Wohler AMP2-S8DA : User manual : Page 29

29

AMP-S8 Series+ User Manual P/N 821640 Rev-B

Recall Preset (RCallPSet):

This is a menu command, allowing the user to recall a stored preset. Pressing the Button while this menu

is active will present the user with the option of choosing a preset to recall:

Choose PresetNumChoose PresetNum

Choose PresetNum

Preset1: Off Air Preset1: Off Air

Preset1: Off Air

Pressing the and Buttons will scroll through the presets, showing each one by name. In the above example, Preset

1 is called “Off Air”. If a particular preset is not assigned, it will be indicated as follows:

Choose PresetNumChoose PresetNum

Choose PresetNum

Preset7: Unused Preset7: Unused

Preset7: Unused

Pressing the

ENTER Button with the desired preset shown will recall that preset, so the system state will be now setup

according to that preset.

Save Preset (SavePSet):

Pressing the L UP and L DOWN Buttons or R UP and R DOWN Buttons will scroll up or down through the presets,

showing each one by name. If a particular preset is not assigned, it will be indicated as follows:

Choose PresetNumChoose PresetNum

Choose PresetNum

Preset7: UnusedPreset7: Unused

Preset7: Unused

Choosing an already used preset will display a warning to the user that they are about to overwrite the preset, as follows:

OVERWRITE PRESETOVERWRITE PRESET

OVERWRITE PRESET

Preset1: Off AirPreset1: Off Air

Preset1: Off Air

If the user presses the ENTER Button, a prompt appears asking if the user would like to save the old name with the new

preset as follows.

Save Old Name? Save Old Name?

Save Old Name?

Preset1: Off AirPreset1: Off Air

Preset1: Off Air

Pressing the ENTER Button keeps the old name for the new preset. Pressing the ESC Button results in a prompt for

a new preset name as follows:

AES1 ?@<A>BC AES1 ?@<A>BC

AES1 ?@<A>BC

Name: A_Name: A_

Name: A_

Select letters using the L UP and L DOWN Buttons or R UP and R DOWN Buttons. The current selectable character

appears between the < > symbols. Press the ENTER Button to accept the current letter and move to the next letter. Naming

will automatically end after eight characters are selected, or end naming by pressing the ENTER Button when the _DONE_

selection appears. The _DONE_ selection comes before the numerals, and follows the lower case alphabet. The character

order is the order of ASCII characters. Characters are cycled through in the following order (left to right, top to bottom):

“ # $ % & ` ( ) * + ,- . / 0 1 2 3 4 5 6 7 8 9 : ; < = > ? @ A“ # $ % & ` ( ) * + ,- . / 0 1 2 3 4 5 6 7 8 9 : ; < = > ? @ A

“ # $ % & ` ( ) * + ,- . / 0 1 2 3 4 5 6 7 8 9 : ; < = > ? @ A

B C D E F G H I J K L M N O P Q R S T U V W X Y Z [ \ ] ^ _B C D E F G H I J K L M N O P Q R S T U V W X Y Z [ \ ] ^ _

B C D E F G H I J K L M N O P Q R S T U V W X Y Z [ \ ] ^ _

` a b c d e f g h i j k l m n o p q r s t u v w x y z { | } ~` a b c d e f g h i j k l m n o p q r s t u v w x y z { | } ~

` a b c d e f g h i j k l m n o p q r s t u v w x y z { | } ~

Upon completion of naming the preset, the current state of the system is saved under that name and preset number.

At any time during this process the user may press the Button and the preset will not be saved and the unit

will return to Normal Operational Mode.

Preset Mode Enable (PSetMode):

This is an alternative mode of operation. In Preset Mode, the INPUT Button cycles through the defined Presets.

With Preset Mode enabled, the user can approach the unit and press only the INPUT Button to access each stored

preset by name, rather than by signal type.

User Interface Function Guide

Setup Mode (Cont.)

Section 2: Operation