAIN ASSEMBLY) . . . . 40 HYDRAULIC TILT KIT 1004908 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 RB990H-2 /RB1010H-2 HYDRAULIC CONFIGURATION . . . . . . . . . . . . . .
RB990-2 / RB1010-2 MAIN ASSEMBLY 82 46 70 74 38 7 80 32 73 78 34 49 48 8 30 10 83 As Req. 41 1 58 2 59 31 73 72 11 33 69 53 9 83 57 55 40 56 5 30 3 31 48 49 48 38 31 77 80 83 As Required 38 31 4 14 77 47 80 13 12 39 54 38 CD6055-A 6 31 76 80 62 17 79 15 16 45 23 20 22 64 60 21 65 18 19 61 62 66 24 - Decal Set, Safety RB990/1010 25 - Decal Set, Complete RB990/1010 38 Parts MAN0161 (Rev.
RB990-2 / RB1010-2 MAIN ASSEMBLY PARTS LIST REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1005013 1 A-Frame 40 4378 2* 5/16 Flat washer, standard 2 26099 2 Parking stand bracket 41 6778 8* 5/16 NC Nut Lock 3 26095 1 Parking stand 45 3282 4 1005014 1 Boom assembly 46 5 1004262 1 Bracket - SMV Sign 47 6 62484 1 Socket SMV Emblem 7 1003828 1 Manual Tube 48 8 1004251 1 SMV Bracket 49 9 24611 1 SMV Sign 53 27542 4 7/16 x 2 Klik Pin 10 1005016 1
RB990MA-2 / RB1010MA-2 ANGLE CYLINDER (MAIN ASSEMBLY) 10 4 2 5 6 11 CD6041 3 1 7 REF PART QTY DESCRIPTION 1 1005015 1 Hyd Cylinder 4 x 30 2 315049 1 3/4 JICF 3/4 ORBM adapter 3 61 1 3/4 JICM 3/4 ORBM adapter 4 360166 1 Hose, 3/8 96 1/2 NPTM 3/4 JICM 5 1004856 1 Hose, 3/8 108 1/2 NPTM 3/4 JICF 56 1 Feedline Hose Clamp- 5/8 6 7 65766 4* 34” Binding Strap 10 6096 1* 5/16 NC x 3/4 Hex head cap screw GR5 11 6778 1* 5/16 NC Lock nut * Standard Hardware; Obtain Locally 40
HYDRAULIC TILT KIT 1004908 (OPTIONAL) 6 3 2 5 4 1 7 CD6066 REF QTY DESCRIPTION 1 1003197 1 Hyd Cylinder 3.5 x 1.25 x 10.0 2† 1003192 2 Tube Assembly - Rear Blade 3† 1004844 4 Cap, 3/4 JICF (for shipping only) 4 316004 2 Elbow, 3/4 ORBM 3/4 JICM 90 5 1004854 2 Hose, 3/8 45 3/4 JICF 3/4 JICF 6 1004283 2 Hose, 3/8 66 1/2 NPTM 3/4 JICF 7 MAN0161 (Rev.
RB990H-2 / RB1010H-2 HYDRAULIC CONFIGURATION 6 8 To Tractor Angle Couplers 33 To Tractor Offset Couplers 31 A C 4 D B 30 7 34 5 7 34 17 20 10 16 A 32 B 33 22 4 33 2 22 34 19 18 D 1 15 34 C 18 17 5 9 21 17 3 CD6056 42 Parts MAN0161 (Rev.
RB990H-2 / RB1010H-2 HYDRAULIC CONFIGURATION PARTS LIST REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1005016 1 Hyd Cylinder 4.00 x 2.00 x 16.00 19 360160 1 Hose, 3/8 30 3/4 ORBM 3/4 JICF 2 1005015 1 Hyd Cylinder 4.00 x 2.00 x 30.00 20 1004855 1 Hose, 3/8 40 3/4 ORBM 3/4 JICF 3 1003197 1 Hyd Cylinder 3.5 x 1.25 x 10.
HYDRAULIC OFFSET KIT 1004907 (OPTIONAL) REF PART QTY DESCRIPTION 1 1005016 1 Hyd Cylinder 4.00 x 2.00 x 16.00 2 1005015 1 Hyd Cylinder 4.00 x 2.00 x 30.
