OPERATING INSTRUCTIONS 072012 ORDER NO.: 00242_VL2 GB Original instructions RN10 VL-2 A/S Wodschow & Co. Industrisvinget 6 DK-2605 Brøndby Denmark Phone: +45 43 44 22 88 Telefax: +45 43 43 12 80 www.bearvarimixer.com info@wodschow.
Contents: General: . ..................................................................................................................................................................... 2 Safety: . ..................................................................................................................................................................... 2 Installation of new mixer:....................................................................................................................
VL2 control panel - survey of various operating situations: The following pictures show various operating situations and corresponding explanation: 2 1 Emergency stop is activated - there is no light in the display. If the red diode at is flashing, the mixer has stopped because the safety circuit has been interrupted, either because the bowl arms have been lowered or the safety guard has been opened.
Operation of the mixer: Text field (timer) Fixed speeds Speed indicator Time down Speed up REMIX-function Time up Start/Stop Speed down Emergency stop Pause Indication of operation time: Before starting the mixer: Mount the required tool in the bayonet shaft. Place the bowl in the bowl arms and raise it to its working position by means of the handle for bowl lift. Close the safety guard. The mixer is ready for start.
The Remix function: Reset of timer: The special Remix-function is a shortcut to programming of recipes. While the mixer is operated, all commands are stored, and when a recipe is finished and is pushed, it is possible to store the entire recipe under a program number. The timer can be reset by simultaneously pushing and . If the timer is reset while the mixer is running, the mixer will stop. • There are four program numbers. • A program cannot be deleted, but can be replaced.
Construction of the mixer: Bowl lift Attachment drive Machine label Poly V belt Planetary head Bayonet socket Motor Bowl lift arms Frequency converter The maximum capacity of the mixer: Capacities per mix Tool RN10 Egg white Whip 1L Whipped cream Whip 2,5 L Mayonnaise * Whip 8L Herb butter Beater 5 kg Mashed potatoes * Beater/Whip 3,5 kg Bread dough (50%AR) ** Hook 5 kg Bread dough (60%AR) Hook 6 kg Ciabatta dough * (70%AR) Hook 5,5 kg Muffins * Beater 6,5 kg Layer cak
Correct use of tools: Recommended max. speeds for attachment drive: Recommended applications for tools: Whip Beater Hook Cream Cake dough Bread dough Egg whites Butter cream Dark bread Mayonnaise Waffle dough and the like and the like Minced meat and the like Whips should not be struck against hard objects as e.g. the edge of the bowl. This will make the life of the tool shorter due to increasing deformity. For production of mashed potatoes use first the beater and then the whip.
VL-2 control, error codes and possible solutions: Error codes and possible solutions: The VL2 control will in case of certain errors show an error code in the display: Too high temperature in the frequency converter. Solution: Switch off the mixer and let it cool down. Wrong voltage of power supply. Solution: Compare the voltage indicated on the machine label with the power supply. The motor has been constantly overloaded for a long period of time. The load has been between 100 - 150% of maximum load.
Test programs: To enter the test mode of the mixer, do as follows: Raise the bowl and close the safety guard, push emergency stop. Hold and and release the emergency stop at the same time. Now go through four test programs: Test program 1: Test of fields. Press to activate test program no. 1 OBS. The fields must be activated in the following order: Briefly push the following fields – – – – – – – – – – . The mixer will now automatically run the next three test programs.
Service instructions: Before a possible repair or adjustment, the power must be switched off by dismantling the connection cable from the power supply. 5A 5B 3B 3C 6D 13C 6 6E 6A 6B 6C 6E 2 13A 13B 5C 3 1A 5 1 4B 4A 4 3A 7 3D 8B 8 8A 11 The mixer is to be bolted on to the table with 4 pcs. M6 bolts. The length of the bolts must be 90 mm + the thickness of the table top.
