WOODBRIDGE R Or Email: help@woodbridgebath.
WOODBRIDGE R IMPORTANT SAFEGUARDS When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following: 1. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. 2.
WOODBRIDGE R IMPORTANT SAFETY INSTRUCTIONS CAUTION – Indicates that failure to follow the instruction may cause body injury or property damage. 1. Do not install or use the product in wet places as steam room etc. 2. It is recommended to use water-proof electrical outlet which should be installed in a place where is not easily to get wet. 3. This product should be used with 110V-120V, 50/60Hz electrical current only, load current is at least 15A.
WOODBRIDGE R TECHNICAL SPECIFICATION Model Main Unit Toilet Cleaning device Deodorization 3 B0930S Rated voltage 110V-120V, 50/60Hz Rated power 875W Water proof IPX4 Power cord length About 2.3m Flush volume 1.6/1.1Gpf, 6.0L(full flush)/4.1L(half flush) Flushing mode Siphonic jet Rough-in 12 inches (305mm) Outlet outside diameter ≤ 3.9 inches (≤ 100mm) Drainage method S-trap Water pressure range Minimum water pressure 0.08MPa, Maximum water pressure 0.
WOODBRIDGE Drying device Heated seat Caring device R Warm air volume Over 0.
WOODBRIDGE R This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WOODBRIDGE R LIST OF MATERIALS Main Unit Remote Control Components Sealing Flange Rough-in Template WOODBRIDGE R Or Email: help@woodbridgebath.
TECHNICAL DRAWING 7/8'' Chair Height 17-3/8'' Ø3 /8 '' 13'' 19-3/4'' 39-7/8'' 3-7/8'' WOODBRIDGE R 3-1/8'' 10-7/8'' 1-3/4'' 13-5/8'' 7-1/4'' 20-1/4'' 16-1/2'' 8-1/8'' 12'' 27-5/8'' 1. The drawing is for reference only, and we reserve the right to modify the product appearance. 2. Product appearance is subject to change in kind.
WOODBRIDGE R DIMENSION/TECHNICAL DATA 3'' 20'' 3'' 2'' 2'' 11-3/4'' 19-3/4'' 1-3/4'' 16-7/8” 27-5/8'' 13-5/8'' The product drawing is for reference only, and we reserve the right to modify the appearance of the product.
WOODBRIDGE R Installation Option 15-3/4" 19-5/8" Inlet connector 1-3/4" Connect the water inlet and angle valve of the toilet with the matching hose and tighten it Ø3/8" 2-3/8" Flexible hose 16-1/2" 19-3/4" 31-1/2" Angle valve connector 15-3/4" Recommended location for remote control mounting (Left or Right) Rough-in 20" 12" Standard STANDARD INSTALLATION NO SHOW INSTALLATION Wall Power Outlet(GFCI) Water Outlet （Angle valve mounting) Wall Power Outlet(GFCI) Water Outlet （Angle valv
WOODBRIDGE R PARTS IDENTIFICATION Left side Bumper Lid Foam shield filling drawer Seat knob Ceramic toilet Right side Nozzle shield Dryer shield Night light sensor window Front washing Rear washing Spray nozzle Touch the sensing area with foot 10
WOODBRIDGE R 1. Install the matching three-way angle valve · Mark the center line of the sewage outlet on the ground, and install a three-way angle valve at a suitable position on the wall according to the size of the toilet. INSTALLATION OF CERAMIC TOILET 3. Mounting bracket installation · Assemble the mounting bracket with bolts and then install them to the pre-installed flange plate on the ground and lock tight with nuts.
WOODBRIDGE R 5. Screw installation 6. Connect the hoses · Put the screw through the fixing sleeve and then install it through the holes (on both sides of the toilet bowl) to the mounting bracket on the ground. Lock tight. · Install the decorative cap on the fixing sleeve. · Connect the water supply hose of the toilet tank and the water inlet hose of the toilet seat to the three-way angle valve as shown in the figure.
