User manual WMF 1000 S and WMF 1000pro S coffee machines EN - Type 03 0500 (WMF 1000 S), Type 03 0510 (WMF 1000pro S)
Preliminary comments Congratulations on choosing your new WMF coffee machine. WMF has been involved with the preparation of coffee for more than 125 years. Innovation, quality and many years of experience characterise WMF as a manufacturer of professional premium coffee machines. The WMF 1000pro S and WMF 1000 S bring this quality coffee into your home. Read this user manual before you start preparing the coffee.
Legend 1 Bean container lid 2 Lid for ground coffee insert 3 Brewing unit lid 4 Hot water button 5 Hot water spout 6 Milk hose 7 Water tank 8 Drip tray with drip tray grid Preheat cup Steam Jet WMF 1000 S 9b Preheat cup Steam Jet WMF 1000pro S 10 WMF All-In-One spout 9a 11 Coffee grounds container 12 Beverage buttons 13 Function keys 14 Display 15 Cup storage Leave this page folded out while reading the user manual.
Ready-to-operate display The descriptions in this user manual are always based on the assumption that coffee machine is ready to operate. When the following display appears (item 14) your machine is ready for use and you can now select your hot drink: your selection please 8:15 1.3.
The hot water button The hot water button is located on the right hand side at the front on the machine (item 4).
Overview of highlights of the WMF 1000 S and WMF 1000pro S The following functions make the WMF coffee machine unique: Unique variety of beverages and pot function The coffee machine makes (2x) Espresso, Ristretto, (2x) Cafe Creme, (2x) Cappuccino, Cafe Latte, Espresso Macchiato, Milk, milk foam, hot water for tea and even a full pot of Cafe Creme. On the WMF 1000pro S there are two Latte Macchiato at the same time.
Table of contents 1 1.1 1.2 For your safety . . . . . . . . . . . . . . . . . . . 1 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . 1 Hazard instructions . . . . . . . . . . . . . . . . . . . . 2 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 Initial setup . . . . . . . . . . . . . . . . . . . . . . 5 Scope of supply . . . . . . . . . . . . . . . . . . . . . . . 5 Installation and connection . . . . . . . . . . . . . 7 Testing the water hardness. . . . . . . . . . . . . . 9 Clean the water tank . .
For your safety 1 For your safety Maximum possible safety of devices is one of the characteristics of WMF products to which we give our special attention. The integrated safety devices of the coffee machine are, however, only effective if you follow the following safety instructions. 1.1 Intended use The WMF 1000 S and the WMF 1000pro S are coffee machines for Espresso, Café Crème and Ristretto, and the milky coffee specialities Cappuccino, Latte Macchiato, Cafe Latte and Espresso Macchiato.
For your safety 1.2 Hazard instructions Despite all safety precautions, there is a hazard potential associated with each device if handled improperly. Therefore, follow the instructions below when handling your automatic coffee machine to avoid injuries and health hazards: Hazard! Possible injuries due to the grinders! As long as your automatic coffee machine is switched on and connected to the power supply, the grinder of your automatic coffee machine can start up and you may suffer injury.
For your safety Hazard! Probable risk of burns or scalding due to hot components or steam and hot liquids! The All-In-One spout and the hot water spout are very hot while in operation and on contact can cause burns. Hot beverages and escaping steam can scald you. > Do not touch the All-In-One spout, the hot water spout or the direct adjoining surfaces of your automatic coffee machine. > Avoid contact with the escaping steam and handle the hot beverage with care.
For your safety Hazard! Possible health hazard due to cleaning agents or descaling agents. Cleaning agents and descaling agents are irritants and become very hot while executing the cleaning programmes. Cleaning agents and descaling agents can affect your health. Cleaning agents and descaling agents can damage the plastic parts of the automatic coffee machine and other articles and textiles. > Use only the WMF cleaning agents and descaling agents.
Initial setup 2 Initial setup Now you are only few steps away from preparing and enjoying the perfect coffee. In this chapter, you can learn step-by-step how you can start operating yourcoffee machine. 2.1 Scope of supply > Check the scope of supply for completeness.
Initial setup Key to scope of delivery 1 Coffee machine 6 Milk hose with milk spout 2 WMF Milk system cleaner 7 Mains cable 3 User manual Accessories in plastic bag: Ancillary sheet Guarantee and Service 8 Multitool Service certificate 9 WMF cleaning tablets Supplementary sheet for care instructions 10 Small cleaning brushes 4 Carbonate hardness test 5 Water filter cartridge with adapter 11 12 Steam nozzle (replacement part) Brown milk nozzle for refrigerated milk (pre-assembled) T
Initial setup 2.2 Installation and connection > Unpack the automatic coffee machine. > Check the machine for possible damages during transportation. Assembly > While installing the automatic coffee machine, follow the hazard instructions given under chapter “1.2 Hazard instructions” on page 2 and in this chapter as well as the following instructions: > Place the automatic coffee machine on a stable, horizontal surface that is waterproof and heat-resistant.
