MPR30-IEM User Manual High performance True diversity Receiver SN: ________________ Rev. 06 (ref. FW v1.
MPR30-IEM User Manual 1 Rev.
MPR30-IEM User Manual Rev. 06 BRIEF DESCRIPTION MPR30 is a compact true diversity receiver designed for professional in-ear monitoring applications. This receiver features a real TRUE DIVERSITY configuration along with a unique wideband tuning range up to 232 MHz. Audio processing can be Stereo MPX or mono based. The output audio stage is especially design to have maximum audio peak-dynamic of 200 mW. MPR30-IEM is designed to be: “easy & quick to use” thanks to o automatic setup functions (i.e.
MPR30-IEM User Manual Rev. 06 SAFETY INSTRUCTION Read this safety instruction and the manual first Follow all instructions and information. Do not lose this manual. Do not use this apparatus under the rain or near the water. Do not install the apparatus near heaters or in hot environments, do not use outside the operating temperature range. Do not open the apparatus, only qualified service technician are enabled to operate on it.
MPR30-IEM User Manual Rev. 06 BATTERIES MPR30-IEM works with standard camera battery: 2xIEC-LR6 1.5 size-AA alkaline or NiMh rechargeable KLIC 8000 (lithium-ion, rechargeable) Ricoh DB-50 (lithium-ion, rechargeable) DR9708 Duracell (lithium-ion, rechargeable) Battery status can be checked on OLED display or looking the status of LED indicator ON. Lithium-ion battery can be charged through A. dedicated charger B.
MPR30-IEM User Manual Rev. 06 PRODUCT OVERVIEW Upper Panel ON LED indicator Headphone Output On/Off/Volume control SMA connector Antenna B SMA connector Antenna A SMA antenna Connector A and B MPR30-IEM is supplied with two couple of antennas. According to the working band, different antenna models can be supply. All the models have Antenna Code label black cap and a black label with code in white colour.
MPR30-IEM User Manual Rev. 06 Front panel MPR30-IEM allows an easy and quick configuration using buttons, RGB LED’s and an OLED display. ON Led Indicator SCAN/DOWN Button MENU/SELECT Button RF Led Indicator SYNC/UP MENU/EXIT Button Infrared Interface (IR) OLED Display The receiver has a high contrast display. Pushing one of the 4 buttons while the receiver is active (but the display is off), turn on automatically the display.
MPR30-IEM User Manual Rev. 06 charging status battery status Tuning phase power up ON & RF Led Indicators (Firmware rel. v0.
MPR30-IEM User Manual Rev.
MPR30-IEM User Manual DISPLAY MENU Audio Settings Out mode Stereo/Mono/Mix Balance Vol. boost L|R Low (-12÷+12) Hi (-12÷+12) -12÷+12dB Output load 32Ω/16Ω Pwr limit OFF/100mW/50mW/30mW Equalizer Gr-Ch Frequency Edit RX Squelch Scan Rev. 06 GR (0÷39) CH (0÷59) N: 470.000÷700.000 M: 566.000÷798.000 *Only using lithium battery OFF*-0/3/6/9/12/15/18/21/24//28/32/36/40/46 dBµV Channel GR 00 - 39 Groups more groups (max 10) Scan now freq. Min/ freq.
MPR30-IEM User Manual Rev. 06 From Status Display push SEL and EXIT together to enter on the Main menu Use UP/DOWN to navigate on all available menus Push SEL to select a menu item Use UP/DOWN to move on the different parameters of the menu Push SEL to modify the parameter menu Use UP/DOWN to change the parameter value Keep push SEL to save changing Push EXIT to return on the Main Menu Push EXIT to return on the Status display Audio settings The Audio settings menu allows to configure the audio output.
MPR30-IEM User Manual Rev. 06 Edit RX The Edit RX menu allows to configure the radio frequency settings. PARAMETER Gr-Ch Frequency Squelch SETTING 0÷39 groups 0÷59 channels 470÷700 MHz for MPR30-IEM-N 566÷798 MHz for MPR30-IEM-M OFF or 0/3/6/9/12/ 15/18/21/ 24/28/32/ 36/40/46dBuV MEANING Select current group and channel. Group name and channel frequency are displayed on the right. If the specific group/channel is not locked, the frequency can be edited in this menu.
MPR30-IEM User Manual Rev. 06 “Scan now” menu The following table lists the three types of scans that can be performed Once started a Channel scan operation the receiver asks for group to be used*. Press and hold the SEL button to select the group to scan. Then it prompts to turn off all transmitters. So press SEL to start the scan! Channel After few seconds, scan results are displayed sorted by level, making easier to pick up the best one. The dotted line in the graph indicate the squelch threshold.
MPR30-IEM User Manual Rev. 06 After few seconds, scan results are displayed on a histogram. Each column of the histogram is divided into two parts by a black line. The lower part indicates the number of free channels (RF level < Squelch level - 6dBµV) in the group, while the upper one the number of channels almost free (Squelch level < RF level < Squelch level - 6dBµV). We recommend to choose the group with the highest number of free channels.