SELECTOR VALVE KIT 1004909 (OPTIONAL) 13 3 12 1 16 15 4 6 5 14 7 CD6059-1 8 9 1 2 B A C B C REF PART Selector Valve D QTY DESCRIPTION To Tractor Coupler D Relief Valves CD6059-2 A REF PART QTY DESCRIPTION 1 1004261 1 Valve, Hyd Double Selector 12 14562 2* 5/16 NC x 1 Cap screw GR5 2† 1004260 2 Valve, Hyd Double Relief 1600 psi 13 14139 3 26105 1 Valve mounting bracket 14 7747 1* 3/8 NC x 3 Cap screw GR5 4 316017 4 Adapter, 3/4 JICM 1-1/16 ORBM 15 565 2* 3/8
3.5” HYDRAULIC CYLINDER ASSEMBLY & PARTS LIST 16 19 18 1 20 3 G A 5 F 6 C 2 E 18 A 25 G 4 25 - Seal Kit 3-1/2 Hyd Cylinder (includes items A through G) D B 7 15 17 CD5990 REF A PART QTY 1003197 DESCRIPTION Cylinder, Hyd 3-1/2 x 10 (Tilt) REF 25 PART QTY 1005000 DESCRIPTION Seal Kit 3-1/2 Hyd Cylinder (Includes Items A - G) 1 N/S 1 Clevis Cap 2 N/S 1 Rod Cap 3 1004826 1 Piston, 3-1/2 Hyd Cylinder A 2 O-Ring 4 1004829 1 Rod, Hyd Cylinder 1.
4.0” HYDRAULIC CYLINDER ASSEMBLY & PARTS LIST 1 A 3 2 5 E 7 - SEAL KIT 1005015 F B 6 G 4 D C A 1 2 3 4 H D C H G F CD6063 7 - SEAL KIT 6 REF PART 1005016 QTY B DESCRIPTION A 1005015 1 Hyd Cylinder 4.00 x 2.00 x 30.00 A 1005016 1 Hyd Cylinder 4.00 x 2.00 x 16.00 1 1004290 1 Piston, 4.00 OD x 1.00 ID 2 N/S 1 3 1004291 1 5 E REF DESCRIPTION Seal Kit - 4.0 Dia Hyd Cylinder (Includes Items A - H) A 1 Crown Seal Tube Assembly B 1 O-Ring Rod, 2.0 x 38.
PNEUMATIC TAIL WHEEL KIT 29399 REF PART QTY PART REF 1 29399 1 Tail Wheel, Pneumatic Complete 15 2 ——— 1 Tire, Wheel & Hub 16 3 14125 1 Wheel Yoke Assembly 4 5 6 7 PART 28789 QTY 1 DESCRIPTION 1 x 12-1/4 Clevis pin 1972 1* Grease Fitting, 1/4-28 Tapered Thread 17 29031 Friction disc 4 x 6.15 18 29030 1 Floating link, Right Top Dampener plate 19 29034 1 Sleeve, 1.00 x 1.25 x 1.
WHEEL HUB, TIRE & WHEEL ASSEMBLY REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 14130 1 Wheel Hub & Axle Assembly 10 1257 2* 3/4 Flat washer, Standard 2 3626 1 Nut, Hex 1-14 UNS 11 5849 1 Nut, Slotted Hex 3/4 NF 12 14133 1 Hub Cap Assembly w/fitting 3 4 5 6 1863 1* 1 Flat washer, Standard 14131 1 Axle Assembly 1266 1* 3/16 x 1-1/2 Cotter pin 314 1 Seal, 1.50 x 2.44 x .
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 IN MM 1/2 5/8 3/4 7/8 1 2 3 4 5 6 7 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG ............................................................. Agriculture NC .................................................... National Coarse ATF...............................
WARRANTY (All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles) Please Enter Information Below and Save for Future Reference. Date Purchased: __________________________ From (Dealer): ________________________________________ Model Number: __________________________ Serial Number:________________________________________ Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship.
WARRANTY (Replacement Parts For All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.
MAN0161 Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois 61061 815-732-2141 tel 815-732-7580 fax www.WoodsEquipment.com © 2002 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders.