Initial setup Installation Drip tray and drip tray grid insert > > > > > Remove the cover from the cable compartment and remove the cable (a). Plug the cable into the socket on the machine (b). Place the cable through the opening in the cover. Close the cable compartment. Connect the plug to an earthed socket. > Insert the drip tray (8a) with drip tray grid (8b) in the coffee machine.
Initial setup 2.3 Testing the water hardness > Briefly dip the provided Carbonate hardness-test strips (about 1 Second) into your tap water. One minute later, you can read the degree of hardness with the help of the colour scale on the test strip package. Enter the value with the initial settings (Chapter 29 Initial settings). 2.4 > > > > 9 Clean the water tank Remove the water tank (7) from the coffee machine. Remove all the accessories from the water tank.
Initial setup 2.5 Insert the WMF water filter The WMF water filter protects the coffee machine from scale formations and ensures best quality of water for making coffee. There is no need for a water filter if the water hardness range is between 0 and 4. If you insert a water filter, set the coffee machine accordingly (see „water filter being used?“ on page 16). > Remove the sieve (7a) from the water tank (7). > Pull the locking device (7b) of the cartridge adapter upwards.
Initial setup 2.6 Installing milk hose In the as-delivered condition, the milk hose (6) hangs from the All-In-One spout and is packed in a plastic bag. The water tank must remain outside the machine when fitting the milk hose. > Push the All-In-One spout to the lower position. > Insert the milk hose (6) into the guide (6d). Hazard! Possible danger of scalding caused by incorrect fitting of the milk hose If the milk hose is incorrectly fitted it may jump out of the guide.
Initial setup 2.7 Filling the water tank Caution! Possible damage to your automatic coffee machine due to unsuitable liquids! Liquids other than drinking water can damage your coffee machine or can result in clogging. > Fill the water tank of your automatic coffee machine only with clean, cold drinking water. > Never fill the water tank with hot water, mineral water, soda water, milk or other liquids. > Fill the water tank with cold tap water (maximum 2.8 litres).
Initial setup Hazard! Possible injuries due to the grinders! As long as your automatic coffee machine is switched on and connected to the power supply, the grinder of your automatic coffee machine can start up and you may suffer injury. > Do not reach into the coffee bean hopper of your coffee machine when the coffee machine is not switched off and removed from the mains.
Initial setup 2.9 Initial setting > Push the off/c button. The commissioning program begins. Set the language language: english OK: P change: -/+ initial setting of your WMF 1000 S initial setting of your WMF 1000pro S Set the switch off time sw. off time: 30 min OK: P change: -/+ > Set the desired language with – or + . > Confirm the language with P button. The setup programme now guides you through the initial settings.
Initial setup Energy saving modes Eco-Mode: 2 OK: P change: -/+ You can choose between 4 energy saving modes. > Please note the following information. > Using the – or + , set the energy saving mode. > Confirm your selection with P button. Energy saving mode Method of operation of the coffee machine 1 Both heaters are continuously ready for use. Coffee, milk, milk foam and hot water can be dispensed without having to wait. 2 (Factory setting) Hot water is held at operating temperature continuously.
Initial setup Set the time time hh:mm OK: P change: -/+ > Set the current time with Set the date date dd:mm:yyyy OK: P change: -/+ > Set the current date with Setting water hardness Is water filter being used? water hardn.: 13-16 OK: P change: -/+ water filter: No OK: P change: -/+ – or + (hh = hours in two digits, mm = minutes in two digits). > Confirm the time with P button. – or + (dd = day in two digits, mm = month in two digits, yyyy = year in four digits). > Confirm the date with P button.
Initial setup Rinsing the water filter place 3L container under h. w. spout heating up ... 17 > Place a collecting vessel with approximately 3 litres capacity under the hot water spout. While rinsing the filter, unusual noises are heard. This is normal. The noises end during the filter rinse. > Fill the water tank with cold tap water. > Place the lid on the water tank. > Slide the water tank gently into the automatic coffee machine. The machine subsequently heats up as shown in the display.
Initial setup At the end of the setup program, a test brew is carried out. The Espresso button blinks. > Place an appropriate drinking vessel under the All-In-One spout. > Press the Espresso button. The test brewing starts. During this test brewing, coffee grinder is filled with coffee beans. > Throw this first cup of coffee away. your selection pls 8:15 E2 1.3.2011 The coffee machine is now ready for operation. The selected Energy saving mode, for example “E2”, is displayed.
Operation 3 Operation In this chapter, you can learn everything about the easy method of coffee preparation with the coffee machine and how you can individually customize your coffee machine - entirely according to your preference! Hazard! Possible risk of burns or scalding due to hot components or steam and hot liquids! The All-In-One spout and the hot water spout are very hot while in operation and on contact can cause burns. Hot beverages and escaping steam can scald you.