MPR30-IEM User Manual Rev. 06 Settings The Settings menu allows to configure main settings of the device. PARAMETER SETTING MEANING The name menu allows to change the name of the receiver. This is the name displayed in the top of the Status display and it is the name sent to the 12 case-sensitive alphanumeric transmitter with the sync function (for the Name characters transmitter with this advanced capability).
MPR30-IEM User Manual Rev. 06 Sync The SYNC function is useful to tune a transmitter on the same frequency of the receiver via the IR interface. Before starting the sync function tune the receiver on desired channel, manually or using the SCAN utility. After this, enable the IR interface on the transmitter. Now press UP&EXIT buttons together or enter in the Sync menu to start the SYNC function.
MPR30-IEM User Manual Rev. 06 How to add a clone Out mode Balance Equalizer Vol boost Pilot tone Gr-Ch Squelch RX Name Clone name Enable the IRDA interface on the RX from which take the configuration (Infrared menu) Put the receivers face to face At the end of the process the name of the clone will be identify with the name of the receiver. Enter in the Add menu and select the wanted clone number. Then push SEL to start the IRDA communication.
MPR30-IEM User Manual Rev. 06 Loading a clone, all the clone parameters are set on the receiver. The follow icon appears on the right of the display indicating that a clone is loaded. The number and the name of the clone are displayed on the top of the display menu and a brief list of the main parameters are displayed on the status menu.
MPR30-IEM User Manual Rev. 06 Preset This menu allows to load/save 6 user presets or load the Factory configuration. PARAMETER SETTING Restore 1/2/3/4/5/6/Factory Save 1/2/3/4/5/6 MEANING Select the Restore submenu and chose the presets to load: user presets or Factory preset. Push and keep SEL button to load the preset. Select the Save submenu and chose the user presets to save. Push and keep SEL button to save the preset ERROR LIST When an error occurs, the receiver A.
MPR30-IEM User Manual Rev.
MPR30-IEM User Manual The frequencies of all the channels and groups is equal to the lower frequency of the receiver Error in the channel memory during the initialization phase. (according to the receiver 470 MHz for MPR30-IEM-N 566 MHz for MPR30-IEM-M) Configuration mismatch Error in the parameter memory Rev.
MPR30-IEM User Manual Rev.
MPR30-IEM User Manual Rev. 06 HOW TO USE MPR30 RX MANAGER Wisycom MPR30 RX Manager can be used to load or save the channels memory and upgrade the firmware. Instruction to connect MPR30 using UPK300 / UPK300E: 1. 2. 3. 4. 5. 6. 22 Connect to the PC the infrared programming interface (UPK300 or UPK300E) using a USB cable (NOTE: it is not possible to use IR interface of MRK950 or MRK960) Check if the version of ENG RX Manager installed in your PC is the latest version.
MPR30-IEM User Manual 7. 23 Rev.
MPR30-IEM User Manual Rev. 06 Instruction to connect MPR30 using USB cable: In order to use the micro USB port to configure the MPR30, it is necessary to install the MPR30 USB driver (see How to install MPR30 USB driver) 1. 2. 3. 4. 5. Connect the MPR30 to the PC through the micro USB interface using the USB cable Check if the version of ENG RX Manager installed in your PC is the latest version.
MPR30-IEM User Manual Rev. 06 How to load/save channels memory Write: Push the button Write from WDF file… and select the wdf file to load on the MPR30. Read and save: Push the button Read and save to WDF file… , insert the .wdf file name and the path where to save the wdf file. During the process of writing/reading & saving, a green bar below the panel shows the progress of the process and on the information panel it is possible to verify what the application is doing.
MPR30-IEM User Manual Rev. 06 TECHNICAL SPECIFICATIONS • Frequency ranges • Switchable channels • Switching-window • Frequencies • Frequency error • Temperature range • Modulation • Peak deviation • “A” / “B” antenna in • Antenna input imp. • Sensitivity • Co-channel rejection • Adjacent chan. Sel. • Spurious rec. Rej. • IF image rejection • Intermod.
MPR30-IEM User Manual MECHANICAL DRAWING Note: unit is mm 27 Rev.
MPR30-IEM User Manual 28 Rev.
MPR30-IEM User Manual Rev. 06 ITALY ONLY Obblighi di informazione agli utilizzatori Modello di informazioni agli utenti dei prodotti di tipo “professionale” INFORMAZIONE AGLI UTENTI ai sensi dell’art. 13 del Decreto Legislativo 25 luglio 2005, n.
MPR30-IEM User Manual 30 Rev.
MPR30-IEM User Manual Wireless System Communications Via Spin 156 I-36060 Romano d’Ezzelino Italy Tel. +39 -0424 -382605 Fax +39 - 0424 - 382733 www.wisycom.com e-mail: sales@wisycom.com 31 Rev.