WOODBRIDGE R 7. Add foam agent (Please buy from local store) · Use your fingers or tools to reach under the filling box and pull out the filling box. (it is recommended to use a filling funnel, as shown below) · Close the sealing cap and press tightly, then push the filling drawer to the end.
WOODBRIDGE R PREVIOUS PREPARATEION 1. Turn on the three-way angle valve · Check the threaded connection for leaks to ensure complete sealing. Turn the three-way angle valve counterclockwise to the full open position. (Note: The three-way angle valve opens with a large torque for the first time.) Equipped with three-way angle valve 2. Power Connection · Plug in the leakage protection plug to a power socket, press the reset switch, plug indicator lights up, indicating that the power is on.
WOODBRIDGE R AUTO OPEN/CLOSE LID The intelligent toilet can achieve the function of auto lid open/close. On closed situation, so please function the auto lid open/close function by using remote controller. 1. Approaching the toilet When user enters the sensing range, the seat lid opens automatically. 2. Leaving the toilet The seat lid closes automatically after user leaves 180 seconds (3 minutes). 3. Standing up to urinate 1. Open the seat by remote control or hand. 2.
WOODBRIDGE R FOOT SENSOR The toilet is equipped with foot sensor lid-open function, it can make lid autoopen by sensing foot movement. 1. When the lid and seat are both closed, touch the sensing area with foot to open the lid. Lid Seat 2. When the lid is open and seat closed, touch the sensing area with foot to open the seat. Lid Seat 3. When the seat and lid are open, touch the sensing area with foot to close the seat and lid and activate a half flush.
WOODBRIDGE R DAILY MAINTENANCE Main unit care and maintenance Spray nozzle care and maintenance 1. Shut off power supply before doing maintenance. 1. When no one is seated, turn the knob clockwise. The nozzle will automatically stretch out to allow access for cleaning. 2. Use only a soft, damp cloth to clean. Avoid using harsh chemicals. 2. When the nozzle moves forward, the nozzle can be removed and cleaned separately. 3.
WOODBRIDGE R EMERGENCY TROUBLESHOOTING Power and water failure Product unused for a period of time · Fill up 2.1Gal (8L) water to a bucket and flush the ceramic bowl. · When the product is left unused for a long time, especially in cold weather, it is highly recommended to drain the water to prevent freezing. Note: Avoid water spilling from bowl. To discharge water 1. Activate flushing, and then turn off angle valve to stop water supply. 2. Unplug and disconnect from electricity. 3.
WOODBRIDGE R Knob function Anticlockwise rotation Clockwise rotation Push the knob Rear wash/ front wash In the seated state, turn the knob clockwise to start the feminine wash function, and turn it counterclockwise to start the rear wash function. After the first cleaning function (rear wash /front wash) is completed or short press the knob during the cleaning function, the warm air function and flushing function will be automatically activated.
WOODBRIDGE R DESCRIPTION OF THE TOP INDICATOR LIGHTS ② ③ ④ ① The power-on self-test is completed. ① Temperature: When the water temperature indicator light is on, it will display the water temperature, and when the seat temperature indicator light is on, it will display the seat temperature; the normal temperature will display [--].
WOODBRIDGE R Problem No water from nozzle Poor water spraying Low water temperature Low seat temperature Low dryer temperature Dryer not blowing Spray wand cannot retract Spray wand cannot stretch out Remote control cannot display 21 TROUBLE SHOOTING GUIDE Cause Solution Water supply hose is kinked Straighten the hose to remove the kink Angle valve is off Turn on the angle valve A water failure occurred Restore the water supply Water supply hose is kinked Straighten the hose to remove the
WOODBRIDGE Problem R Cause Solution User is not within the sensing area of the seat Adjust position on seat to activate the sensor Deodorization function continues after user leaves It is normal for the deodorizing function to continue operating after user leaves, for complete odor removal Foam shield has a small amount of foam Foam agent run out Add foam agent After replacing the foam agent, the amount of foam produced by the foam shield is small Air in the foam shield line after the foam agent
23
Or Email: help@woodbridgebath.com ASVFAF0321023A-1.