Operation 3.1.1 Switching on WELCOME WMF 1000 S From switch on to operational readiness in about 3 minutes > Push the off/c button. WELCOME WMF 1000pro S heating up... your selection pls 8:15 1.3.2011 Your coffee machine heats up and performs coffee system rinse. This warms up all the pipes. > Place a collecting vessel (approx. 120 ml) under the All-in-One spout for the rinsing water. The coffee system rinsing procedure lasts for about. 40 seconds.
Operation 3.1.2 Switching off > Push the off/c button for at least 2 seconds. Before switching off, an automatic coffee system rinse is performed. If beverages are prepared with milk, then you are requested to perform a milk system rinse. > Follow the display instructions for a milk system rinse. The machine switches off. 3.1.3 Timer operation (automatic switch-on) timer OK: P change: -/+ 21 With the timer, you can automatically switch the coffee machine on or off.
Operation timer 8:15 1.3.2011 Manual switch on and switch off for timer operation The display shows the switch-on time that has been set. The current date and time is displayed, if these are activated in the basic settings. The button P -blinks. By pushing the P button you can change the switch-on time, without having to start the machine. The machine automatically switches on at the set time. > In order to manually switch the WMF 1000 S/WMF 1000pro S on in timer mode, briefly push the off/c button.
Operation 3.2 Use milk Milk is a very sensitive foodstuff. Always ensure cleanliness when using milk. Open the packing only with clean hands and tools. Always ensure that the milk is germ-free. We recommend that milk always be stored in a refrigerator and removed from it only for immediate use. > Place the refrigerated milk on the right, next to the machine. 3.2.1 With the milk nozzle (only on WMF 1000 S) On the WMF 1000 S use the milk with the milk nozzle.
Operation 3.2.2 With the milk lance On the WMF 1000pro S use the milk with the milk lance. The milk lance is included with the delivery. You can also use the milk lance on the WMF 1000 S as an alternative. Ask your dealer or order the milk lance from www.wmf.de. When using the WMF milk lance, the milk hose remains outside the milk container. You can store the milk lance together with the milk container in the cooler after use. This means that the milk lance remains in the milk container.
Operation 3.3 Preparing beverages In this chapter you will discover how to prepare your beverages at the touch of a button and how you can fine tune your taste experience with the comfort functions of the control panel. The way to make coffee beverages is described in Chapter 3.3.1 on page 26. The way to adjust the volume of the next beverage is described in Chapter 3.3.2 on page 28. The way to make coffee beverages is described in Chapter 3.3.1 on page 29.
Operation 3.3.1 Coffee specialities at the touch of a button > Place an appropriate drinking vessel under the All-In-One spout. > Adjust the All-In-one spout to suit the height of the drinking vessel. > Select your beverage by pressing the beverage button. You can interrupt the beverage preparation at any time using the off/c button. Espresso, Café Creme > If you want an Espresso, push the top left button. > If you want a Café Crème, push the top right button.
Operation Cappuccino, Latte Macchiato > If you want a Cappuccino, push the bottom left button. > If you want a Latte Macchiato, push the bottom right button. 1 x briefly: 1x Cappuccino 1 x briefly: 1x Latte Macchiato 2 x briefly: 2x Cappuccino 2 x briefly: 2x Latte Macchiato 1 x long: 1x Cafe Latte 1 x long: 1x Espresso Macchiato The name of the chosen beverage appears on the display. The coffee beans are ground. The selected beverage is prepared.
Operation 3.3.2 Quick selection of cup size The volume of the next cup can be stipulated before starting to prepare the beverage. The taste will therefor remain the same. You set the size of cup for the next beverage using the cup size rapid selection. You can also change the permanent setting of the cup size. See Chapter “3.6.1 Permanent setting of the cup size” on page 35.
Operation 3.3.3 Cup warming WMF Steam-Jet The WMF Steam-Jet finally sees the end of cold coffee cups. At the push of a button, hot steam flows slowly from below into the drinking vessel - to ensure coffee enjoyment at exactly the right temperature! Hazard! Possible danger of burns! Hot steam is delivered and the drinking vessel can get very hot! > Do not use the cup warmer without a drinking vessel and never without the drip tray in place. > Use heat-resistant drinking vessels.
Operation cup preheater ATTENTION! hot! Hot steam slowly flows from below into the drinking vessel. The flow of steam ends automatically when the button is released, latest however after 8 seconds. your selection pls 8:15 1.3.2011 Your automatic coffee machine is now ready for operation. 3.3.4 Pot function Using the pot function you can make a full pot of Café Crème. > Press the cup size rapid selection button for longer than 2 seconds. > Press + 2x briefly. The Cafe Creme beverage button lights up.
Operation 3.3.5 Set the coffee strength for the next beverage Prior to each coffee preparation, you can decide on the desired strength of your next coffee speciality. > Set the desired coffee strength with – or + . Following coffee strengths are available for selection: - Mild (about 15 % weaker than the saved setting) - Normal (corresponds to your setting) - Strong (about 15 % stronger than the saved setting) 3.3.
