Rev. 10/8/2004 52619 MF6000 MF6600 MF7200 GF3000 Tested. Proven. Unbeatable.
TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration included in the Operator’s Manual. Both dealer and customer must sign the registration which certifies that all Dealer Check List items have been completed.
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL INFORMATION The purpose of this manual is to assist you in operating and maintaining your manure fork. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance. These instructions have been compiled from extensive field experience and engineering data. Some information may be general in nature due to unknown and varying operating conditions.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act. Make sure that all operating and service personnel know that if hydraulic fluid penetrates skin, it must be surgically removed as soon as possible by a doctor familiar with this form of injury or gangrene, serious injury, or death will result.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! lockpins must be fully extended and properly engaged into attachment retaining slots. Power unit must be equipped with ROPS and seat belt/operator restraint. Keep seat belt/operator restraint securely fastened/engaged. Falling off power unit can result in death from being run over or crushed. Keep ROPS systems in place at all times. Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.
• Carry loads low and drive slowly. • Do not carry large objects that can fall out of attachment into operator zone. • Never lift load higher than necessary to clear the ground when moving. AVOID INJURY OR DEATH FROM FALLING OBJECTS: • This unit is not equipped with any method to prevent objects such as round bales, posts, or logs from rolling back onto operator. • Do not carry large objects that can fall out of attachment into operator zone.
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 2- Serial Number Plate 2 4 MODEL NO. 3 SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. BE CAREFUL! Use a clean, damp cloth to clean safety decals. Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off.
OPERATION Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.
Carefully move and align the skid steer coupler to the manure fork. The top of the skid steer coupler must index into the manure fork flange, Figure 2. PRE-OPERATION CHECK LIST (OWNER'S RESPONSIBILITY) ___ Review and follow all safety rules and safety decal instructions on page 3 through 6. ___ Check that all safety decals are installed and in good condition. Replace if damaged. ATTACHMENT FLANGE ___ Check that all shields and guards are properly installed and in good condition. Replace if damaged.
8-1/2” Tine Spacing CM1162 Figure 5. Manure Fork Transporting Loads A WARNING Improper operation can cause the machine to tip or roll over and cause injury or death. • Keep power unit lift arms and attachment as low as possible. • Do not travel or turn with power unit lift arms and attachment raised. • Turn only on level ground. • Go up and down slopes, not across them. • Keep the heavy end of the machine uphill. • Do not overload the machine.
Release brake and roll skid steer coupler until it is disengaged from the attachment. The attachment should be placed in storage position. CLEANING STORAGE ● Remove large debris such as clumps of dirt, grass, crop residue, etc. from machine. ● Inspect machine and replace worn or damaged parts. ● Replace any safety decals that are missing or not readable. A WARNING Follow manual instructions for storage. A After Each Use CAUTION Keep children and bystanders away from storage area.
OWNER SERVICE The information in this section is written for operators who possess basic mechanical skills. Should you need help, your dealer has trained service technicians available. For your protection, read and follow all safety information in this manual. A WARNING Safety instructions are important! Read all attachment and power unit manuals; follow all safety rules and safety decal information. (Replacement manuals and safety decals are available from your dealer.
ASSEMBLY Refer to parts drawing on page 14 when following assembly instructions. MANURE FORK (OPTIONAL TINES) Using a suitable hoist, support the fork main frame in an upright position. Insert fork tine (11) in mounting hole nearest the edge of the main frame until shoulder bottoms against the frame. Retain with cotter pin (15). Install base end of hydraulic cylinder (7) to backing plate (3) using pin (8). Secure with cap screw (20) and nut (19).
DEALER CHECK LISTS DELIVERY CHECK LIST PRE-DELIVERY CHECK LIST (Dealer's responsibility) Inspect the equipment thoroughly after assembly to ensure it is set up properly before delivering it to the customer. The following check lists are a reminder of points to inspect. Check off each item as it is found satisfactory or after proper adjustment is made. ___ Check that all safety decals are installed and in good condition. Replace if damaged.
MF6000, MF6600, MF7200 & GF3000 PARTS LIST 5 16 7 6 18 4 NOTE: Individual decal part numbers and locations are shown on Safety Decal page. 19 20 17 8 HOSE KIT -- See page 15. 19 21 22 3 9 23 10 24 16 25 2 CD5105 1 15 11 REF PART QTY DESCRIPTION REF PART 565 QTY - DESCRIPTION 1 54535 1 Grapple fork 21 3/8 Standard flat washer 2 56579 1 1.000 Dia. x 4.
HOSE KIT A WARNING Protective hose sleeves must cover all hydraulic hoses within 20 inches of the operator and be secured ont o metal hose fitt ings. Replace hoses or sleeves if damaged or if protective sleeve cannot be properly positioned or secured. IMPORTANT 3 2 TO QUICKDISCONNECT COUPLERS ■ Check with your dealer to select the correct hose kit for your skid steer.
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 IN MM 1/2 5/8 3/4 7/8 1 2 3 4 5 6 7 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG ............................................................. Agriculture NC .................................................... National Coarse ATF...............................
WARRANTY (Replacement Parts For All Models Except Mow’n Machines) WEC Company, d/b/a Woods Equipment Company (“WOODS”), warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.
WARRANTY (All Models Except Mow’n Machines) Please Enter Information Below and Save for Future Reference. Date Purchased: __________________________ From (Dealer): ________________________________________ Model Number: __________________________ Serial Number:________________________________________ WEC Company, d/b/a Woods Equipment Company (“WOODS”), warrants this product to be free from defect in material and workmanship.
52619 Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois 61061 815-732-2141 tel 815-732-7580 fax www.woodsonline.com © 2002 Woods Equipment Company. All rights reserved.
