Technical Specifications

ManualsBrandsWolman ManualsPaint1-qt. Classic Clear Above Ground Wood Preservative-(6-Pack)

TECHNICAL DATA WLF-01

WOODLIFE

CLASSIC CLEAR WOOD PRESERVATIVE

Form: GDH-797

Rev.: 061815

.DESCRIPTION AND USES .

Woodlife

Classic Clear Wood Preservative is a clear,

fungicidal exterior wood preservative with water repellent

designed for use on above ground applications where

either pressure-treated or non-pressure-treated wood has

been used. Woodlife Classic protects against rot and

decay by inhibiting mold, mildew, and staining fungus

growth on the wood surface. It has excellent water

repellency and anti-wicking properties which resist

moisture absorption through the surface sides and end

cuts to give greater resistance to dimensional warping,

splitting and end-checking. The paintable and stainable

formula will extend topcoat service life by inhibiting peeling

and blistering.

Use on above ground installation only. Use on all

species of untreated or pressure-treated lumber including

plywood or engineered wood items. It is suitable for decks,

porches, fencing, siding, outdoor furniture, gazebos and

arbors, storage sheds, play equipment or other

engineered wood items exposed to weather and rain. It is

especially suitable as a preservative primer for wood

windows, doors, frames, trim and millwork, shake

shingles, clapboard and log siding, and other exterior

wood intended to be over-coated with paint or stain.

SPECIAL FEATURES

 Resists moisture damage, including swelling,

shrinking, warping, splitting and end-checking.

 Paintable or stainable after 24 hours.

 Extends topcoat service life by preventing moisture

absorption that can cause peeling and blistering.

 Can be applied immediately to new wood. No need

to wait for wood to weather or “season”.

 Water-based formula allows for fast, easy clean up

with soap and water.

 100% Clear allows for natural wood color to show

through and gray naturally.

PRODUCTS .

SKU Description

902 1-Quart

903 1-Gallon

78904 5-Gallon

.PRODUCT APPLICATION .

SURFACE PREPARATION

All cutting, gluing, and sanding should be done before

applying this product. DO NOT use steel wool. Wood

surface must be dry and free of dust, dirt, debris and

standing water. This product will adhere to dry or damp

(not soaking wet) surfaces. Proper surface preparation is

required to ensure adequate penetration, adhesion, and

optimum performance.

.PRODUCT APPLICATION (cont.) .

New Wood – If wood is “brand new” intended for outdoor

installation and exposed to weather conditions for 30 days

or less, a “splash test” (see Splash Test below) should be

performed to determine if there is any surface barrier

present which would repel a new coating. Barriers include

paraffin wax, found on some types of pressure-treated

wood or mill glaze found on Cedar and Redwood. Use

Wolman

DeckStrip

or Wolman

Deck & Fence

Brightener to remove any surface barrier detected, then

conduct splash test again to confirm penetrability before

applying this product.

Splash Test - Sprinkle a few drops of water on several

areas of the surface to be coated. If the water is absorbed

rapidly, the surface is ready to be finished with Woodlife

Classic. If the water beads are not absorbed into the

wood, a surface barrier exists and must be removed.

Apply or Wolman

Deck & Fence Brightener and then test

again.

Weathered Wood - For all outdoor wood structures

except "brand new," the surface must be dry and free of

any colored paints, stains, varnishes, clear finishes, as

well as ground-in-dirt, grayed surface fibers and tannin,

algae or mildew stains. Use of a stain stripper like Wolman

DeckStrip

or Wolman

Deck & Fence Brightener is

recommended to properly prepare the surface before

applying Woodlife Classic. Once surface preparation is

completed, perform a "splash test" to confirm the

penetrability of the wood surface, and repeat cleaner or

stripper application if necessary.

IMPORTANT! Preparing surfaces with products containing

chlorine bleach (sodium hypochlorite) alone is NOT

recommended. These products can leave dirt deposits

and degraded wood fibers on the surface, which interfere

with the penetration, adhesion and coloration of protective

coatings.

APPLICATION

Before You Start – To minimize clean-up afterward, cover

surrounding landscape and exposed brick, glass,

aluminum, and vinyl siding with cardboard, plastic or cloth

tarps. Protect plants, shrubs and vegetation from

overspray. If the surface is in direct sunlight and hot to the

touch, dampen with fresh water to cool. Remove any

standing water before beginning application. This product

will adhere to dry or damp (not soaking wet) surfaces. This

product has a milky appearance in the can and a whitish

appearance when applied, but dries clear.

IMPORTANT: Before beginning project, perform a

sample brush-out in several inconspicuous areas to

ensure the desired look is achieved. Color appearance

will vary with wood age, species and surface porosity.

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA WLF-01 WOODLIFE® CLASSIC CLEAR WOOD PRESERVATIVE .DESCRIPTION AND USES . .PRODUCT APPLICATION (cont.) ® New Wood – If wood is “brand new” intended for outdoor installation and exposed to weather conditions for 30 days or less, a “splash test” (see Splash Test below) should be performed to determine if there is any surface barrier present which would repel a new coating. Barriers include paraffin wax, found on some types of pressure-treated wood or mill glaze found on Cedar and Redwood.
PAGE 2
TECHNICAL DATA WOODLIFE® CLASSIC CLEAR WOOD PRESERVATIVE .PRODUCT APPLICATION (cont.) . Use in an area with adequate ventilation at all times. Apply only when air (ambient) temperature is between 50-90°F (10-32°C) and relative humidity is below 85% and when no precipitation is expected within 24 hours. Use full strength. Do not thin. Mix thoroughly before and during use. Apply with a synthetic bristle brush, a ¼” short nap style roller, or a pump style sprayer such as a Wolman BackSaver 2Gallon Sprayer.
PAGE 3
TECHNICAL DATA WOODLIFE® CLASSIC CLEAR WOOD PRESERVATIVE .PHYSICAL PROPERTIES . WOODLIFE CLASSIC CLEAR WOOD PRESERVATIVE Resin Type Acrylic Pigments NA Solvents Water Per Gallon Weight Solids 8.40 lbs. Per Liter 1.00 kg By Weight 4.0% By Volume 4.1% Volatile Organic Compounds <250 g/l Practical Coverage at Recommended DFT (assumes 15% material loss) Touch Dry Times at 70-80°F (21-27°C) and 50% Relative Humidity 150-250 sq.ft./gal.