Operation > Place an appropriate drinking vessel under the All-In-One spout. > Open the lid of the ground coffee hopper (2). The display notifies: insert coff. grounds select beverage Cup volume: max. 15 g > Pour the ground coffee (adequate for a brewing cycle of about 9 g) in the ground coffee insert (2a). > Close the lid (2). > Select your beverage using the beverage buttons (one cup). The procedure can be cancelled with the off/c button.
Operation 3.3.7 Preparing milk and milk foam The coffee machine prepares hot milk and milk foam at the touch of a button. Non-foamed hot milk: > Place an appropriate drinking vessel under the All-In-One spout. Slide the All-In-One spout to the top position. If you forget this step on the WMF 1000 S, you will be reminded by the display. > Briefly press the milk button. A mug of hot milk is prepared. After the milk is dispensed, the All-in-One spout shall again be pushed slightly downwards.
Operation 3.3.8 Hot water dispensing You can dispense hot water, for example, for tea, with the help of Hot Water function. > Place a suitable drinking vessel under the hot water spout. > Briefly press the Hot Water button to obtain one glass of hot water. For obtaining hot water in variable quantities: > Press and hold the Hot Water button till the desired quantity of hot water is prepared. 3.4 Cancel beverage preparation You can cancel the current beverage dispense: > Push the off/c button.
Operation > Your WMF 1000 S/1000pro S switches off automatically after 30 minutes. Reduce the automatic switch off time (“Set the switch off time” on page 14). > Descale your WMF 1000 S/1000pro S regularly. Scale residues will lead to increased energy consumption. (Chapter “4.2.6 Descale coffee machine” on page 61). 3.6 Carry out the settings By setting the Cup size, you can adjust the quantity of the beverage for your cup size (Chapter. “3.6.1 Permanent setting of the cup size” on page 35).
Operation If you wish to adapt the volume of the next beverage delivery, proceed as per chapter “3.3.2 Quick selection of cup size” on page 28. If you wish to permanently change the volume to suit your cup size, proceed as follows: Press Select the cup size P button. select program browse: + cup size OK: P change: -/+ > Browse with + for basic settings. > Confirm your selection with P .button.
Operation cup volume: 100% OK: P Test:beverage cup > If necessary, carry out a test preparation (“Preparation test” on page 35). > Confirm the cup volume with cup volume: 100% OK: P change: -/+ 3.6.2 P button. > If necessary, change the cup volume. > Confirm the cup volume with P button. Beverage settings Here, the recipe for your coffee specialties are set according your personal coffee preferences.
Operation > Press Select the beverage setting P button. select program browse: + beverage settings OK: P change: -/+ > Browse with + for beverage setting. > Confirm your selection with P button. > Select the beverage for which you want to change the taste and the composition with the help of beverage buttons. Adjust the water volume water volume: 35 ml OK: P Test:bev.btn. > Set the desired water volume with – or + . > If necessary, carry out a test preparation (“Preparation test” on page 35).
Operation foam volume: 14 sec. OK: P change: -/+ The setting is applicable for coffee beverages with milk or milk foam. > Set the desired coffee strength with – or + . The volume of foam depends on the type of milk, the temperature of the milk and the milk nozzle being used. > If necessary, carry out a test preparation (“Preparation test” on page 35). > Confirm the foam volume with P button. milk volume: 28 sec. OK: P change: -/+ The setting is applicable for coffee beverages with milk or milk foam.
Operation sequ.: coffee-milk OK: P change: -/+ Pre brew: on OK: P change: -/+ Pre brew > Set the sequence of dispensing coffee and milk with – or +. > Confirm the sequence with P button. Pre brew: Before brewing, the ground coffee is dampened with hot water. This causes the ground coffee to swell up and the aroma of many types of coffee can develop better. > Set the pre brew function on or off with – or + . > If necessary, carry out a test preparation (“Preparation test” on page 35).
Operation grinding adjustment OK: P change: -/+ > Use the button + to scroll to grinding grade adjustment > Confirm the selection with P . Automatic coffee system rinsing starts. brewing test test grinding grade A brewing test starts directly and the grinding grade is checked. > Place a drinking vessel under the All-in-One spout. A decisive factor for the aroma is also the brewing pressure that is produced in combination with the grinding grade.
Operation grinding grade OK test: P end: C grinding too coarse test: P end: C If the grinding grade is set correctly, the brewing pressure is in the optimum range. The message “Grinding grade OK” appears. > Then confirm the grinding grade setting with off/c. If necessary, the grinding grade can be adapted to suit. If the grinding grade is too coarse, the coffee will run out quickly, the cream is light in colour and small in volume and the aroma is flat. The message “Grinding grade too coarse” appears.
