installation instructions
WOLF SEALED BURNER RANGETOP RISER KIT
INSTALLATION INSTRUCTIONS
808992 / Rev
A
/ May 2006
Riser Kit Model Numbers:
30'' Sealed Burner Rangetop Riser:
808520 - 5'' Stainless Steel Riser Kit
808521 - 10'' Stainless Steel Riser Kit
8
08522 - 20'' Stainless Steel Riser
with Shelf Kit
36'' Sealed Burner Rangetop Rise:
808523 - 5'' Stainless Steel Riser Kit
808524 - 10'' Stainless Steel Riser Kit
808525 - 20'' Stainless Steel Riser
with Shelf Kit
48'' Sealed Burner Rangetop Riser:
808526 - 5'' Stainless Steel Riser Kit
808527 - 10'' Stainless Steel Riser Kit
808528 - 20'' Stainless Steel Riser
with Shelf Kit
Riser Kit Contents:
QTY
PART NO./DESCRIPTION
1 Center Support Bracket
1 Riser Front Panel
1 Riser Back Panel
2 Riser Supports
25 (730239) Finishing screws (#8
x 3/8'' Modified Truss Screws)
4 (801099) 10-16 x 1/2'' Screws
4 (802332) Shoulder Screws
20'' Shelf only
NOTE: Depending on which kit is
being installed, some screws may
not be used and may be discarded.
PROCEDURE
Assembling Riser:
1. Lay front panel on work surface
cosmetic side down. Remove pro-
tective covering from back side of
riser front panel.
2. Attach side support legs inside of
riser front panel, using supplied
finishing screws (See Fig. 1 & 2).
3. Remove backing from double
sided tape on center support
bracket flanges (See Fig. 3).
4. Align center support bracket with
alignment holes on bottom of front
panel. Verify that center support
bracket aligns vertically prior to
adhering VHB tape to rear of
front panel.
NOTE: Proper alignment is impor-
tant prior to securing tape. Firmly
press tape to back side of
front panel.
5. Slide back panel inside of front
panel mounting flanges (See Fig.
3). Align back panel mounting
holes with center support bracket
mounting hole.
6. Continue installing finishing
screws along center support
bracket and front panel
mounting flanges.
Attaching Riser Assembly to Sealed
Burner Rangetop:
1. Verify all packing material has
been removed from riser assembly
and all packaging residues has
been cleaned from stainless
steel surface.
2. Remove island trim from sealed
burner rangetop by removing the
top screw on each side panel.
3. Slide riser side support legs inside
rangetop outer side panels until
bottom of riser assembly is flush
with side panel (See Fig. 4). Verify
that center support legs align with
mounting holes.
4. Attach riser support legs and
center support to rangetop
(See Fig. 5).
20'' Riser Shelf Installation:
1. Once riser assembly is installed
onto rangetop, attach 4 (2 on
each side) shoulder screws in
front panel assembly.
2. Remove protective packaging
material from shelf. Align keyhole
slots on back side of shelf assem-
bly with two shoulder screws on
Be sure to disconnect power to
sealed burner rangetop before,
installing riser assembly.
Riser component parts may
have sharp edges which could
inflict serious personal injury
.
Use care when handling.
right side of front panel and two
shoulder screws on left side of
f
ront panel assembly.
3. Slide shelf assembly into place
and tighten shoulder screws if
necessary (See Fig. 6).
Center Support Alignment Holes
Side Support
Front panel
Side Support
Figure 1
Center Support
Alignment Holes
Figure 2
Back Panel
Figure 3
Figure 4
801099
10-16 x 1/2”
Screw
801099
10-16 x 1/2”
Screw
730239
Finished Screws
Figure 5
SHOULDER
SCREWS
SHELF ASSEMBLY
KEYHOLE
SLOTS
Figure 6
808992_SealedBurnRangeRiseInstall_RevA_May06.qxp 11/29/2006 9:36 AM Page 1