Technical Specifications

T e c hn i c a i D a t a S hee t
Wolman Wood Care Products
ZINSSER Co., Inc. 2110 William Pitt Way, Bldg. #A6, Pittsburgh, PA 15238
D e ck S t r i p
®
S t a i n & F i n i s h R emo v e r
Description
Wolman
®
DeckStrip
®
Stain & Finish Remover
is a ready-to-use, premium quality, “universal” exterior
wood stripper for all types of traditional stains and
pigmented finishes. In just 15 minutes, DeckStrip will quickly
cut through and remove old, weathered coatings, including solid
or semi-transparent stains, tinted water repellents or other
toner-type, transparent finishes. Oil-base, water-base, and
even tough-to-remove latex stains are easily removed in
one application with the help of DeckStrip’s special wetting
agents and thickener for vertical surfaces. Once stripped, wood
is restored to its bright, clean, natural look. Using DeckStrip
before re-application of a protective finish or stain ensures its
proper adhesion, penetration and optimum performance.
Special Features
� Safer to Use – no methylene chloride or caustics.
� Contains Unique Wetting Agents – reduces the need for
multiple applications.
� Clings to Vertical Surfaces for effective stripping the first
time around.
� 100% Biodegradable - safe for grass, plants, and shrubs.
Recommended Uses
FOR EXTERIOR USE ONLY.
WOOD TYPES: Use on all wood types, including pressure-
treated lumber, Cedar, Redwood, exotic hardwoods (Mahogany,
Ipé, Teak, etc.), and North American hardwoods.
PROJECTS: Use DeckStrip to strip and restore outdoor wood
decks, fences, siding, shakes and shingles, boat docks &
boardwalks, outdoor furniture & décor, gazebos & arbors,
play sets and more.
Getting Started – Evaluating Wood Condition
Step 1 – Perform a Splash Test:
Prior to re-coating over previously coated wood, it is
important to determine if there is a surface barrier present which
would prevent the proper penetration or adhesion of a new
coating. To conduct a Splash Test, sprinkle several
handfuls of water on a few distinct areas of the surface. If
the water absorbs rapidly, the surface will accept a new coating.
If the water beads, puddles or is not absorbed in 10
minutes, an external coating “barrier” exists, and must be
eliminated before re-coating can begin.
Step 2 –Prepare and Restore the Surface:
Before applying a different semi-transparent stain or transparent
finish to a previously coated surface, it is necessary to
thoroughly remove any visible pigment from the prior coating,
plus any residual water repellency, which can act as a barrier to
the proper penetration/adhesion of the new coating. Select
and use Wolman DeckStrip if you have this WOOD
CONDITION, which is described in further detail below.
After stripping, repeat the Splash Test to confirm water
absorption.
Wood Condition:
Previously Coated, Weathered Wood –If an oil or latex
stain (solid, semi-transparent or wood-colored finish) is
present, whether in deteriorated or sound condition, use
Wolman DeckStrip
®
Stain & Finish Remover according to
label and Technical Data Sheet instructions to remove the old
coating. For lightly pigmented coatings that are fairly
weathered and barely visible, two options exist: strip with
DeckStrip or clean away with Wolman DeckBrite powder
concentrate or Deck & Fence Brightener liquid concentrate,
based on the particular wood type present. Paints and
acrylic stains will require use of a paint stripper.
Recommended Application Method
Homeowner/DIY’er:
On Horizontal Surfaces: A synthetic bristle brush or mop
is recommended.
On Vertical Surfaces: A synthetic bristle brush or deep-
nap roller is recommended. When applying, work from the
bottom to the top of the structure.
A pump sprayer (with no aluminum parts) may also be
employed, but Safe Handling directions detailed on other side
must be followed to avoid exposure to over-spray.
Professional Contractor:
On Horizontal or Vertical Surfaces: Apply solution with a
pump sprayer (no aluminum parts) or airless sprayer.
Safe Handling directions detailed on other side must be
followed to avoid exposure to over-spray.