Operation grinding too fine test: P end: C If the grinding grade is too fine the delivery stream is irregular, flow problems can arise and the ground coffee blocks the sieve or brewing unit. The message “Grinding grade too fine” appears. > Adapt the grinding grade using the Multitool (see “Set the grinding degree” on page 44). > Place a drinking vessel under the All-in-One spout. > To test the new setting, push P . Two new brewing tests start one after the other.
Operation Set the grinding degree Caution! Possible malfunction due to false setting of the grinding grade! The setting of the grinding grade of your automatic coffee machine in idle mode can lead to the grinder being set too tight and cannot start. > Set the degree of grinding for your coffee machine only when the grinder is in operation.
Operation 3.6.4 Basic settings Following settings can be adjusted: Basic settings Language* Switch off time* Switch-on time Eco-Modes (energy saving mode)* Brewing temperature Illumination Office functions Warm up rinsing Time* Date* Display of time/date Water hardness* Water filter* Special information tone Contrast display Factory settings The basic settings marked with a * have already been set during the commissioning. However, you can subsequently change these values too.
Operation Automatic switch-on time Brewing temperature Basic setting: 92 °C Illumination basic settings OK: P change: -/+ > Confirm your selection with P . switch-on time: on OK: P change: -/+ > Set the pre brew function on or off with brewing temp. 92 °C OK: P change: -/+ > Set the desired brewing temperature with > Confirm your selection with P button. illumination: On OK: P change: -/+ – or + (chapter “3.1.3 Timer operation (automatic switch-on)” on page 21). > Confirm your selection with P .
Operation Office functions specially for the office offi ce functions OK: P change: -/+ 3rd beverage Level: yes OK: P change: -/+ milk beverages: yes OK: P change: -/+ Warm up rinsing 47 warm up rinsing: off OK: P change: - You can deactivate functions of the beverage buttons using the office settings, to make operation of the machine easier, particularly in an office environment. > Set the office functions with – or + . > Confirm your selection with P . The 3rd.
Operation Allow display of date/time? date / time: on OK: P change: -/+ > Set the display of date and time on or off with > Confirm your selection with P button. Sound sound: on OK: P change: -/+ > Switch on or off the sound by pressing the control keys and beverage buttons with > Confirm your selection with – P – or +. or + . button. Display contrast display contrast OK: P change: -/+ > Set the display contrast with – or + . > Confirm your selection with P button.
Operation Select the counters 3.7 Reading counter readings > Press P button. select program browse: + Counters OK: P browse: -/+ Allow display of the number of prepared beverages? Reset counters? 49 Espresso 269 browse: -/+ reset all counters No: C Yes: P > Browse with + for counters. > Confirm your selection with > Browse with – or + P button. to display the number of beverages prepared. > Reset the counters with P button. or > retain the counters with C button.
Care 4 Care The care of your coffee machine is especially important so that your coffee is always prepared perfectly. The display notifies you about how soon the coffee machine must be rinsed, cleaned or descaled. Only 10 seconds time are needed to clean the machine before you switch it off. 4.1 Care overview Steps for care Warm up rinse / Coffee system rinse Rinse milk system WMF Connect & Clean Care interval - Automatic for each switch on and switch off.
Care Steps for care Care interval Cleaning the coffee grounds container - According to the request in display (dependent on the number of brewings). Clean the water tank - weekly Empty drip tray - daily Clean the bean hopper - weekly Clean machine housing - weekly After 10000 brewings, it is recommended that the maintenance of the device be carried out by the WMF Servicecenter. An instruction appears in the display while switching on. The instruction is repeated after sometime. 4.
Care Hazard! Possible health hazard due to cleaning agents or descaling agents. Cleaning agents and descaling agents are irritants and become very hot while executing the cleaning programmes. Cleaning agents and descaling agents can affect your health. Cleaning agents and descaling agents can damage the plastic parts of the automatic coffee machine and other articles and textiles. > Use only the WMF cleaning agents and descaling agents. > Avoid any contact with cleaning agents or descaling agents.
Care 4.2.1 Calling up the customer care programmes > Press the care button for longer than 2 seconds. Select care programs select care program OK: P browse: -/+ > Use the care button to scroll to the desired customer care program. > Select the displayed program with the P button. Information on the function and application of customer care programmes are give as follows. 4.2.2 Warm up rinsing The pipes of the coffee machine are rinsed with hot water.
Care 4.2.3 WMF Connect & Clean milk system rinse The WMF Connect & Clean milk system rinse is unique worldwide; it allows you to easily maintain perfect beverages with milk and thus, make consistently enjoyable coffee. Tip: Before switching off, place the milk hose in the hot water spout and start the milk system rinsing by pushing the button. The machine subsequently switches off automatically. Hazard! Possible scalding due to hot rinsing water! If the milk hose is not fully screwed in it can work loose.
Care Milk system rinsing milk system rinsing OK: P browse: -/+ > Push the All-In-One spout to the upper most position. > Select the milk system rinsing with P button. The display notifies the individual activities that must be completed before the rinse. > Place a collecting vessel under the All-In-One spout. > Wipe the outside of the milk hose with a clean damp cloth. > Place the milk hose with the milk nozzle on the hot water spout (a). > Turn the milk hose in clockwise direction to the point of stop.
