Data Sheet
Table Of Contents
- UM-1
- Rev. 0.2
- UM-1
- RTLS and Communication module
- Description
- Key Features
- UWB compliant, on channels 3/5.
- Embedded PCB UWB antenna.
- ETSI, FCC, ISED Certified
- FCC ID: 2ARZVUM-1, IC:27701-UM1
- Supply voltage: 2.8 V to 3.6 V
- Size: 19.1 mm x 26.2 mm x 2.6 mm
- Operating temperature: -40 C to 85 C
- Applications
- D7A over UWB communication
- WizziLab product line at
- Table of Contents
- List of tables
- 1 Overview
- 1.1 UWB Transceiver DW1000
- 1.2 Bluetooth® Microprocessor Nordic nRF52832
- 1.3 Power Supply and Power management
- 1.4 Three Axis Motion Detector
- The LIS2DH12 is guaranteed to operate over an extended temperature range from -40 C to +85 C.
- 1.5 Software on board
- 2 Pin Connections
- 2.1 Pin Descriptions
- Table 1. Pin Description
- Table 2. I2C slave devices address I2C
- 3 Electrical specification
- 3.1 Nominal operating conditions
- Table 3. Recommended operating conditions
- 4 Wireless Specification
- Table 5. UWB transceiver operating conditions
- 4.2 BLE
- Table 6. BLE transceiver operating conditions
- 5 Functionality
- 5.2 Two-way ranging
- 5.4 BLE beaconing and sniffing
- 5.5 Tap-to-connect
- 6 How to use
- 6.2 Function API
- 7 FCC Caution
- 7.2 Radiation Exposure
- 8 ISEDC Warning
- Le présent appareil est conforme Après examen de ce matériel aux conformité ou aux limites
- D03 OEM
- UM-1
- Manual v01
- 2.2 List of applicable FCC rules
- CFR 47 FCC PART 15 SUBPART C&F has been investigated. It is applicable to the modular.
- 2.3 Specific operational use conditions
- 2.4 Limited module procedures
- Not applicable
- 2.5 Trace Antenna designs
- We supply the internal PCB antenna with UWB and Ceramic Antenna with BLE.
- 2.6 RF exposure considerations
- To maintain compliance with FCC's RF Exposure guidelines.
- 2.7 Antennas
- This radio transmitter FCC ID: 2ARZVUM-1 has been approved by Federal Communications Commission to operate
- Ceramic Antenna
- 2.8 Label and compliance information
- The final end product must be labeled in a visible area with the following" Contains FCC ID: 2ARZVUM-1"
- 2.9 Information on test modes and additional testing requirements
- 2.10 Additional testing, Part 15 Subpart B disclaimer
- 9 Revision history
- Table 7. Document revision history
- 10References
Pin Connections
UM-1
I2C_SDA
14
DIO
Master I2C Data Line.
P0.29
I2C_SCL
15
DO
Master I2C Clock Line
P0.28
GPIO_23
16
DIO
General purpose I/O pin.
P0.23
GPIO_13
17
DIO
General purpose I/O pin.
P0.13
UART_RX
18
DO
UART_RX
P0.11
READY
19
DO
Generated interrupt from the device.
P0.26
UART_TX
20
DIO
UART_TX, This is also the ADC function of the nRF52
P0.05
GPIO_1
21
DIO
General purpose I/O pin.
GPIO1
GPIO_0
22
DIO
General purpose I/O pin.
GPIO0
GPIO_15
23
DIO General purpose I/O pin.
P0.15
GPIO_8
25
DIO
General purpose I/O pin.
P0.08
SPIS_MISO
26
DI
SPI data output
P0.07
SPIS_MOSI
27
DO
SPI data input
P0.06
SPIS_CLK
28
DI
SPI clock
P0.04
SPIS_CSn
29
DI
SPI chip select
P0.03
GPIO_3
30
DO
General purpose I/O pin.
GPIO3
GPIO_2
31
DO
General purpose I/O pin.
GPIO2
BT_WAKE_UP
32
DIO
General purpose I/O pin.
P0.02
RESETn
33
DI
Reset pin. Active Low Input.
P0.21
VCC
12 P
External supply for the module. 2.8V - 3.6V
GND
1
G
Common ground
11
24
34
Table 2. I2C slave devices address I2C
I2C slave device
Address
LIS2DH12
0x19
WIZZILAB Technical datasheet 6/18