Installation and Operating Instructions CAN WITTE Velbert GmbH + Co KG Höferstr. 3-15, D 42551 Velbert GERMANY Contents Revision Datum Bearbeiter 1.0 09.11.
1 General 1.1 Explanation of symbols 1.2 Limitation of liability 1.3 Service 2 Safety information 3 Product description / Technical data 4 5 6 3.1 Intended use 3.2 General Description 3.3 Technical data 3.4 Additional hardware Transport 4.1 Symbols on the packaging 4.2 Transport inspection 4.3 Packaging 4.4 Storage Interface 5.1 CAN Interface 5.2 Bluetooth 5.3 NFC interface 5.4 RF Sniffer Installation 6.1 Unpacking 6.2 Installation instructions KPC (Optional) 6.
7 Operation 8 Maintenance 8.1 Cleaning 8.2 Inspection 8.
1 General NOTICE These Instructions are an integral part of the flinkey CAN and must be kept in the immediate vicinity at a place accessible by personnel at all times. Personnel must have carefully read and understood these Instructions prior to beginning work. Prerequisite for safe work is the compliance with all safety information and instructions given in these Installation and Operating Instructions.
… indicates hazards resulting from hot surfaces. Failure to comply with the safety information may result in serious injury. … indicates hazards resulting from cold surfaces. Failure to comply with the safety information may result in serious injury. 1.2 Limitation of liability All data and information given in these Instructions were compiled in accordance with the applicable standards and regulations, the state of the art as well as our extensive knowledge and experience.
2 Safety information NOTICE Please take the time to read the general safety instructions. Follow all instructions. This will avoid fire, explosions, electric shocks or other hazards that may result in damage to property and/or severe or fatal injuries. Please read all safety information and instructions. The manufacturer is not liable for cases of material damage or personal injury caused by incorrect handling or non- compliance with the safety instructions. In such cases, the warranty will be voided.
WARNING Risk of injury! Without sufficient fixing the flinkey CAN can cause hazards for the vehicle driver or passengers in case of a full brake application (i.e. head injuries). Make sure that the CAN Box does not cause any risks to the drivers or passengers. Always make sure the flinkey CAN is positioned safely in the vehicle. WARNING Risk of injury! Do not use electrical equipment if you are lacking in concentration or awareness, or are under the influence of drugs, alcohol or medication.
3 Product description / Technical data 3.1 Intended use The WITTE Digital flinkey CAN is intended to be used as a smart actuator to access passenger vehicles, commercial vehicles and transporters. The task of the box is to lock or unlock a motor vehicle after receiving a corresponding command via CAN interface by cable from a partner device. WARNING The products may only be used according to the instructions as described in this manual.
Fig. 2:flinkey CAN bottom side (example) The box uses two camshaft-driven drag levers that can operate the key buttons for locking or unlocking the vehicle via central locking This makes it possible to implement different forms of key transfer, according to the functionality of the vehicle (steering wheel lock vs keyless start). The combination of the key receptacle (key bed) and the two towing levers must be adapted to the shape of the vehicle key.
In addition to the electromechanical infrastructure, an NFC and BLE gateway are also available, which can be used as a communication interface by the partner device. Furthermore, an RF sniffer is installed to detect the emitted radio signals of the activated vehicle key. Fig.
3.3 Technical data Product Design Trade mark Year of production Manufacturer flinkey CAN 8.0 flinkey 2022 WITTE-Velbert GmbH & Co. KG Höferstr. 3-5 D-42551 Velbert Total weight Dimensions App. 620 g 164 mm x 139 mm x 61 mm Operating temperature -40 °C .. +85 °C Rel. air humidity 50% at 60 °C Power supply Current rating 12 VDC neg Ground Connector TE-1418888-5 for more details s. chapter 5 Degree of protection Protection class IP30 III Radio technology BLE (Bluetooth Low energy) BLE 5.1 2.
Fig. 5:Keyfob with KPC (example) Fig. 6:Keyfob with KPC (example) NOTICE The KPC adapter can only be used for suitable keyfobs. Please contact WITTE digital to check if a KPC adapter is available for the keyfob. (s. chapter 1.
4 Transport 4.1 Symbols on the packaging Fragile Marks packages with fragile or sensitive contents. Handle package with care, do not drop or expose to shocks. Keep dry Keep package dry. 4.2 Transport inspection Check the consignment for completeness and transport damage immediately upon receipt. In case of visible transport damage (defective packaging i.e.) please proceed as follows: 1. Refuse delivery or accept delivery subject to reservation. 2.