Care lower spout into beverage position 4.2.4 > Push the All-In-One spout slightly downwards. Machine-cleaning - Cleaning programme Hazard! Possible health hazard due to accidental ingestion of cleaning solution! Cleaning agents and descaling agents that are dispensed during the cleaning programme of your automatic coffee machine can affect your health. > Ensure that nobody drinks the cleaning solution that is dispensed.
Care empty drip tray > Follow the instructions in the display. refill water tank place 2L container under spouts insert tablet into coffee grounds slot > > > > 57 Place a suitable vessel (at least 2 litres capacity) under the All-In-One spout. Open the lid (2) on the ground coffee inlet. Place a cleaning tablet (2a) along with the yellow sponge in the ground coffee insert. Close the lid (2).
Care start: P Duration of the cleaning program: 7 minutes cleaning in progress time remain: 7 min. > Start with the P button. The cleaning program starts. A minute countdown indicates how long the cleaning will last. The machine-cleaning ends after 7 minutes. The display calls for a manual milk system cleaning. This display disappears after pressing the C button. After 250 brews or 14 days, the request for machine-cleaning appears on the display.
Care 4.2.5 Replace water filter This program appears when you use a water filter and the usage has been confirmed during the initial settings (chapter “2.5 Insert the WMF water filter” on page 10). However, depending on the water hardness and the water flow, at least after 3 months, a display requesting to change the water filter, appears. If you do not replace the water filter you must deactivate the use of the water filter under basic settings.
Care Rinsing water filter filter rinsing rinsing filter ... time remain: 4 min. > Start the filter rinsing with the care button. The filter rinsing program starts. A minute countdown indicates how long the rinsing will last. Filter rinse process ends after 4 minutes. While rinsing the filter, unusual noises are produced by the escaping air. This is normal. The noises end during the filter rinse. During further operation, everything sounds normal again. your selection pls 8:15 1.3.
Care 4.2.6 Descale coffee machine Hazard! Possible health hazard due to accidental ingestion of cleaning solution! Cleaning agent and descaling agent that are dispensed during the cleaning programme of your automatic coffee machine can affect your health. > After cleaning, rinse it with clear drinking water so that no cleaning solution remains in your automatic coffee machine. > Then empty the water tank of your automatic coffee machine.
Care > Press the release button (10a) at the back of the All-In-One-spout and pull the milk foamer (10b) off downwards. > Detach the milk hose (6) from the milk foamer (10b). > Remove the milk hose (6).
Care Descale automatic coffee machine machine descaling OK: P browse: -/+ Remove the water filter descaling ... time remain: 37 min. > Call the customer care programs (“4.2.1 Calling up the customer care programmes” on page 53). Browse with – or + to machine de-scaling. Confirm your selection with P button. Empty the drip tray. Remove the water tank from the automatic coffee machine. > Remove the filter cartridge and the filter adapter if a water filter is used.
Care empty water tank OK: P > Empty the water tank. > Rinse the water tank thoroughly with clear water. > Press P button. refill water tank OK: P > Fill the water tank with cold drinking water. > Place the lid on the water tank. > Slide the water tank gently into the automatic coffee machine. > Press the care button to continue the descaling. descaling ... time remain: 1 min. A minute countdown shows the remaining time of the descaling process.
Care 4.3 Manual cleaning 4.3.1 Clean the brewing unit The hygiene of your WMF 1000 S/ WMF 1000pro S is of particular importance to us. Hence, the brewing unit is detachable and the interior of the machine is easily accessible for cleaning. Hazard! Possible burn injuries while cleaning! The brewing unit of our automatic coffee machine is very hot while under operation and can cause burns. > Clean the brewing unit of your coffee machine on a regular basis.
Care If it is difficult to remove the brewer, the O-Rings must be lubricated. > Open the lid of the brewer (3). > Release the brewing unit (3a). > Pull the brewing unit (3b) upwards out of the brew chute. Use both the gripping lugs for pulling it out (3a). (“4.4.
Care > Turn the thread (3d) on the brewing unit head (3e) with the multitool in the anticlockwise direction. The scraper (3g) folds out forward and the brewing filter is now visible. > Clean the brewing unit (3e) under running water. > Clean the brewing sieve (3h and 3i) under running water. Caution! Possible damage to the brewing unit! The brewing unit of your automatic coffee machine can be damaged due to cleaning agent or by cleaning it in a dishwasher. > Use only water for cleaning the brewing unit.
Care > Pull out the water tank (7) and the coffee grounds container (11). > Remove the residues of ground coffee in both the openings (7a, 11a), for example, with a vacuum cleaner. > Turn the thread on the brewing unit head with the Multitool in a clockwise direction until the black scraper folds in again. > Insert the dried brewing unit till the lock clicks into place. > Close the lid of the brewer.
