Technical Specifications

ManualsBrandsWolman ManualsExterior Paint & StainDuraStain® One Coat Chestnut Brown Semi-Transparent Stain - 1 gal.

TECHNICAL DATA WOL-16

DURASTAIN

ONE COAT SEMI-TRANSPARENT STAIN

1 Form: GDH-697

Rev.: 052418

.DESCRIPTION AND USES

Wolman

™

DuraStain

One Coat Semi-Transparent Stain is a

one coat, water-based exterior wood stain designed to provide

excellent color retention, adhesion and protection against UV

graying, water damage and mildew. DuraStain decorates wood

with a deeply pigmented color in a matte finish that enhances

wood texture and provides semi-transparent hide coverage over

new or previously coated, weathered wood.

The NeverWet

hydrophobic technology properties and excellent

water repellency helps maximize resistance to wood cracking,

checking, splitting and warping. DuraStain is suitable for use on

all types of pressure treated lumber, Cedar, Redwood, Poplar,

Hickory and other North American hardwoods.

Use DuraStain to beautify and protect decks, porches, fences,

shake, shingle and clapboard siding, boat decks, boardwalks,

outdoor furniture, gazebos, arbors and trellises, storage sheds

and more.

DO NOT USE ON ANY CONCRETE SURFACE. Do not use on

driveways, garages or other areas with vehicular traffic.

TINT BASE MUST BE TINTED BEFORE USE

Wolman DuraStain One Coat can be applied using a ⅜” nap

roller, a short nap stain pad or a synthetic paint brush.

..PRODUCTS .

SKU Description

288078 Natural Cedar (1-Gallon)

288081 Chestnut Brown (1-Gallon)

288082 Neutral Base (1-Gallon)

288087 Natural Redwood (1-Gallon)

288091 Saddle Brown (1-Gallon)

288099 Neutral Base (5-Gallon)

288102 Natural Cedar (5-Gallon)

..PERFORMANCE CHARACTERISTICS .

 One coat application

 Ready for use in 48 hours

 Mildew resistant coating

 Superior water repellency

 NeverWet properties

..PRODUCT APPLICATION .

SURFACE PREPARATION

REGARDLESS OF AGE OR SURFACE CONDITION,

FAILURE TO FOLLOW ONE OF THESE PREPARATION

METHODS WILL RESULT IN POOR ADHESION AND

POSSIBLE COATINGS FAILURE. NEW AND SEALED WOOD

DECKS NEED TO WEATHER AT LEAST 6 MONTHS

BEFORE APPLICATION.

Prepare the surface with Wolman DeckStrip

or DeckStrip

ASR, then use Wolman DeckBrite

™

or Deck & Fence

Brightener based on wood condition described below.

..PRODUCT APPLICATION (cont.) .

SURFACE PREPARATION (cont).

After preparation, conduct a Splash Test on bare wood

(described below) to confirm water absorption before applying

this product.

PREVIOUSLY COATED, WEATHERED WOOD

For best results, previous coatings such as paints, solid color and

semi-transparent stains, transparent stains, toners or clear

sealers in a weathered state, should be stripped to create a bare,

sound surface for maximum coating adhesion and durability. To

remove oil, alkyd or latex, water base stains, use Wolman

DeckStrip Stain & Finish Remover. For 100% acrylic solid or

semi-solid stains, use Wolman DeckStrip ASR Acrylic Stain

Remover.

Thoroughly clean with Wolman DeckBrite or Deck & Fence

Brightener to remove chalky paint residue, embedded dirt,

mildew and other contaminants, residual coating material and

water repellents. According to label guidelines, select the

appropriate cleaning product for your wood type, use according

to directions and rinse with a power washer for best results.

When dry, scrape off and sand any remaining loose flaking or

peeling coating using 50 or 60 grit sandpaper. After wood is dry,

conduct a splash test (described below).

UNCOATED, WEATHERED WOOD

Before staining, bare, weathered wood must be thoroughly

cleaned to remove ground-in dirt, mildew, mold and algae stains,

gray, UV damaged wood fibers any other surface contaminants.

According to label guidelines, select the appropriate product for

your particular wood type, either Wolman DeckBrite or Deck &

Fence Brightener; then follow usage directions on the label, rinse

and let dry. After wood is rinsed and dry, conduct a Splash Test

(described below).

UNCOATED, NEW WOOD

New wood decks need to weather at least 6 months before

application. After wood has weathered 6 months, it is important

to open wood pores and remove any surface barrier which would

prevent the proper penetration or adhesion of a new coating. If

pressure-treated lumber, excess surface wax or excessive

internal moisture content may be present. If new wood is Cedar

or Redwood, “mill glaze” on the surface is a common condition.

Eliminate these barriers by using either Wolman DeckBrite or

Deck & Fence Brightener. According to label guidelines, select

the appropriate product for your particular wood type, follow

usage directions on label, rinse and let dry. After wood is rinsed

and dry, conduct a Splash Test (described below).

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA WOL-16 DURASTAIN® ONE COAT SEMI-TRANSPARENT STAIN .DESCRIPTION AND USES ™ ..PRODUCT APPLICATION (cont.) . ® Wolman DuraStain One Coat Semi-Transparent Stain is a one coat, water-based exterior wood stain designed to provide excellent color retention, adhesion and protection against UV graying, water damage and mildew.
PAGE 2
TECHNICAL DATA WOL-16 DURASTAIN ONE COAT SEMI-TRANSPARENT STAIN ..PRODUCT APPLICATION (cont.) ..PRODUCT APPLICATION (cont.) . . Perform a Splash Test APPLICATION (cont.) To conduct a Splash Test, sprinkle several handfuls of water on a few distinct areas of the bare wood surface. If the water absorbs rapidly, the surface is ready to be coated. If the water beads, puddles or is not absorbed, an internal or external barrier exists, and must be eliminated before staining can begin.
PAGE 3
TECHNICAL DATA WOL-16 DURASTAIN ONE COAT SEMI-TRANSPARENT STAIN PHYSICAL PROPERTIES . ONE COAT SEMI-TRANSPARENT STAIN Resin Type Modified Alkyd/Acrylic Blend Pigment Type Iron Oxides and Mica Solvents Weight Water Per Gallon 8.5-8.6 lbs. Per Liter Solids 1.0 kg By Weight 22.0-22.9% By Volume 19.4-20.2% Volatile Organic Compounds <100 g/l (0.83 lbs./gal.) Recommended Dry Film Thickness (DFT) Per Coat 1.0-1.5 mils (25-37.5µ) Wet Film to Achieve DFT 5.0 -7.5 mils (125-187.5µ) 311-324 sq.