User's Manual

FAQ
The earbuds are on, but not connecting to my device
For the earbuds and your device to establish a connection,
you need to put them both in pairing mode. Please follow the
instructions in the Pairing section of this manual.
I’ve connected the earbuds with my smartphone but can’t
hear any sound
Double-check the volume level on your smartphone and the
earbuds. Some smartphones require you to set up the earbuds
as an audio output device before the audio can be transmit
ted. If you’re using a music player or other device, please
make sure it supports the A2DP profile.
Controls & LED Indicators
Streaming Audio
Once paired, you can wirelessly stream audio from your device
to the earbuds. Music will automatically pause when you receive
an incoming phone call and resume once the call has ended.
Taking Calls
Turning On / Off
Pairing
Pairing starts with the earphones in the earphone box: 1. Take
out the left and right earphones from the earphone box. The
LED indicator on the headset will flash blue and red. This
means they can start pairing. 2. Turn on the pairing function
(Bluetooth) on the device you want to pair with the earbuds.
Find and select "MVPower T82" from the list of available
devices to connect 3. If a password or PIN is required for
pairing, please enter "0000". After successful pairing, you can
turn on and off the earbuds as follows: Take out the
earphones from the charging box and the earphones It will
automatically turn on, put the earphone back into the
charging box and then turn off, the earphone indicator light,
the red light flashes three times at 150ms, once every 10S
cycle, please put the earphone back into the charging box
and start charging
Model
Hardware solution
Speaker size
Sensitivity
Frequency Range
Speaker impedance
Microphone type
Microphone sensitivity
MIC frequency range
The scope of work
Charging input
Charging time of charging
compartment
Battery Type
Headphone charge times
Turn On
Turn Off
Play or pause
Skip to next track
Skip to previous track
Double-tap the touch-sensitive panel
on either earbud
Long-press the right earbud for 2
seconds
Long-press the left earbud for
2 seconds
Remove both earbuds from the charging case
Return both earbuds to the charging case
T82
AD6973A4
13MM
106 ±3dB (1kHz)
20Hz – 20kHz
16 ohm ±15%
MEMS
-38dB
200Hz – 5kHz
10m
DC5V
2H
350mAh
4 Times
Using the Left/Right Earbud Only
Starting with the earbuds in the case:
1.
2.
3.
Notes
●
●
●
●
●
Take the left/right earbud out
Turn on the pairing function on the device you want to pair
with the earbud
From the list of available devices, find and select
"MVPower T82
When you turn on the earbuds, they will automatically
reconnect to the last-paired device or enter pairing mode if
no paired device is found
To clear the pairing list, remove both earbuds from the
charging case, tap and hold the touch-sensitive panel on
both earbuds for 10 seconds
In pairing mode, the earbuds will automatically turn off after
5 minutes if no devices are paired
If one of the earbuds has no sound output, put both earbuds
back into the charging case and take them out again
The maximum wireless operating range is 10m (33ft). If you
exceed this range, the earbuds will disconnect from your
paired device. The connection will be re-established if you
re-enter the wireless range within 5 minutes. The earbuds will
automatically reconnect to the last-paired device. To
connect with other devices, refer the previous pairing steps
Answer or end
a call
Reject an
incoming call
Use Siri or other
voice assistants
Double-tap either earbud to answer or end
a call. If there’s a second incoming call,
double-tap to answer the second call and
put the first call on hold; or long-press for 2
seconds to reject the second call
Long-press either earbud for 2 seconds
While your device is connected, triple-tap
either earbud
LED Status Indicator (Earbuds)
Flashing red and blue
Red and blue flashing alternately
Steady red
Lights off
LED Charging Indicator (Charging case)
Red indicator light flashes
Long bright
Status
Charging
Fully charged
Status
Pairing mode
Reconnecting
Charging
Fully charged
The sound isn’t very clear or the caller can’t hear my voice
clearly
Adjust the volume on your smartphone and the earbuds. Try
moving closer to your smartphone to rule out the possibility of
interference or wireless range-related issues.
What’s the wireless range of the earbuds?
The maximum range is 10m (33ft). However, the actual range
depends on environmental factors. For optimal performance,
keep your device connected within a range of roughly 4m to
8m and make sure that there are no major obstacles (like
reinforced steel walls) between the earbuds and your device.
The earbuds won’t turn on
Try charging the earbuds for a while. If the earbuds still won’t
power on, please contact our support team at the email
address given in Warranty & Customer Support.
I put the earbuds back in the charging case, but the earbuds
are still connected
In this case, the charging case is likely to be out of power. You
will need to charge the case.
Product Care & Use
●
●
Keep away from liquids and extreme heat
Don’t use the earbuds at high volume for extended periods,
as this may cause permanent hearing damage or loss
Warranty & Customer Support
For questions, support, or warranty claims, contact us at the
address below that corresponds with your region. Please
include your Amazon order number and product model number.
*Please note, MVPower can only provide after sales service for products
purchased directly from MVPower. If you have purchased from a different
seller, please contact them directly for service or warranty issues.
FCC Information for Users
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1.This device may not cause harmful interference.
2.This device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio commu
nications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by
one or more of the following measures:
●
●
●
●
This equipment complies with FCC RF radiation exposure limits
set forth for an uncontrolled environment.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
- 01 - - 02 - - 03 - - 04 - - 05 - - 06 - - 07 - - 08 - - 09 - - 10 -
User Manual
Wireless Earbuds
Before starting charging for the first time, please fully charge
the charging case. To charge, please use the included
typec-usb data cable to connect the charging case to the
USB charger or charging port. When the LED charging
indicator is always on, it means the case is fully charged. The
charging time is about 2 hours, and the earplugs can be fully
charged 4 times after being fully charged. When not in use,
keep the earplugs in the earphone case. When the earphone
is charged in the earphone box, the LED indicator on the
earbud will turn into a solid red. When the indicator light is off,
the headset is fully charged.
(Note! The circuit diagram is subject to the actual product)
Thank you for purchasing the MVPower T82 True Wireless
Earbuds. Please read this user manual carefully and keep it for
future reference. If you need any assistance, please contact
our support team with your product model number and
Amazon order number.
Package Contents
True Wireless Earbuds
Charging Case
USB Cable
Product Diagram
Getting Started
Charging
Specifications
Earbuds
English
Italiano
Deutsch
Français
Español
01 ~ 11
45 ~ 55
12 ~ 22
23 ~ 33
34 ~ 44
Contents
Japan 56 ~ 66
FCC ID：WC2-00T82
Wonders Technology Co., Ltd.
Email: [e-mail]
Add: 4/F, Tower A, 3rd Building, Tian’an Cloud Park, Bantian
Avenue,Longgang District, Shenzhen 518129, China
User Manual
Made in China
208-190161
Touch-Sensitive Panel
LED Indicator
USB Charging Port
USB Charging Port
LED Charging
Indicator
EN EN EN EN EN EN EN EN EN EN
Model: T82