User manual

ManualsBrandsWohler ManualsComputer equipmentAMP2-S8DA

AMP-S8 Series+ User Manual P/N 821640 Rev-B

R DOWN (ENTER) Button

Selection Navigation Using the UP and DOWN Buttons: > R DOWN (or R UP) Button

The R DOWN or R UP (and L DOWN or L UP) Buttons are used to cycle through and select different channels or

channel combinations, depending on which Selection Mode is selected. See Single Channel Selection, Paired Channel

Selection, and Downmix Selection on page 25 for more information about using these buttons for channel selection.

Using the ENTER Button:

When in Setup Mode, The ENTER Button and is pressed to accept menu selections. Also see Enabling Setup Mode

(page 28) and the Setup Menu Navigation Flow Chart (Figure-2e, page 31) for more detailed information.

R UP (ESC) Button

Selection Navigation Using the UP and DOWN Buttons: > R UP (or R DOWN) Button

The R UP or R DOWN (and L UP or L DOWN) Buttons are used to cycle through and select different channels or

channel combinations, depending on which Selection Mode is selected. See Single Channel Selection, Paired Channel

Selection, and Downmix Selection on page 25 for more information about using these buttons for channel selection.

Using the ESC Button:

In Setup Mode, the ESCButton is used to exit, or back out of, any of the menus within Setup Mode without accepting

changes. Also see Enabling Setup Mode (page 28) and the Setup Menu Navigation Flow Chart (Figure-2e, page 31)

for more detailed information.

DM3 SD.SDI2 DM3DM3 SD.SDI2 DM3

DM3 SD.SDI2 DM3

GP1 GP2GP1 GP2

GP1 GP2

1 3 5 71 3 5 7

1 3 5 7

2 4 6 82 4 6 8

2 4 6 8

Source Status

(SD-SDI Input 2)

SDI Group

(Group #2)

Input Lock Status

(Channels 1, 2, 3, 4,

5, 6, 7, 8 Locked)

Mix Status

(Downmix

DM3)

SDI Group

(Group #1)

Mix Status

(Downmix

DM3)

LCD Display

In Normal Operational Mode the high-contrast LCD Display is used to report the currently selected channels for

reproduction along with selected source type, mix type, and any SD/HD-SDI audio group information (for products with

the SDI inputs). In other modes the display will indicate phase correlation and mute status. In Setup Mode, the display is

used to navigate menus, select parameters, and recall and name presets.

In normal operation (not muted), the Input Lock Status indicator (center of second line in display) is used to show the lock

status of selected digital inputs (including SDI sources). If all four input channel pairs are not locked (or connected), then

four short dashes are displayed in the center of the second line of the display. Each dash (-) indicates a position for

displaying the channel pairs available for monitoring. The display appearance and order (from left to right) is: 1/2, 3/4, 5/6

and 7/8. The input status is updated whenever a change in status is detected. The Input Lock Status is active only if one

of the digital sources is selected via the INPUT Button (Item 7i), and applies only to the digital source that is selected.

Status Display Examples - Input Sources:

User Interface Features

Section 2: Operation

MIX HD.SDI1 MIXMIX HD.SDI1 MIX

MIX HD.SDI1 MIX

GP3 -- GP4GP3 -- GP4

GP3 -- GP4

5 75 7

5 7

6 86 8

6 8

Source Status

(HD-SDI Input 1)

SDI Group

(Group #4)

Input Lock Status

(Channels 1, 2, 3, 4 Not

Locked; Channels 5, 6, 7, 8

Locked)

Mix Status

(Custom)

SDI Group

(Group #3)

Mix Status

(Custom)