WT-248 G GS SM M8 8P Po orrttss A An na allo og gG Ga atte ew wa ay y User Manual W R R R W T U A C O P O A T O N S D N B H D WIIIT TU UR RA AC CO OR RP PO OR RA AT TIIIO ON NS SD DN NB BH HD D
WT-248 GSM 8 Ports Analog Gateway GSM Gateway Introduction Welcome to use our GSM Analog Gateway (also named as Analog Channel Bank/ SIM Bank) to enter a novel communication world, which absorbs high-tech and delicate design out of your imagine. The GSM Analog Gateway enables you to quickly achieve the GSM cell telephone communication just via simple operations of wired telephone. This briefing helps you understand the functions of GSM Gateway step by step.
WT-248 GSM 8 Ports Analog Gateway Rear View with Connection to Telephone & PC View of 4 SIM Card Holder at the board of 1 Port ATTENTION !!! • • • • • • • Please read the following specific rules - Against the rules will cause danger or violate the law Echo off - Before using this equipment, please make sure your position has no echo off function for wireless radio frequency signal Interference - The similar to all mobile telephones, it is subject to the interference, which affects functions of the tel
WT-248 GSM 8 Ports Analog Gateway • • • • • Antenna - Only approval antenna can be used, do not link the antenna which do not match with the equipments. The unqualified antenna in use will damage the equipments. Antenna must keep vertical and off the telephone, the antenna cable cannot be bound with telephone line together. Do not touch antenna or approach antenna in range of 10m during calling.
WT-248 GSM 8 Ports Analog Gateway Configuration And Installation 1. The whole pack of the PRI Gateway includes: • • • • • Analog Channel Bank (Main Unit) High Gain Antenna Antenna Splitter 110 – 220V AC Power Line Telephone Cord 1 set 2 pcs 2 pcs 1 pcs 8 pcs 2. Installation Procedure The equipment provides digital GSM network communication, which required a valid SIM Card.
WT-248 GSM 8 Ports Analog Gateway 3. Instruction a) This PRI Gateway (Analog Channel Bank) application figure: WT-248 – USER MANUAL – Rev.1.5 – Technical Support: technical@witura.
WT-248 GSM 8 Ports Analog Gateway The installation connecting to charging device b) The front-panel indicator appearance illumination There are pick-up or hang-up handset indicator and strong or weak signal indicator for each route of the PRI Gateway (Analog Channel Bank) Pick up or hang up the handset: If pick up a route of the PRI Gateway (Analog Channel Bank), the pick up or hang up indicator keep bright. (Red LED).
WT-248 GSM 8 Ports Analog Gateway When the “strong or weak signal” indicator indicates there is enough receiving signal, pick up the telephone which connecting with the PRI Gateway (Analog Channel Bank), and you can hear the dialing tone immediately; If connecting the machine with the fee counter, it will show the telephone number you dial. After the other side picks up the phone handset, the charging machine starts working.
WT-248 GSM 8 Ports Analog Gateway TECHNOLOGY INDEX 1. Antenna interface level: 900/1800/1900Mhz, 850/900/1800/1900Mhz GSM GSM GSM GSM 850Mhz: 900Mhz: 1800Mhz: 1900Mhz: RX RX RX RX 869-894 925-960 1805-1880 1930-1960 TX TX TX TX 824-849 880-915 1710-1785 1850-1910 2. SIM Card: It support 3VG-SIM Card 3. Phone Interface: Supply main and assist double frequency interface (RJ-11 Phone Interface) Hanging Voltage: 45V Picking Off Voltage: 30mA/ 41mA Dialing Tone Frequency: 450Hz 4.
WT-248 GSM 8 Ports Analog Gateway EXCEPTION HANDLES 1. Network After opening the GSM PRI Gateway (Analog Channel Bank), the equipment needs about 10 seconds to search for the local network of GSM. When searching the most right-hand “signal strong or weak” indicator would flash once per second until searching completes, then the “strong or weak signal” indicator starts indicating to make a phone call. 2.
WT-248 GSM 8 Ports Analog Gateway • • • • • • • • • • • • • • • Worldwide flexible power supply Add prefixed code automatically Locking wireless terminal Locking SIM Card Locking service provider Locking districts Call billing prefixed Caller ID blocked (optional and need network supported) Voice volume adjustable Providing corporate business fixed to mobile/ mobile to fixed telephony Providing rural connectivity over GSM networks Providing quick basic telephony provisioning Providing GSM connectivity for
WT-248 GSM 8 Ports Analog Gateway b) • • • • *2*1XXX#: *2*2XXX#: *2*3XXX#: *2*4XXX#: Indicate Indicate Indicate Indicate Number Number Number Number of of of of times times times times using using using using SIM SIM SIM SIM Card Card Card Card No. No. No. No. 1. 2. 3. 4. XX=001-999 XX=001-999 XX=001-999 XX=001-999 Example: *2*1008# means the number of times using SIM Card No. 1 is 8 times *2*3125# means the number of times using SIM Card No.
WT-248 GSM 8 Ports Analog Gateway 4. Speed Dial Setting • *5X#: Indicate the delay time (seconds) for speed dial. X=1-8. Example: *52# means auto dial number after 2 seconds dialing destination no. *55# means auto dial number after 5 seconds dialing destination no. 5. Setting for Factory Default: **000# • • • • • Default Default Default Default Default Setting Setting Setting Setting Setting for for for for for SPK is 2 MIC is 2 SIM Card is using SIM Card No.
WT-248 GSM 8 Ports Analog Gateway Error Indicator: • E1: Indicate there is connection problem between the Modules and the PCB Board (If the display show E1 more than 5 seconds after the terminal switch on) • E2: Indicate Cannot Read SIM Card (E2 and SIM X will take turn to display) • E3: Indicate Can Read SIM Card but No Signal (E3 and SIM X will take turn to display) 2. 2 LED Light Indicator. 1 LED for “WORK”, 1 LED for “IN USE” • WORK: The LED will lighten up when switch on the terminal.