WT-1011RC IP65 G GS SM MR Re em mo otte eC Co on nttrro olllle err A An nd d A em m Alla arrm mS Sy ysstte User Manual & Setting Instructions W R R R W T U A C O P O A T O N S D N B H D WIIIT TU UR RA AC CO OR RP PO OR RA AT TIIIO ON NS SD DN NB BH HD D
WT-1011RC IP65 GSM Remote Controller And Alarm System PACKAGE CONTENTS 1) 2) 3) 4) 1 1 1 1 pc pc pc pc IP65 Enclosure WT-1011RC Main Board with GSM Module mounted Battery Backup GSM Antenna CONTENTS 1. Introduction………………………………………………………………………………………………………………3 2. Features………………………………………………………………………………………………………………………3 3. Characteristic……………………………………………………………………………………………………………3 4. Installation Instructions………………………………………………………………………………………………6 5.
WT-1011RC IP65 GSM Remote Controller And Alarm System 1. INTRODUCTION WITURA WT-1011RC GSM Remote Controller and Alarm System allow you to use your mobile phone to monitor and control your business from any location. Its alarm facilities provide a flexible way to distribute critical alarm information to any number of mobile phone users. WT-1011RC provides detailed alarm messages, secure alarm acceptance, full alarm reporting and even remote process control.
WT-1011RC IP65 GSM Remote Controller And Alarm System 3.1 Standalone Operation Housed in the weather and desk proof IP65 enclosure complete with internal industrial modem, monitoring controller and flexible operating firmware. It is very easy to setup, install and use. 3.2 2 Digital Inputs Most equipment today does provide some form of alerting signal to interface to monitoring devices from reporting of various malfunction or abnormalities.
WT-1011RC IP65 GSM Remote Controller And Alarm System Relay 1 can turned on for a preset time by calling its number and Relay 2 can be activated by text messages from mobile phone. Creating action messages are done with the same ease as that of input monitoring. 3.4 Querying Inputs And Outputs Status Authorized groups can also query the status of an input or output. This is very useful feature to determine the present status of an input or output.
WT-1011RC IP65 GSM Remote Controller And Alarm System 3.9 Reliable Performance Besides running the necessary program to perform all the required functions, WT1011RC has diagnostic routines running alongside. Being a monitoring device, WT1011RC must have a very high operating reliability and stability. Every section of WT1011RC is monitoring each other. Should the modem fail to perform its required role, the controller will interrogate and restart the modem. 3.
WT-1011RC IP65 GSM Remote Controller And Alarm System Installation: Power Switch Insert SIM card here Install Antenna here Connect to Battery Back-up Input 15VDC Power here Installing the SIM Card Note: Installing the SIM Card. Please be sure the initial 4 digit PIN code of SIM card is disabled. This can be done by placing it in an unlocked Mobile phone and first checking if the SIM requested any PIN code. If this is the case the PIN code can be disabled using the security settings on the phone.
WT-1011RC IP65 GSM Remote Controller And Alarm System Connection Details: If you are unsure how to connect the device you wish to control please refer to a qualified person.
WT-1011RC IP65 GSM Remote Controller And Alarm System Example of Input & Output Connections HEATER LIGHT +5VDC 110VAC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 + - + - + IN2 COM IN1 COM NO C NC NO C NC 12VDC Audible Alarm Output 15VDC Power Input +5VDC Output INPUT 2 INPUT 1 OUTPUT RELAY 2 5. 110VAC OUTPUT RELAY 1 WT-1011RC PROGRAMMING INSTRUCTIONS (via SMS Only) You can program the WT-1011RC via SMS commands using your phone.
WT-1011RC IP65 GSM Remote Controller And Alarm System Please note that it is possible to program up to a maximum of 16 digits for a phone number. Example: To program phone number 1111222233 as administrator into list number 1, you would send the following SMS command to the unit. *TEL1#1111222233 After sending the above command, the WT-1011RC will reply a message back to you that the administrator number has been added. Example of Returned Message: #TEL1=1111222233 5.
WT-1011RC IP65 GSM Remote Controller And Alarm System Text Command: *BOOK#nnXXXXXXXX nn stands for the position number 00 - 99 XXXXXXXX stands for last 8-digits of a phone number Example: To program phone number 1234567890 as Guest into the list, you would send the following SMS command to the unit. *BOOK#0034567890 Example of Returned Message: #WHL00-OK 5.4 OUTPUT Settings The WT-1011RC has 2 outputs that are connected to an on-board relay. Each output relay can be operated independently.
WT-1011RC IP65 GSM Remote Controller And Alarm System Example of Returned Message: #GOT1=00900 5.4.2 Switch On the Output Relay 2 For a Specific Time (By SMS) To activate output relay 2, you can send a text command via SMS specifying the number of seconds the output should stay on to the unit. It is possible to set up to maximum of 65,535 seconds.
WT-1011RC IP65 GSM Remote Controller And Alarm System *RETR#22222000 Example of Returned Message: #RETR=22222000 5.4.4 Follow function for Output Relays This function allows the second relay to latch at a specific time (GOTX) later after the first relay has latched and when the first relay has switched off the second relay will switch off after a specific time (GOTY). Text Command to Enable this Function: *FTRY#2 Text Command to Enable the normal Function (5.3.
