P R O W A L L V E N T I L AT I O N H O O D S I NSTALLATION I NSTRUCTIONS
C O N TA C T I N F O R M AT I O N Wolf Customer Service: 800-332-9513 Website: wolfappliance.com As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equipment. There are two types of potential hazards that may occur during installation. signals a situation where minor injury or product damage may occur if you do not follow instructions.
W O L F P R O WA L L V E N T I L AT I O N H O O D S I N S TA L L AT I O N R E Q U I R E M E N T S IMPORTANT NOTE: This installation must be completed by a qualified installer or Wolf authorized service center technician. Installer: Please read the entire Installation Instructions prior to installation. Save these instructions for the local inspector’s reference, then leave them with the homeowner.
W O L F P R O WA L L V E N T I L AT I O N H O O D S Low-Profile Wall Hood L I S T O F M AT E R I A L S I N S TA L L AT I O N C O N S I D E R AT I O N S The following is a list of materials shipped with the Wolf Pro wall ventilation hood. Wolf Pro wall ventilation hoods are recommended for use with all Wolf cooking appliances.
I N S TA L L AT I O N I N S T R U C T I O N S I N S TA L L AT I O N C O N S I D E R A T I O N S IMPORTANT NOTE: Wolf recommends that the Pro wall ventilation hood be installed 30" (762) to 36" (914) above the countertop. Rail option (R) wall hoods come with a classic stainless steel decorative rail and stand-offs. Optional platinum or brass rails are available to match Wolf dual fuel range bezels. Contact your Wolf dealer for details.
W O L F P R O WA L L V E N T I L AT I O N H O O D S OV E R A L L D I M E N S I O N S L O W- P R O F I L E W A L L H O O D S 12" (305) 3/4" (19) Overall Widths DIAMETER OF RAIL 10" (254) 30" (762), 36" (914), 42" (1067) and 48" (1219) OVERALL 4" (102) HEIGHT 22" (559) OVERALL DEPTH OVERALL WIDTH 2" Overall Height 10" (254) Overall Depth (excluding rail) 22" (559) (51) Shipping Weight (shell only) Low-Profile Wall Hood shown with (R) rail option 39–55 lbs (18–25 kg) Unit dimensions may vary
I N S TA L L AT I O N I N S T R U C T I O N S I N S TA L L AT I O N S P E C I F I C A T I O N S Low-Profile Wall Hoods 6" LOCATION OF ELECTRICAL (152) E 5" (127) 10" (254) HEIGHT OF HOOD WIDTH OF HOOD 30" TO 36" (762–914) TO COUNTERTOP 30" TO 36" (762–914) TO COUNTERTOP 22" (559) DEPTH OF HOOD NOTE: Pro low-profile wall hoods have an adjustable discharge.
W O L F P R O WA L L V E N T I L AT I O N H O O D S T R A N S I T I O N S P E C I F I C AT I O N S Low-Profile Wall Hoods – 10" (254) Round Accessory Transition (in-line or remote blower) Model PW302210 (A) 30" (762) (B) (C) 9" (229) 14 3/4" (D) (375) 5 5/8" (143) (451) 5 5/8" (143) PW362210 36" (914) 9" (229) 17 3/4" PW422210 42" (1067) 9" (229) 20 3/4" (527) 5 5/8" (143) PW482210 48" (1219) 9" (229) 23 3/4" (603) 5 5/8" (143) The illustrations and chart provide dimensions spe
I N S TA L L AT I O N I N S T R U C T I O N S T R A N S I T I O N S P E C I F I C AT I O N S The illustration and chart provide dimensions specific to Pro 24" (610) and 27" (686) deep wall hood models. These dimensions are critical for proper installation.
W O L F P R O WA L L V E N T I L AT I O N H O O D S L OW- P R O F I L E W A L L H O O D S S T E P 1 : I N S TA L L D U C T W O R K DUCTWORK INSTALLATION THROUGH ROOF To reduce the risk of fire, use only metal ductwork. IMPORTANT NOTE: Wolf recommends that the Pro low-profile wall hood be installed 30" (762) to 36" (914) above the countertop. IMPORTANT NOTE: Consult a qualified HVAC Engineer for specific ducting applications.
