User manual

ManualsBrandsWohler ManualsComputer equipmentAMP2-S8DA

AMP-S8 Series+ User Manual P/N 821640 Rev-B

Erase Preset (ErasePSet):

This is a menu command that allows the user to erase a stored preset. Pressing the ENTER Button will allow the user

to choose a preset to erase:

Choose PresetNumChoose PresetNum

Choose PresetNum

Preset1: Off AirPreset1: Off Air

Preset1: Off Air

The

L UP and L DOWN Buttons or R UP and R DOWN Buttons select from among the available presets. Once a preset

has been chosen by pressing the ENTER Button, the user will be warned that the preset will be erased:

ERASE PRESET?ERASE PRESET?

ERASE PRESET?

Preset1: Off AirPreset1: Off Air

Preset1: Off Air

Pressing the

ENTER Button will erase that preset. Pressing the ESC Button will not erase that preset. In either case,

control returns to the menu to choose another preset to erase:

Choose PresetNum Choose PresetNum

Choose PresetNum

Preset2: VTR #2Preset2: VTR #2

Preset2: VTR #2

Press the ESC Button to exit Setup Mode and return to Normal Operational Mode.

SDI Delay:

Changing the SDI Delay changes the latency of an SDI audio signal as it is de-embedded from SDI. This adjustment

allows precisely synchronizing an SDI audio signal to a video signal. To change SDI Delay, select SDI Delay and

then press the ENTERButton.

SDI Delay adjust screen display will indicate:

—

SetupSetup

Setup —

SDI Delay: 140 ms SDI Delay: 140 ms

SDI Delay: 140 ms

Step through settings using or Buttons, select 140 ms (for example). To accept, press the ENTER Button.

Press the Button to exit Setup Mode and return to Normal Operational Mode.

Surround Gain (Srnd Gain)

To change Surround Gain, select Srnd Gain and then press the ENTER Button.

Surround Gain adjust screen display will indicate:

—

SetupSetup

Setup —

Srnd Gain -3dB Srnd Gain -3dB

Srnd Gain -3dB

Step through settings using the or Buttons, select -9dB (for example). To accept, press the ENTER Button. To

exit without saving, press the ESC Button. Note that surround gain adjustments are only effective for downmixes

DM1 and DM2. In downmix DM3 the surround gain is fixed.

Startup:

The Startup entry within the Setup menu is used to determine the input, which is used by the unit at power up. When set

to Last Used, the unit will power up the same way that the unit was before power was interrupted. If the user needs the

unit to power up in Analog mode (for example), then user should select the Analog entry by stepping through available

entries using the or Buttons. Save the selection by pressing the ENTE Button. Press the E C Button to exit

Setup Mode and return to Normal Operational Mode.

Analog Output Preference (A-OutPref):

To change Analog Output Preference, select A-OutPref and then press the ENTER Button.

The Analog Output Preference entry within the Setup menu is used to determine how the Selected/Downmix

Analog Output Connectors (Item M, page 14) and Metered Analog Output Connector (Item K, page 14) on the rear

panel output the channel mix when the DM1, DM2, or DM3 downmix selections is enabled.

The default setting is Downmix, which outputs the channel mix with individual channel scaling (gain settings) intact as

determined by the selected downmix (DM1, DM2, or DM3). However, if Discrete is selected, then all channels within

the downmix are output from these connectors at full gain without scaling of the channels as determined by the selected

downmix. For example, the Center channel scaling is -3dB, and the Surround channel scaling is set in the Setup menu.

User Interface Function Guide

Setup Mode (Cont.)

Section 2: Operation