Care 4.3.2 General cleaning Caution! Possible damage to the water tank, the drip tray or the coffee grounds container! Due to the thermal effect in the dishwasher, the water tank, drip tray and coffee grounds container can be deformed. > Therefore, never clean the water tank, the drip tray and the coffee grounds container in the dishwasher. > Clean the housing only with mild cleaning agents. Grounds container and water tank cleaning > Empty the coffee grounds container and rinse it with water.
Care Clean the housing and control panel > Switch the coffee machine off with the off/c button (push for at least 2 seconds). > Remove the mains plug. > Clean the housing with a damp cloth. 4.3.3 Clean the milk system In domestic use we recommend cleaning the milk system once a week. > Remove the water tank from the machine. > Remove the milk hose from the milk container or release it from the milk lance. > Remove the milk hose from the guide.
Care > Detach the milk hose (6) from the milk foamer (10b). > Detach the milk nozzle (6a). > Detach the upper and lower part (10e) of the milk foamer from one another by pressing the part of the milk foamer with the spout downwards on a solid surface. > Detach the milk hose connection (10f) from the milk hose (6) and from the milk foamer > Unscrew the air inlet tube (10c) from the milk foamer and unscrew the black cap (10d) from the air inlet tube.
Care Using milk system cleaner > Fill the dispensing chamber (a) of the WMF milk system cleaner, by holding the closed bottle upright and pressing it. The bottle must be definitely held closed. Hazard! Hazard of eye injury! In case of eye contract, the WMF milk system cleaner can lead to serious eye injuries. > Ensure that the WMF Milk system cleaner never comes in contact with the eyes of humans or animals. a b Reassembling the parts > > > > > > Open the lid of WMF Milk system cleaner.
Care 4.3.4 Clean the steam nozzle Cleaning the steam nozzle is only required in the event of a fault.
Care b > Press the release button (10a) at the back of the All-In-One-spout and pull the milk foamer (10b) off downwards. > Carefully clean the steam nozzle (10e) in the All-In-One spout with one of the small cleaning brushes provided (b).
Care 4.4 Lubricating O-rings > Use only WMF “Grease for sealing rings” from the accessories. The grease/lubricant is suitable for the material and safe for food technology. 4.4.1 Lubricating O-Ring of the Water tank If it is difficult to remove the water tank and difficult to insert it, you must mildly lubricate the O-Ring on the water spout with the WMF “Gasket grease”. > Pull out the water tank (7). > Lubricate the O-Ring (7a) on the water spout with the WMF “Gasket grease”.
Care 4.4.2 Lubricating O-Ring of the Water tank If it is difficult to remove the brewing unit and difficult to insert it, you must mildly lubricate the O-Ring with the WMF “Gasket grease”. > > > > Open the lid of the brewing unit (3). Release the lock (3a) and lift the brewing unit from the brewing chute (3b). Mildly lubricate the O-Rings (3c) in the brewing chute with the WMF “Grease for gasket rings”. Make sure that no grease gets into the holes.
Display messages 5 Display messages Messages for operation and troubleshooting are displayed on your coffee machine. Thus, you always know how to proceed. 5.1 Emptying coffee grounds container Operating messages empty grounds cont. beverage sel. locked grounds cont.missing Empty drip tray 77 empty drip tray The coffee grounds container is full > Remove the coffee grounds container. > Empty the coffee grounds container and rinse it with water. > Wipe the coffee grounds container dry.
Display messages Refilling water tank beverage sel. locked refill water tank beverage sel. locked water cont. missing Fill the bean hopper Fill in the ground coffee refill beans confirm beverage insert coff. grounds select beverage The water tank is nearly empty. The water tank is never emptied completely so that no air enters the coffee system. > Remove the water tank from the automatic coffee machine. > Completely empty the water tank. > Fill the water tank with cold tap water.
Display messages your selection pls replace water filter Close the lid of the water tank tank lid missing? The lid is not placed or not correctly placed. > Place the lid on the water tank. Without the lid, the machine is not ready for operation. beverage sel. locked lid open The brewer lid of the automatic coffee machine is open. > Close the lid of the brewer. Close brewer lid Grinding too fine? Brewer is clogged? grinding too fi ne? brewer clogged? 79 The water filter must be changed.
Display messages 5.2 Messages for troubleshooting Brewer place brewer brewer pos. switch Flow clear fl ow stopped The brewing unit is not inserted. > Insert the brewing unit. The brewing unit is not inserted. > Check if the brewing unit is inserted correctly. The brewing unit is inserted only with difficulty or not at all inserted: > Remove the brewer. > Open the brewing chamber with the multitool. > Apply a thin layer of grease from the accessories to the red gaskets (chapter “4.4.