I N S TA L L AT I O N I N S T R U C T I O N S L OW- P R O F I L E W A L L H O O D S S T E P 2 : W A L L P R E P A R AT I O N S T E P 1 : I N S TA L L D U C T W O R K Always install a roof or wall cap if you are not installing a remote blower. Connect 8" (203) or 10" (254) round metal ductwork to the cap and work back towards the hood. Use duct sealing tape on joints between ductwork sections. Local codes may require the use of a backdraft damper.
W O L F P R O WA L L V E N T I L AT I O N H O O D S L OW- P R O F I L E W A L L H O O D S If you are using WBLOWER-50INT, refer to installation instructions provided with the blower and follow instructions for horizontal and vertical discharge. Install the blower in the hood before mounting the hood to the wall. Remove the filters by pushing each filter up at the angle it is placed in, and rotate down. Remove the center filter first. Gloves should be worn to provide the proper grip when removing filters.
I N S TA L L AT I O N I N S T R U C T I O N S 2 4 " ( 6 1 0 ) A N D 2 7 " ( 6 8 6 ) WA L L H O O D S S T E P 1 : I N S TA L L D U C T W O R K DUCTWORK INSTALLATION THROUGH ROOF To reduce the risk of fire, use only metal ductwork. IMPORTANT NOTE: Wolf recommends that the Pro wall ventilation hood be installed 30" (762) to 36" (914) above the countertop. IMPORTANT NOTE: Consult a qualified HVAC Engineer for specific ducting applications.
W O L F P R O WA L L V E N T I L AT I O N H O O D S 2 4 " ( 6 1 0 ) A N D 2 7 " ( 6 8 6 ) WA L L H O O D S S T E P 1 : I N S TA L L D U C T W O R K DUCTWORK INSTALLATION THROUGH ROOF Always install a roof or wall cap if you are not installing a remote blower. Connect 10" (254) round metal ductwork to the cap and work back towards the hood. Use duct sealing tape on joints between ductwork sections.
I N S TA L L AT I O N I N S T R U C T I O N S 2 4 " ( 6 1 0 ) A N D 2 7 " ( 6 8 6 ) WA L L H O O D S IMPORTANT NOTE: The screws should be countersunk so that they are below flush. S T E P 2 : WA L L P R E PA R AT I O N Framing must be tied together to provide enough structural strength to support the weight of the hood and internal blower, if applicable. Construct the wood wall framing flush with the wall studs and centered in the location that the hood will be mounted. Finish the wall surface.
W O L F P R O WA L L V E N T I L AT I O N H O O D S 2 4 " ( 6 1 0 ) A N D 2 7 " ( 6 8 6 ) WA L L H O O D S S T E P 3 : H O O D P R E P A R AT I O N IMPORTANT NOTE: If a duct cover is to be used, follow instructions on page 18 before installing the wall hood. If you are installing a recirculating kit, refer to instructions included with the kit before installing the wall hood. IMPORTANT NOTE: Wolf recommends installing the internal blower to the back plate prior to mounting the hood.
I N S TA L L AT I O N I N S T R U C T I O N S 2 4 " ( 6 1 0 ) A N D 2 7 " ( 6 8 6 ) WA L L H O O D S S T E P 4 : R E AT TA C H B A C K P L AT E S T E P 5 : H O O D I N S TA L L AT I O N Follow these instructions to reattach the back plate to the wall hood: IMPORTANT NOTE: If a backsplash is to be used, it should be installed before the wall hood is mounted. Refer to instructions included with the backsplash.
W O L F P R O WA L L V E N T I L AT I O N H O O D S D U C T C OV E R I N S T A L L AT I O N ACCESSORIES Optional accessories are available through your Wolf dealer. To obtain local dealer information, visit the Showroom Locator section of our website, wolfappliance.com. Installing a duct cover assembly will impact all aspects of the hood installation including hood location, ducting, electrical placement and the mounting surface.
