Product Manual

ManualsBrandsWolo ManualsAutomotiveLighting Strobe Light Kit – 4 Clear Strobe Bulbs, 12-24 Volt

WOLO-LIGHTNING

80 WATT / 4 OUTLET 12-24 VOLT

POWER SUPPLY & STROBE LIGHT KIT

6 Different Light Patterns 8004 SERIES

INSTALLATION INSTRUCTIONS

Your purchase of Wolo’s LIGHTNING strobe light system is the perfect choice to compliment your vehicle’s

emergency warning lights. Wolo’s strobe kits are manufactured with the finest materials. Each light is tested to

meet our high standards to ensure that all functions work perfectly. Our quality workmanship and components

are Wolo’s assurance that this product will provide years of dependable service. If you need help using or

installing your new Wolo warning light, our technicians are available to answer your questions, Monday thru

Friday, from 9 AM to 4 PM EST at 888-550-4676.

Before installation of the strobe power supply and bulbs is attempted, it is important to read these instructions

completely. The lives of people are dependent on the proper installation. The person installing this light must

have advanced knowledge of the proper method of installing emergency warning lights to a vehicle as well as

knowledge of the vehicle's electrical system. Again, read this manual completely and note any messages

marked ‘‘IMPORTANT” or ‘‘WARNING”. A safe installation will prevent serious injury or damage to the

vehicle.

LIGHTNING, is completely wired and does not require any wiring inside the power supply. There are four (4)

power cables included in the kit; two (2) that are 3 meters / 9.8 ft. in length for installation in front of vehicle

and two (2) that are 5 meters / 16.4 ft. in length for installation in rear of vehicle. Also included in the kit is a

control panel, dash mountable with an on/off switch and a push button switch to change the strobe light

pattern, all that is required for a successful installation.

Installation of LIGHTNING requires drilling to the vehicle. The installer must carefully inspect both sides of any

location that will be drilled to ensure that there are no components, wires and or any vehicle parts that could

be damaged when drilling.

IMPORTANT: Always de-burr any drilled holes to ensure that there are no sharp edges. Install a rubber

grommet into all metal holes that the wires are being routed through.

Always refer to the vehicle’s shop manual for the deployment location of the air bags. Never install the control

panel switches, wires and/or components in the deployment area of any air bag. Improper installation could

reduce the effectiveness of the vehicle's air bag system and/or project an object that could cause serious

personal injury or death to the driver or passenger. The user/installer assumes all responsibility to properly

access a safe mounting location for the switch control panel, so to provide ultimate safety to the driver and

passengers inside the vehicle.

All LIGHTNING models produce both high voltage and high current. To operate this product at peak

performance, the black wire should always be connected directly to the (-) negative battery post. If the length

of the black wire needs to be made longer, use a minimum 18 gauge or heavier.

The vehicle operator and/or maintenance department should inspect the strobe light system frequently to

ensure that all bulbs are functioning and are securely held in the vehicle’s light assembly.

These installation instructions should always be kept and stored in a safe location so that they can be referred

to when information, maintenance or reinstallation is required. Failure to follow all safety precautions and

installation procedures as outlined in these instructions could result in property damage to the vehicle, serious

injury or death to you or others.

Summary of content (5 pages)

PAGE 1
WOLO-LIGHTNING® 80 WATT / 4 OUTLET 12-24 VOLT POWER SUPPLY & STROBE LIGHT KIT 6 Different Light Patterns 8004 SERIES INSTALLATION INSTRUCTIONS Your purchase of Wolo’s LIGHTNING strobe light system is the perfect choice to compliment your vehicle’s emergency warning lights. Wolo’s strobe kits are manufactured with the finest materials. Each light is tested to meet our high standards to ensure that all functions work perfectly.
PAGE 2
WARNING • All 8004 models contain four (4) strobe bulbs. At a close distance, never look directly at the bulbs when the power supply is turned on. Momentary blindness and/or permanent eye damage could occur. • The strobe power supply produces HIGH VOLTAGE. Never touch or remove any of the strobe bulbs while in operation. Wait no less than 10 minutes after disconnecting the power supply from it’s power source to attempt to handle bulbs or troubleshoot.
PAGE 3
6. Clean the interior of light assembly and lens of any dust or filings, which may have developed during cutting the hole. 7. Re-install the OEM factory light assembly and reflector. 8. Install the strobe bulb into the one inch hole drilled into the light assembly. Hold the bulbs rubber grommet and use a twisting motion while pushing inward until the grommet’s recessed ring engages into the light’s assembly. 9. Repeat the same installation procedure for the remaining bulbs. WIRING STROBE BULBS Fig.
PAGE 4
WIRING SWITCH CONTROL PANEL TO 12-24 VOLTS. Fig. F WARNING: The power supply has an external 15-amp fuse to protect its internal circuit. The 15-amp in-line fuse attached to the red wire must be connected “AT A POWER SOURCE” so to protect the wire connection between the power source and power supply. RED INSTALLATION IS COMPLETE Position the on/off switch to “ON“. Press and release the push button to change the light pattern. Flash Pattern 1. Triple Fast Flash 2. Triple Flash 3. Rapid Rate 4.
PAGE 5
Warranty Wolo Manufacturing Corporation (“Wolo”) warranties to the original purchaser, for three months from the date of purchase, that this product is free from defects in workmanship and materials. If there is such a proven defect, Wolo, at its option, will either repair or replace the item free of charge, if it is returned to Wolo within three months from the date of purchase together with proof of purchase as described below.