Display messages clear fl ow stopped (Water tank is full) clear fl ow stopped (Water tank is full) 81 Air in the system? Possibly associated with loud pump noise? > Check whether the water tank is completely pushed in. > Bleed the automatic coffee machine by dispensing hot water until a constant stream of water comes out. Is the water filter or sieve clogged? > Change the water filter (chapter “4.2.5 Replace water filter” on page 59). > Clean the sieve.
Display messages clear fl ow stopped (water tank is full) timeout steam level cleaning halted clear fl ow stopped Grinding too fine? > Set the degree of grinding to be coarser by one fourth rotation (chapter “3.6.3 Grinding grade setting: Perfect Extraction System” on page 40). > Suck out the grinding dust. Air in the system? Possibly associated with loud pump noise? > Check whether the water tank is completely pushed in. > Remove the milk hose from the milk container and press the milk foam button.
Display messages EEPROM Error > Switch the coffee machine off with the off/c button (push for at least 2 seconds). > Switch the coffee machine on with the off/c button. > If switching on does work, pull out the mains plug and re-insert it. On recurrence, the fault must be rectified by the WMF Service-Center. Motor driver motor driver error > Switch the coffee machine off with the off/c button (push for at least 2 seconds). > Switch the coffee machine on with the off/c button.
Display messages Grinder Temperature sensor grinder blocked The grinder is blocked by a foreign body. > Switch off the machine and pull out the mains cable. > Clean the bean hopper. > Insert the multitool (1) in the 2 holes (1a, 1b) in the grinder. > Turn the grinder (1) in a clockwise direction to remove foreign bodies. > Switch on the machine. > Start the grinder by pressing the beverage button. > If the grinder is free again: Reset the grinding grade. Grinding too fine.
Display messages 5.3 Problems without error display Problem No milk foam - / milk output, although there is milk in the container No milk foam, only hot milk Milk or milk foam too cold Rectification measure Milk hose kinked or squashed? > Re-fit the milk hose again. > Clean the All-In-One spout (chapter “4.3.3 Clean the milk system” on page 70). > Make sure that the milk lance is in the open position. > Carry out milk system rinse. Does the problem persist? > Clean the milk system (chapter “4.3.
Display messages Problem It is difficult to insert the water tank Rectification measure > Apply WMF grease from the accessories to the O-Ring on the water spout supports (chapter “4.4.1 Lubricating O-Ring of the Water tank” on page 75). It is difficult to remove the > Apply WMF grease from the accessories to the O-Ring on the water spout brewing unit and reinsert it. supports (chapter “4.4.2 Lubricating O-Ring of the Water tank” on page 76).
Display messages Problem 87 Rectification measure The brewing unit cannot be removed or reinserted > Adjust the brewing unit with the multitool as you are inserting it until you can insert the brewing unit. > Remove the residue of coffee grounds inside the brewer. There is a noticeable large amount of coarse ground coffee inside the brewer > Set the grinding grade finer by one rotation (chapter “3.6.3 Grinding grade setting: Perfect Extraction System” on page 40).
Technical data 6 Technical data WMF 1000 S Power rating Mains power connection On site circuit protection Coffee bean hopper Variable brewing chamber Capacity of water tank (without filter) Coffee grounds container Height adjustable All-In-One spout with milk nozzle High-performance pump Independent heating systems External dimensions Empty weight Weight of the brewer Cable length Continuous sound pressure level (Lpa) Machine type Manufacturer WMF 1000pro S 1,7 - 2,3 kW 1/N/PE ~ 50/60 Hz; 220 - 240 V ma
Index 7 Index A Adjusting the milk quantity ....................39 Adjusting the water volume ....................38 All-In-One spout ............. 11, 62, 70, 71, 74 Allow display of date/time .......................48 B Beverage settings ........................................37 Brewing temperature setting ...........................................46, 47, 53 C Café Crème preparing ...................................................26 Cancelling beverage preparation ...........
Index M Q Machine cleaning ........................................56 Manual cleaning ..........................................65 Bean hopper ..............................................69 Cleaning the milk nozzle ......................73 Coffee grounds container ...................69, 70, 71, 72 Drip tray and drip tray grid ..................69 Housing and control panel ................... 70 Milk lance ......................................................24 Motor driver error ......................
Transport and Disposal 8 Transport and Disposal > Retain the original packing as protection during transportation. > Empty the water tank, drip tray, grounds box and the bean hopper before moving. > Always dispatch or transport the machine in the original box with the expanded polystyrene shells. Disposal options for the device at the end of its service can be found out from your local municipal authority.
Legal details 10 Legal details © 2008-2011 WMF Corporation All rights, especially the right of reproduction, publication and translation, are reserved. No part of this manual may be reproduced in any form or processed, duplicated or distributed electronically without written consent. Subject to technical modifications. Design and production / typesetting and layout: reinisch AG, Albert-Nestler-Str. 24-26, 76131 Karlsruhe, Germany. Translated from the German original edition Printed in Germany.
WMF 1000 S Type 03 0500 WMF 1000 pro S Type 03 0510 User manual EN 03/2011