4.4 Storage The packages must be stored under the conditions below: ➢ Do not store outdoors. ➢ Store dry and free from dust. ➢ Do not expose to aggressive media. ➢ Protect from solar radiation. ➢ Avoid mechanical shock and vibration. ➢ For storage conditions (temperature / air humidity) see chapter 3.
5 Interface 5.1 CAN Interface Main Connector pinout Pin 1 Ground (negative) Pin 2 Supply voltage (positive) Pin 3 CAN-L (CAN bus low pin) Pin 4 CAN_H (CAN Bus high pin) Pin 5 Reserved Pin 6 Reserved Note: Pin number marking clearly visible inside receptable- CAN bus Description Data rate Features Not galvanically isolated, referred to ground (pin1) Up to 5Mbit/s CAN FD, bus wake-up 5.
Antenna wire diameter Antenna coil length Maximum power to antenna/coil Ton (1 cycle) Toff (1 cycle) Duty cycle Events per 6 minute period (max) PCB trace 0.5 mm wide 35 μm thick 566 mm 0.34 W 180ms 700ms 20.45% (max). 120 5.
6 Installation WARNING Risk of injury! Read all safety information in the chapter Safety Information before installing the product. WARNING The flinkey CAN is pre-assembled by the manufacturer for a specific keyfob type. This settings couldn’t be adjusted after the box left the manufacturer’s factory. The box can’t be opened without destroying it.
2. Remove the manufacturer's battery from the keyfob. 3. Choose the correct KPC for the replacement. (please contact manufacturer) 4. Place the corresponding KPC in the batterie position: 5. Close the keyfob with the upper part and bend the cable in the direction as seen in the following figure: 6. Connect the plug to the socket in the keybed of the drawer of the box. Then place the keyfob in the keybed.
7. Then close carefully the drawer of the box. While closing, be careful not to damage any cables! For further installation, follow the next chapter. WARNING Risk of injury! There is a risk of crushing fingers while closing the drawer of the box.
6.3 Installation instructions flinkey CAN WARNING Risk of injury! Without sufficient fixing the flinkey CAN can cause hazards for the vehicle driver or passengers in case of a full brake application (i.e. head injuries). Make sure that the CAN Box does not cause any risks to the drivers or passengers. Always make sure the flinkey CAN is positioned safely in the vehicle.
2. Make sure the hook-and-loop strips are attached to each other. 3. Remove the liners from the hook strips. 4. Place the hook strips at an equal distance on the bottom of the flinkey CAN 5. 6. Place the flinkey CAN on the surface of the car where you want to affix the box (e.g. carpet, fleece or floor). Press well to make sure the strips stick to the surface. NOTICE In case of malfunctions or deviations please contact the manufacturer's service (see Chapter 1.
7 Operation WARNING Any use of the device exceeding the intended use and/or any other use is regarded as improper use and may lead to dangerous situations. WARNING Risk of injury! There is a risk of crushing fingers while closing the drawer. WARNING Risk of burn! Always protect the flinkey CAN from direct sunlight and never place the flinkey CAN in direct sun light.
8 Maintenance WARNING This product does not contain any user-serviceable parts. The flinkey CAN can’t be opened without destroying the enclosure. Configuration, servicing, and repairs must only be made by an authorized reseller or installer. WARNING Risk of injury! Without sufficient fixing the flinkey CAN can cause hazards for the vehicle driver or passengers in case of a full brake application (i.e. head injuries). Make sure that the CAN Box does not cause any risks to the drivers or passengers.
9 Disposal of the Product If no agreements have been made for return or disposal, have the product and its component recycled: ➢ Scrap metals. ➢ Recycle plastic elements. ➢ Sort and dispose of other component parts according to their material properties.
10 Declaration of Conformity Hereby, WITTE Automotive GmbH declares that the flinkey CAN is in compliance with the Directives 2014/30/EU and 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: www.witte.digital The flinkey CAN has an ECE Approval regard to Regulation No. 10 issued by the KBA (Approval N° E1*10R06*XXXX).
11 FCC This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
13 This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de licence.
Copyright © 2022 by WITTE Digital All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of the publisher. For permission requests, write to the publisher, addressed “Attention: Permissions Coordinator,” at the address below. WITTE Digital WITTE-Velbert GmbH & Co.