WT-1011RC IP65 GSM Remote Controller And Alarm System 5.4.5 Setting the Operating Time for Output Relay 2 The output relay 2 can be programmed to operate at a programmable time. To program this function, you can send the following commands by SMS message to the unit. Text Command to Enable this Function: *FTRY#3 Note: When this function enabled, functions related to activation of output relay 2 will be disabled and activation of output relay 2 via SMS will be rejected.
WT-1011RC IP65 GSM Remote Controller And Alarm System 5.5 INPUT SETTINGS One of the most important functions of WT-1011RC is to receive alarms. In order to use this function, you must turn on the function of the inputs and tell the WT-1011RC which are the recipient numbers and who should receive the alert message for the particular input. 5.5.1 Turn On the Function of Inputs To turn on the function of input, you can send the following commands by SMS message to the unit.
WT-1011RC IP65 GSM Remote Controller And Alarm System N stands for input number 1 - 2 X stands for position for 1 - 8 administrators with function value: 0 (OFF), 1 – 9 (number of text alerts) Example 1: Any alarm coming from Input 1 will generate 2 SMS to administrators 1, 2, 3 and 1 SMS to the rest; you would send the following SMS message to the unit.
WT-1011RC IP65 GSM Remote Controller And Alarm System 5.5.4 Editing the Input Alert Message For (When Input returned to Normal) The Input Alert Message can be edited and programmed up to 40 characters long. You can change the displayed text by sending the following commands by SMS message to the unit. Note: Only support normal abc/ABC English text, no special characters.
WT-1011RC IP65 GSM Remote Controller And Alarm System 5.5.6 Setting the Feature of Input All inputs can be programmed to behave differently, it can count the input active high pulses, generate an alarm message or activate relay. To program the input, you can send the following commands by SMS message to the unit.
WT-1011RC IP65 GSM Remote Controller And Alarm System Function 3: Function as pulse counter Activates the output relay 2 to stay ON Sends a programmable input alert message (*STR2#) once input triggered Audible alarm will sound if the alarms function is turned on (*ALM2#1) Function 4: Function as pulse counter Activates the output relay 2 for 2 seconds Sends a programmable input alert message (*STR2#) once input triggered Audible alarm will sound if the alarms function is tur
WT-1011RC IP65 GSM Remote Controller And Alarm System *CTC1#1 Example of Returned Message: #CTC1=<1> Note: Only Input 1 may apply function F1 where only 2 selectable functions available. Only Input 2 may apply function F2 where 8 selectable functions are available. 5.6 ALARM SETTINGS 5.6.1 Turning the Audible Siren Functions On/Off When Inputs Triggered The system has the function to sound the connected audible siren when input triggered. This output is available on PIN1 and PIN2 of the connector block.
WT-1011RC IP65 GSM Remote Controller And Alarm System 5.6.3 Power Down Alarm The system has the function to send a text alert in the event the main power is lost and the system is relying on battery back up. It is also possible to activate and deactivate this function by sending the unit an SMS Message.
WT-1011RC IP65 GSM Remote Controller And Alarm System 5.6.5 Anti-Theft Feature The system has an anti-theft function that can used to detect the person who hijacks the WT-1011RC device. It allows the owner to identify the hijacker’s SIM Card number by sending a warning message to the programmed owner’s number when the SIM card has been switched. To activate and also deactivate this function, you can send the following SMS command to the unit.
WT-1011RC IP65 GSM Remote Controller And Alarm System 5.7 MISCELLANEOUS SETTINGS 5.7.1 Inquire All Programmed Administrator Numbers To check all the administrator number in the list, simply send the following SMS command. Text Command: *ADM?# 5.7.2 Inquire the Status of Inputs To check input status, you can send the following SMS command.
WT-1011RC IP65 GSM Remote Controller And Alarm System Send the following SMS Command: *COA?# 5.7.5 Reading the Total Increment Counter Value To read the total increment counter value, you can send the following SMS message to the unit. Text Command: *COU?# Example of Returned Message: *INC1=00000.0#INC2=00000.
WT-1011RC IP65 GSM Remote Controller And Alarm System 5.7.7 Reset the Total Increment Counter Value To reset the total counter value, you can send the following SMS message to the unit. Text Command: *CLA[N]# N stands for Input number 1 – 2 Example: When *CLA1# is sent, means the total increment counter value will be reset 5.7.
WT-1011RC IP65 GSM Remote Controller And Alarm System 5.7.9 Checking Signal Strength To check the signal strength (0-31), you would send the following SMS command to the unit. Text Command: *CSQ?# 5.7.10 Checking the Serial/IMEI Number of WT-1011RC Device To check the serial/IMEI number, you would send the following SMS command to the unit. Text Command: *SERIE?# 5.7.
WT-1011RC IP65 GSM Remote Controller And Alarm System Example of last 20 events received by SMS: *LACC=C011102S032012C302050C352315C252359C870015C140056C260615C270815S30 0925S021015C301130C351520C251615S161616C151620C031725C021730C011800C0218 02 Note: The last 20 events report will be sent only when GPRS function is disabled and the output relay is on normal function (*FTRY#1). Make sure the time clock is programmed otherwise the time will not shown correctly. 5.7.
WT-1011RC IP65 GSM Remote Controller And Alarm System 5.8 Connection of RS-232 Cable for Programming The WT-1011RC can be program with the provided programmer software. To do so the WT-1011RC unit must be turned on and connected to the computer’s COM port with the provided RS-232 cable as shown below. For software programming details please refer to the WT-1011RC Programmer Guide. WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: technical@witura.
WT-1011RC IP65 GSM Remote Controller And Alarm System 6.