WT-1018C1 G GSSM M FFIIXXEED DW WIIR REELLEESSSS TTEER RM MIIN NA ALL User Manual W R C O R O R O N S D N W T U A P A T B H D OR NS DN NB WIIIT TU UR RA AC CO RP PO OR RA AT TIIIO ON SD BH HD D
WT-1018C1 USER MANUAL Sketch of the Fixed Wireless Terminal ANTENNA The antenna must be well connected before turn on the terminal POWER INDICATOR (RED) The indicator is illuminated when mains power is present NETWORK INDICATOR (GREEN) The indicator is illuminated when the terminal is connected to GSM Network Installation & Wiring TEL PORT 1 Connect to Telephone ANTENNA PORT Connect the provided antenna to the Terminal TEL PORT 2 Connect to PSTN Line ON/OFF SWITCH Turn On or Off the Terminal DATA
WT-1018C1 USER MANUAL Please check the following packing list: Name WT-1018C1 Main Unit Telephone line Power adapter 5m GSM terminal antenna User’s Manual Quantity 1 1 1 1 1 Unit set set set set set Contents 1. Main Features of WT-1018C1.………………………………………………………………………………....4 2. Caution……………………….………………………………………………………………………………………………4 3. Storage……………………………….…………………………………………………………………………………..…4 4. Installing SIM Card……………………………….…………………………………………………………………..5 5.
WT-1018C1 USER MANUAL 1. Main Features of WT-1018C1 Adopt advanced microprocessor controlling circuit, run steadily. Capability is ascendant Adopt high gains antenna. Signal is strong Be applicable for GSM900MHz/DCS1800MHz/PCS 1900MHz Call or called function can be set up flexibly The functions of locking terminal and locking SIM card can be set up conveniently. Function of displaying incoming calls. Provide accurate anti-polarity signal for billing equipment to charge. 2.
WT-1018C1 USER MANUAL Don’t knock terminal to avoid breaking the case. Don’t use chemic impregnant to clean terminal, but use dry soft cloth to make it clean. 4. Installing the SIM Card Proceed as follows: 1. Slide back the SIM door and lift it up 2. Slide the SIM card into the SIM door making sure that the clipped corner of the SIM card lines up with the clipped corner of the SIM holder 3. Close the SIM door 4.
WT-1018C1 USER MANUAL 4. Install the antenna and power supply well. The distance between telephone and terminal is 1.5m at least. 5. Connect one end of the power adapter to “Power port” and another end connects to 220v AC power. 6. Turn on the terminal. 7. When the terminal is ready to use, it will display as below Power Signal WT-1018 Draw your attentions: Because there are many types of ordinary telephone and their electric parameters are different.
WT-1018C1 USER MANUAL **12345678 DIAL SETTING… Continue press *8* to setup a PIN PIN: Enter a PIN code that match with the PIN code of the SIM card and confirm with # PIN: 1234 REPEAT INPUT PIN PIN: Enter the PIN code again and confirm with # WT-1018C1 – USER MANUAL – Rev 1.5 – Technical Support: Technical@witura.
WT-1018C1 USER MANUAL COMPARE INPUT PIN: OK Now the PIN code of the terminal has setup successfully. Quit the programming mode by simply hook-on the phone or press the “hand-free” Turn off the terminal and install the SIM card. Turn on the terminal again. This time the terminal will check and match the PIN code of the SIM card as shown below.
WT-1018C1 USER MANUAL Setup PIN code for Terminal with a PIN code enabled SIM card If the PIN code of the terminal hasn’t been setup, you can also program the PIN code by first installing the SIM card with PIN code enabled and turn on the terminal. When turned on, it will display as below LOADING:>>> WAITING… OK THE TERMINAL NEED INPUT PIN You can lift the handset or press the “hand-free” key.
WT-1018C1 USER MANUAL IN CHECK PIN… OK PIN OK SAVE OR NOT: Simply press 1# to save the PIN code into the terminal PIN OK SAVE OR NOT: OK The terminal will then proceed to standby mode. Warning! Now the terminal is locked and only recognizes the installed SIM card. PIN Code Incorrect Procedure If the entered PIN code is incorrect, it will display as the following… IN CHECK PIN… Error attempt ERROR: 1 PIN: Note: There are only 3 attempts for entering the wrong PIN code.
WT-1018C1 USER MANUAL You will have to check with the network operator for PUK to unlock the SIM card. 6. The Installation for connecting to register cost equipment If users demand register cost during calls, register cost equipment can be connected between terminal and ordinary telephone. Register cost equipment registers cost according to anti-polarity signal that is provided by terminal. 7.
WT-1018C1 USER MANUAL (the signal is used to register cost by register cost equipment). During a call, dial digital key or “*” or “#” to output DTMF. 7. If the calling party or called party hangs up, the terminal stops sending out anti-polarity signal. 8. If users dial barred numbers, telephone will give out the sound of three-time toot to ask the user to hang up. 8.