I N S TA L L AT I O N I N S T R U C T I O N S E L E C T R I C A L WIRING This ventilation hood must be properly grounded. This unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes. Follow these instructions to install wiring for all Wolf Pro wall hoods: Run a 120 V AC, 15 amp circuit power cable from the service panel to the electrical box on the back plate. Run the conduit connector through the holes in the back plate.
W O L F P R O WA L L V E N T I L AT I O N H O O D S F I LT E R I N S TA L L A T I O N WO L F N A M E P L A T E Follow these instructions to install filters and grease cups for Wolf Pro wall hoods: The Wolf logo nameplate does not come installed on the hood since there are various locations that the nameplate can be attached. Also, some customers prefer not to have a nameplate on their hood. Remove all packaging material from the filters and grease cups.
I N S TA L L AT I O N I N S T R U C T I O N S INTERNAL B L OW E R S Verify that the blower discharge aligns with the discharge cut-out in the back panel of the hood. B L O W E R I N S TA L L A T I O N IMPORTANT NOTE: Refer to the specific installation instructions provided with each internal blower for additional mounting and wiring instructions. Install the hood and blower assembly to the wall. Secure the power cord(s) without damaging or pinching while installing the hood.
W O L F P R O WA L L V E N T I L AT I O N H O O D S I N - L I N E A N D R E M OT E B L O W E R S Be sure that there is enough space for any transitions that may be needed between the blower and the connecting ductwork. For best performance, locate transitions nearest the blower. B L O W E R I N S TA L L A T I O N IMPORTANT NOTE: Refer to the specific installation instructions provided with each blower for additional mounting instructions.
I N S TA L L AT I O N I N S T R U C T I O N S I N - L I N E A N D R E M OT E B L O W E R S Plug the cord assembly into the receptacle located near the center of the hood shell. Refer to the illustration on page 21. Use the clips on the interior of the hood to keep excess power cord away from moving parts. BLOWER WIRING IMPORTANT NOTE: Refer to the specific installation instructions provided with each blower for additional wiring instructions.
W O L F P R O WA L L V E N T I L AT I O N H O O D S B L OW E R A S S E M B L I E S Wolf Pro wall ventilation hoods are shipped without the blower assembly. Wolf internal, in-line and remote blower assemblies are available as sales accessories through your Wolf dealer. ACCESSORIES Optional accessories are available through your Wolf dealer. To obtain local dealer information, visit the Showroom Locator section of our website, wolfappliance.com. IMPORTANT NOTE: Blower options vary with the cooking surface.
I N S TA L L AT I O N I N S T R U C T I O N S AC C E S S O RY K I T S R E C I R C U L AT I N G K I T S RECIRC30 (808223) – Must be used with WBLOWER-50INT (810991) for low-profile wall hoods and WBLOWER-60INT (810559) for 24" (610) deep wall hoods. RECIRC36 (808224) – Must be used with WBLOWER-50INT (810991) for low-profile wall hoods and WBLOWER-60INT (810559) for 24" (610) deep wall hoods. Dimensions in parentheses are in millimeters unless otherwise specified.
W O L F P R O WA L L V E N T I L AT I O N H O O D S TROUBLES H O OT I N G IMPORTANT NOTE: If the Pro wall ventilation hood does not operate properly, follow these troubleshooting steps: C O N TA C T I N F O R M AT I O N Wolf Customer Service: 800-332-9513 Website: wolfappliance.com Verify that power is being supplied to the ventilation hood. Check electrical connections to ensure that the installation has been completed correctly.
LEFT OUTER EDGE OF HOOD 27 BOTTOM EDGE OF HOOD CUT-OUT FOR LOGO PLACEMENT FOLD LINE FOR LOGO PLACEMENT
WOLF APPLIANCE, INC. 811504 7 / 2007 P. O . B O X 4 4 8 4 8 MADISON, WI 53744 800-332-9513 W O L FA P P L I A N C E .