1 Take off the rear part by removing the 2 screws (1A) 2 The lid of the mixer can be taken off when the rear part (1) has been removed. Push the lid a little backwards, and lift it free. 3 Take off the operation panel by removing the rubber gasket (3A) and the thumb screw (4A) on the attachment drive. Remove the nut (3B) and loosen the 2 screws (3C). The screws must still grab the two fittings (3D) which are to be lifted up together with the screws.
10B 10A 10 10 Take out the planetary head in the following way: a) Take off the lid of the mixer (2), the operation panel (3), the attachment drive (4), the Poly V-belt (6) and the planetary head pulley (6D). b) Remove the locking ring (10A), and the planetary head can now be loosened by hitting the shaft (10B) with a plastic hammer. Take care not to drop the planetary head.
12 Exchange the micro switch for bowl lift in the following way: a) Take off the cover plate (8A) on the back of the mixer. b) Take out the frequency converter (8) with fittings (8D). c) The bowl lift micro (12) with fittings (12A) can be taken out by loosening the two screws (12B) and removing the two wires. The micro can not be exchanged. d) Mount the new micro switch by following the instructions in reverse order. No adjustment is required.
Black Green Yellow White Blue Red Safety guard CE micro RN20-194.28M rev 02 Thermoswitch in motor RN20-194.27M rev 02 RN20-194.26M rev 03 2 - blue 3 - blue 4 - black 2 - blue 3 - blue 4 - black Orange Orange Red Red Brown Brown Motor CE-micro Termoswitch CR10-194.17M rev 00 Thermoswitch 2 - brown 1 - brown 1 - green/yellow 2 - white 3 - black 4 - red CR10-194.15M rev 00 RN20-194.
1 - Red 2 - Blue 3 - White 4 - Yellow 5 - Green 6 - Black Red Blue White Yellow Green Black 1 2 3 4 5 6 1 2 3 4 5 6 Red Blue White Yellow Green Black 1 2 3 4 5 6 1 2 3 4 5 6 Screen Red Blue White Yellow Green Black 1 - Red 2 - Blue 3 - White 4 - Yellow 5 - Green 6 - Black Orange Orange 1 1 Orange Orange 6 - Brown (T2) 5 - Red (bowl) 4 4 2 2 5 5 3 3 CE/Bowl 6 6 4 - Black (safety guard) 3 - Blue (T1) 2 - Red (bowl) 1 - Orange (safety g
Handle for bowl lift can be mounted in both sides of the mixer: The handle for bowl lift as well as cover plug and a hexagon spanner are placed in the bowl of the mixer. The handle can be mounted either in left or right side of the mixer - the big cover plug is to be put into the hole on the opposite side of the mixer. Handle for bowl lift 1. Mount the key in the handle. 2. Place the handle with key on the mixer so that the handle points forward. 3.
Indhold af CE Overensstemmelseserklæring, (Maskindirektivet, 2006/42/EC, Bilag II, del A) Contents of the EC Declaration of conformity for machinery, (Machinery Directive 2006/42/EC, Annex II., sub. A) Inhalt der EG‐Konformitätserklärung für Maschinen, (Richtlinie 2006/42/EG, Anhang II, sub A) Contenu de la Déclaration CE de conformité d’une machine, (Directive Machine 2006/42/CE, Annexe II.
Innehåll i EG‐försäkran om maskinens överensstämmelse, (Maskindirektivet 2006/42/EG, bilaga 2, A) Contenuto della dichiarazione CE di conformità per macchine, (Direttiva 2006/42/CE, Allegato II, parte A) Sisukord EÜ masina vastavusdeklaratsioon , (Masinadirektiiv 2006/42/EÜ, lisa II, punkt A) Treść Deklaracja zgodności WE dla maszyn (Dyrektywa maszynowa 2006/42/WE, Załącznik II, pkt A) Sisältö EY‐vaatimustenmukaisuusvakuutus koneesta (Konedirektiivi 2006/42/EY, Liite II A) Tillverkare; Fabbricante; Toot
A/S WODSCHOW & CO. Industrisvinget 6 DK-2605 Brøndby Denmark Phone: 43 44 22 88 Telefax: 43 43 12 80 info@wodschow.dk www.bearvarimixer.
