Data Sheet
Table Of Contents
- UM-1
- Rev. 0.2
- UM-1
- RTLS and Communication module
- Description
- Key Features
- UWB compliant, on channels 3/5.
- Embedded PCB UWB antenna.
- ETSI, FCC, ISED Certified
- FCC ID: 2ARZVUM-1, IC:27701-UM1
- Supply voltage: 2.8 V to 3.6 V
- Size: 19.1 mm x 26.2 mm x 2.6 mm
- Operating temperature: -40 C to 85 C
- Applications
- D7A over UWB communication
- WizziLab product line at
- Table of Contents
- List of tables
- 1 Overview
- 1.1 UWB Transceiver DW1000
- 1.2 Bluetooth® Microprocessor Nordic nRF52832
- 1.3 Power Supply and Power management
- 1.4 Three Axis Motion Detector
- The LIS2DH12 is guaranteed to operate over an extended temperature range from -40 C to +85 C.
- 1.5 Software on board
- 2 Pin Connections
- 2.1 Pin Descriptions
- Table 1. Pin Description
- Table 2. I2C slave devices address I2C
- 3 Electrical specification
- 3.1 Nominal operating conditions
- Table 3. Recommended operating conditions
- 4 Wireless Specification
- Table 5. UWB transceiver operating conditions
- 4.2 BLE
- Table 6. BLE transceiver operating conditions
- 5 Functionality
- 5.2 Two-way ranging
- 5.4 BLE beaconing and sniffing
- 5.5 Tap-to-connect
- 6 How to use
- 6.2 Function API
- 7 FCC Caution
- 7.2 Radiation Exposure
- 8 ISEDC Warning
- Le présent appareil est conforme Après examen de ce matériel aux conformité ou aux limites
- D03 OEM
- UM-1
- Manual v01
- 2.2 List of applicable FCC rules
- CFR 47 FCC PART 15 SUBPART C&F has been investigated. It is applicable to the modular.
- 2.3 Specific operational use conditions
- 2.4 Limited module procedures
- Not applicable
- 2.5 Trace Antenna designs
- We supply the internal PCB antenna with UWB and Ceramic Antenna with BLE.
- 2.6 RF exposure considerations
- To maintain compliance with FCC's RF Exposure guidelines.
- 2.7 Antennas
- This radio transmitter FCC ID: 2ARZVUM-1 has been approved by Federal Communications Commission to operate
- Ceramic Antenna
- 2.8 Label and compliance information
- The final end product must be labeled in a visible area with the following" Contains FCC ID: 2ARZVUM-1"
- 2.9 Information on test modes and additional testing requirements
- 2.10 Additional testing, Part 15 Subpart B disclaimer
- 9 Revision history
- Table 7. Document revision history
- 10References
2.6 RF exposure considerations
To maintain compliance with FCC's RF Exposure guidelines.
2.7 Antennas
This radio transmitter FCC ID: 2ARZVUM-1 has been approved by Federal Communications Commission to operate
with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a
gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Ceramic Antenna
-4.3/0.8
/PCB Antenna
2.8 Label and compliance information
The final end product must be labeled in a visible area with the following" Contains FCC ID: 2ARZVUM-1"
2.9 Information on test modes and additional testing requirements
Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when
the module is installed in the host.
2.10 Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module installed
with all other applicable requirements for the system such as Part 15 B
The manufacturers, or their authorized sales agents, must inform purchasers and users of
their systems of the requirement to undertake detailed coordination of operational areas with
the FCC prior to the equipment being operated.
Users of authorized, coordinated UWB systems may transfer them to other qualified users
and to different locations upon coordination of change of ownership or location to the FCC
and coordination with existing authorized operations.
WIZZILAB Technical datasheet 16/18