WT-1018C1 USER MANUAL 9.2 Programming Setting Instructions Steps: A. Enter Programming Mode Pick up the handset or press “hand-free” on the connected telephone, input **12345678#. If heard “du~” a short dialing tone, means the Password has entered correctly, and then it will continue to programming setting mode. User is able to do programming at this state. If there is no tone and error appears on the screen, means the Password entered is not correct. And it will not go into programming setting mode.
WT-1018C1 USER MANUAL **12345678 OK DIAL Password entered correctly SETTING… Programming Mode Step 2: Changing the Programming Access Password To change the 8 digits programming access password, you can press *0* to proceed. NEW PASSWORD: NEW PASSWORD: 87654321 Input new password and ended with # NEW PASSWORD: 87654321 OK Step 3: Setting the Delay Time of Sending the Destination Number To set the delay time of sending the destination number, you can press *5* to proceed.
WT-1018C1 USER MANUAL Example: To set the delay time for 3 seconds Simply input 03 and ended with # DTTRANSMIT: 03 OK Note: The delay time value range from 00 –59 seconds (Default: 20 seconds) Step 4: Setting the Function of switching the dialed number to GSM To switch the dialing number *, 0 or 00 to GSM, you can press *7* to proceed.
WT-1018C1 USER MANUAL Example: To set the delay time for 6 seconds Simply input 06 and ended with # IP DELAY TIME: 06 OK Note: The delay time value range from 00 – 59 seconds (Default: 20 seconds) Step 6: Adding/Deleting IP or Gateway Number Adding IP or Gateway Number The terminal can automatically add the IP or Gateway Number in front of the Destination Number when making a call. To setup IP number, you can press *1* to proceed.
WT-1018C1 USER MANUAL IP: Simply press # without input any number to delete DEL IP: OK Step 7: Setting the PIN Code for the WT-1018C1 Terminal (Optional) To setup a PIN code, you can press *8* to proceed. PIN: PIN: 1234 Example: To setup the PIN code as 1234 Simply press 1234# PIN: 1234 REPEAT INPUT PIN PIN: 1234 Enter PIN again and press # to confirm WT-1018C1 – USER MANUAL – Rev 1.5 – Technical Support: Technical@witura.
WT-1018C1 USER MANUAL COMPARE TWICE INPUT OK Note: Once PIN code is programmed, the terminal will only recognize the SIM Card with that PIN code. Step 8: Clear the PIN Code of the WT-1018C1 Terminal (Optional) To clear the PIN code of the WT-1018C1 Terminal, you can press *10* to proceed.
WT-1018C1 USER MANUAL Disable SIM PIN Protection To disable PIN protection of the SIM card, you can press *15* to proceed. PIN PROTECT OFF PIN: PIN PROTECT OFF PIN: 1234 To turn off SIM PIN protection, simply enter the default PIN 1234# IN CHECKING… OK Step 10: Allow or Bar Incoming Calls To allow or bar incoming calls, you can press *2* to proceed.
WT-1018C1 USER MANUAL To allow or bar National calls, you can press *3* to proceed. BAR ZERO ON&&OFF: BAR ZERO ON&&OFF: 1 To bar national calls simply press 1# To allow national calls simply press 0# BAR ZERO ON&&OFF: 1 OK Default Value: 0 Step 12: Allow or Bar International Calls To allow or bar National calls, you can press *4* to proceed.
WT-1018C1 USER MANUAL Miscellaneous Settings Inquire the Programmed PIN Code of the WT-1018 Terminal To check the programmed PIN code, you can press *9* to proceed. THE PIN NUMBER IS: 1234 The PIN code will be displayed on screen Press # to turn back Adjusting the Speaker and Microphone volume of the WT-1018 Terminal To adjust the speaker and microphone volume, you can press *12* to proceed.
WT-1018C1 USER MANUAL To confirm reset simply press 1# To cancel and turn back simply press 0# REST DATA ON&&OFF: 1 OK Checking the Hardware and Software Version of WT-1018C1 To check the hardware and software version of WT-1018C1, you can press *17* to proceed. HW: 1.0ver SW: 1.8 ver MW: 1.5ver The Hardware and Software Version will be displayed on screen Press # to turn back 10. Technical Specifications 1.
WT-1018C1 USER MANUAL 11. Troubleshooting Phenomena Signal indicator isn’t lit Trouble Failed in login onto GSM network Trouble Shooting 1. The signal is too weak Please move the terminal to the place where signal is stronger. 2. Check whether antenna is connected well. 3. SIM card is locked. Please contact the service provider. 1. Check whether antenna is connected well. 2. The signal is too weak Move the terminal or antenna to the place where signal is strong. 1.
WT-1018C1 USER MANUAL Warranty Witura Corporation Sdn Bhd guarantees all WT-1018 GSM Fixed Wireless Terminal against defective parts and workmanship. Witura Corporation Sdn Bhd shall, at its option, repair or replace the defective equipment upon the return of such equipment to any Witura branch.