Use and Care Manual

ManualsBrandsWolman ManualsExterior Paint & StainDuraStain® One Coat Chestnut Brown Semi-Transparent Stain - 1 gal.

TECHNICAL DATA

WOL-16

DURASTAIN

ONE COAT SEMI-TRANSPARENT STAIN

Form: GDH-697

Rev.: 020921

DESCRIPTION AND USES

Wolman

™

DuraStain

One Coat Semi-Transparent Stain is a

one coat, water-based exterior wood stain designed to

provide excellent color retention, adhesion and protection

against UV graying, water damage and mildew. DuraStain

decorates wood with a deeply pigmented color in a matte

finish that enhances wood texture and provides semi-

transparent hide coverage over new or previously coated,

weathered wood.

The hydrophobic technology properties and excellent water

repellency helps maximize resistance to wood cracking,

checking, splitting and warping. DuraStain is suitable for use

on all types of pressure treated lumber, Cedar, Redwood,

Poplar, Hickory and other North American hardwoods.

Use DuraStain to beautify and protect decks, porches,

fences, shake, shingle and clapboard siding, boat decks,

boardwalks, outdoor furniture, gazebos, arbors and trellises,

storage sheds and more.

DO NOT USE ON ANY CONCRETE SURFACE. Do not use

on driveways, garages or other areas with vehicular traffic.

TINT BASE MUST BE TINTED BEFORE USE

Wolman DuraStain One Coat can be applied using a ⅜”

nap roller, a short nap stain pad or a synthetic paint

brush.

PERFORMANCE CHARACTERISTICS

 One coat application

 Ready for use in 48 hours

 Mildew resistant coating

 Superior water repellency

PRODUCTS

SKU

DESCRIPTION

288078

Natural Cedar (1-Gallon)

288081

Chestnut Brown (1-Gallon)

288082

Neutral Base (1-Gallon)

288087

Natural Redwood (1-Gallon)

288091

Saddle Brown (1-Gallon)

288099

Neutral Base (5-Gallon)

288102

Natural Cedar (5-Gallon)

PRODUCT APPLICATION

SURFACE PREPARATION

REGARDLESS OF AGE OR SURFACE CONDITION, FAILURE

TO FOLLOW ONE OF THESE PREPARATION METHODS WILL

RESULT IN POOR ADHESION AND POSSIBLE COATINGS

FAILURE. NEW AND SEALED WOOD DECKS NEED TO

WEATHER AT LEAST 6 MONTHS BEFORE APPLICATION.

Prepare the surface with Wolman DeckStrip

DeckStrip ASR, then use Wolman DeckBrite

™

or Deck &

Fence Brightener based on wood condition described

below.

After preparation, conduct a Splash Test on bare wood

(described below) to confirm water absorption before

applying this product.

PREVIOUSLY COATED, WEATHERED WOOD

For best results, previous coatings such as paints, solid color

and semi-transparent stains, transparent stains, toners or

clear sealers in a weathered state, should be stripped to

create a bare, sound surface for maximum coating adhesion

and durability. To remove oil, alkyd or latex, water base

stains, use Wolman DeckStrip Stain & Finish Remover. For

100% acrylic solid or semi-solid stains, use Wolman

DeckStrip ASR Acrylic Stain Remover.

Thoroughly clean with Wolman DeckBrite or Deck & Fence

Brightener to remove chalky paint residue, embedded dirt,

mildew and other contaminants, residual coating material

and water repellents. According to label guidelines, select

the appropriate cleaning product for your wood type, use

according to directions and rinse with a power washer for

best results. When dry, scrape off and sand any remaining

loose flaking or peeling coating using 50 or 60 grit

sandpaper. After wood is dry, conduct a splash test

(described below).

UNCOATED, WEATHERED WOOD

Before staining, bare, weathered wood must be thoroughly

cleaned to remove ground-in dirt, mildew, mold and algae

stains, gray, UV damaged wood fibers any other surface

contaminants. According to label guidelines, select the

appropriate product for your particular wood type, either

Wolman DeckBrite or Deck & Fence Brightener; then follow

usage directions on the label, rinse and let dry. After wood is

rinsed and dry, conduct a Splash Test (described below).

Summary of content (4 pages)

PAGE 1
TECHNICAL DATA WOL-16 DURASTAIN® ONE COAT SEMI-TRANSPARENT STAIN DESCRIPTION AND USES PRODUCT APPLICATION Wolman™ SURFACE PREPARATION DuraStain® One Coat Semi-Transparent Stain is a one coat, water-based exterior wood stain designed to provide excellent color retention, adhesion and protection against UV graying, water damage and mildew.
PAGE 2
TECHNICAL DATA WOL-16 DURASTAIN® ONE COAT SEMI-TRANSPARENT STAIN PRODUCT APPLICATION (cont.) PRODUCT APPLICATION (cont.) SURFACE PREPARATION (cont.) APPLICATION UNCOATED, NEW WOOD ONE LIBERAL COAT OF WOLMAN DURASTAIN ONE COAT TRANSPARENT STAIN IS REQUIRED. New wood decks need to weather at least 6 months before application. After wood has weathered 6 months, it is important to open wood pores and remove any surface barrier which would prevent the proper penetration or adhesion of a new coating.
PAGE 3
TECHNICAL DATA WOL-16 DURASTAIN® ONE COAT SEMI-TRANSPARENT STAIN PRODUCT APPLICATION (cont.) COVERAGE Approximately 250 square feet per gallon. Depends on the applicator and the porosity of the wood. CLEAN-UP Clean up drips or spatters with water IMMEDIATELY, as dried stain is very difficult to remove. Clean up tools and equipment immediately after use with mild soap and fresh water. If dried, use mineral spirits or lacquer thinner. STORAGE KEEP FROM FREEZING. Close container when not in use.
PAGE 4
TECHNICAL DATA WOL-16 DURASTAIN® ONE COAT SEMI-TRANSPARENT STAIN PHYSICAL PROPERTIES ONE COAT SEMI-TRANSPARENT STAIN Resin Type Modified Alkyd/Acrylic Blend Pigment Type Iron Oxides and Mica Solvents Water Per Gallon Weight 8.5-8.6 lbs. Per Liter 1.0 kg By Weight 22.0-22.9% By Volume 19.4-20.2% Solids Volatile Organic Compounds <100 g/l (0.83 lbs./gal.) Recommended Dry Film Thickness (DFT) Per Coat 1.0-1.5 mils (25-37.5µ) Wet Film to Achieve DFT 5.0-7.5 mils (125-187.