Technical Specifications

ManualsBrandsWolman Manuals& RemoversDeck & Fence Brightener Wood Cleaner & Coating Prep - 1 gal.

TECHNICAL DATA WOL-05

DECK & FENCE BRIGHTNER

WOOD CLEANER & COATING PREP

Form: GDH-929

Rev.: 120817

.DESCRIPTION AND USES .

Wolman

Deck & Fence Brightener Wood Cleaner & Coating

Prep functions as two products. It is a cleaner for weathered

wood and a pre-coating preparation for new or weathered wood.

When mixed with water, Deck & Fence Brightener liquid

concentrate quickly and safely restores dirty, weathered-gray,

mildew and algae-stained wood to its natural, like-new look. It

also removes rust stains from nail bleed and black tannin stains

from tannin-rich woods such as Cedar, Redwood and exotic

hardwoods. In just 10 minutes, Deck & Fence Brightener, a

chlorine-free formula, deep cleans without damaging the wood’s

cell structure or leaving a bleached out look. It also removes

residual traces of old water sealers from weathered wood and

invisible coating barriers such as “mill glaze” from new Cedar,

enabling proper adhesion and penetration of protective sealers

and stains. The 100% biodegradable formula will not harm grass

or surrounding plant life.

.FEATURES .

 Eliminates mildew & algae stains, black tannin stains, mill

glaze

 Environmentally safe, acid-free, chlorine-free

 Restores wood to its natural look

 Prepares surface for sealing and staining

.PRODUCT .

SKU Description

16116 1-Gallon

.RECOMMENDED USES .

FOR EXTERIOR USE ONLY

Use Deck & Fence Brightener to prepare or restore outdoor

wood decks, porches, fences, siding, shakes & shingles, outdoor

furniture & décor, boat docks, boardwalks, gazebos & arbors,

play sets and more.

WOOD TYPES

Use on all types of wood including pressure-treated lumber and

tannin-rich woods such as Cedar, Redwood and exotic

hardwoods such as Mahogany, Teak, Ipé etc..

Note: New generation (non-CCA) pressure-treated lumber,

when initially installed may develop pronounced mildew growth

during the first few months of weathering. To reduce or avoid

mildew staining allow wood to weather for 1 to 3 months before

applying a protective coating. To immediately protect against

water damage, prep the surface with DeckBrite and pre-treat

with Wolman RainCoat

Oil-based Clear Water Repellent. Allow

6 months before applying a protective coating.

SURFACE PREPARATION

Before you start, pre-rinse grass, plants and scrubs surrounding

the wood structure to be cleaned. Cover any exposed aluminum

surfaces to prevent corrosion. Sweep away any surface dirt and

debris. If the surface is in direct sunlight and hot to the touch,

dampen with fresh water.

PRODUCT APPLICATION .

MIXING

Use in a well ventilated area and ONLY as directed. DILUTE

BEFORE USE. In a five gallon plastic bucket, combine one

gallon of concentrate with four gallons water to make five gallons

solution, enough to clean/prepare approximately 750 square feet.

Each gallon of solution cleans approximately 150 square feet. If

less than five gallons solution is needed use a plastic measuring

device to combine one part concentrate with four parts water. Stir

for one minute or until solution is thoroughly blended. Do not mix

with any other products.

APPLY

Make sure entire wood surface is dry and free of dust, dirt and

debris. If the surface is hot to the touch or in direct sunlight,

dampen with fresh water to cool. Apply when outside

temperature is above 40°F (4°C) and when 24 hours of

precipitation-free weather is expected. On a horizontal surface,

apply the mixture with a pump sprayer, brush or mop. On a

vertical surface (siding or fencing), apply with a pump sprayer or

deep-nap roller, working from the bottom to the top of the

structure. Work end-to-end on 5-10 boards (20 square foot

areas) at a time, in order to maintain adequate surface wetness

to allow concentration of the cleaning effort. Allow the solution to

sit for 10 minutes, keeping wet with more solution as needed.

SCRUB or PRESSURE WASH

Briefly scrub surface with Wolman Woodworx Deck Brush or

other stiff , short-bristle brush, using moderate pressure or

pressure-wash using a 40° tip and 1,500-2,500 psi for pressure-

treated wood and hardwood. Use 500-1,000 psi for Cedar and

Redwood. Move lengthwise with boards to avoid cut marks

across grain. Either technique helps ensure old surface is entirely

removed.

RINSE

If pressure washing is not employed, after brushing, rinse

thoroughly with a garden hose, using the highest nozzle

pressure setting available. When dry, surface should appear

clean, bright and free of mildew and algae stains. Heavily

weathered or badly stained areas may require a second

application.

CAUTION: Bare wood and/or coated surfaces can become

slippery when wet. Use caution when walking on wet surfaces.

COVERAGE

When mixed with water, one (1) gallon of liquid concentrate

makes five (5) gallons of solution, enough to cover approximately

750 square feet depending on wood age and species, surface

porosity, and method of application. One (1) gallon of solution

covers approximately 150 square feet.

DRY TIME

Allow the wood to dry thoroughly before applying a water-based

finish and at least 24 hours before applying an oil-based finish.

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA WOL-05 DECK & FENCE BRIGHTNER WOOD CLEANER & COATING PREP .DESCRIPTION AND USES PRODUCT APPLICATION . ® MIXING Wolman Deck & Fence Brightener Wood Cleaner & Coating Prep functions as two products. It is a cleaner for weathered wood and a pre-coating preparation for new or weathered wood. When mixed with water, Deck & Fence Brightener liquid concentrate quickly and safely restores dirty, weathered-gray, mildew and algae-stained wood to its natural, like-new look.
PAGE 2
TECHNICAL DATA DECK & FENCE BRIGHTNER WOOD CLEANER & COATING PREP HANDLING AND STORAGE . CLEAN UP Clean tools and equipment after use with water. Care should be taken to cover any exposed aluminum surfaces to prevent discoloration as this product is corrosive to metal. DO NOT MIX WITH ANY OTHER PRODUCT, especially those containing chlorine or bleach (sodium hypochlorite). Rinse plants with water after exposure. CAUTION: WOOD SURFACES MAY BE SLIPPERY WHEN WET. FOR EXTERIOR USE ONLY.
PAGE 3
TECHNICAL DATA DECK & FENCE BRIGHTNER WOOD CLEANER & COATING PREP PHYSICAL PROPERTIES . Physical Properties Liquid Concentrate Active Ingredient Weight pH Oxalic Acid Per Gallon 8.7 lbs. Per Liter 1.04 kg Concentrate 0.7-1.2 In Solution 1.0-2.0 Practical Coverage Depending on wood age and species, surface porosity and method of application, one (1) gallon of solution covers approximately 150 sq. ft.