LV65B Indoor/Outdoor CPE User Guide (LV65B)
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Caution Ensure to connect the power cord of the power adapter to a socket outlet with an earthing connection. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Installation Statement Installation of the device must be carried out by professional, trained technicians.
Chapter 1 Introduction Unboxing Information/Product Package Inside the product package for the LV65B CPE you should find the following items: Outdoor (Device package): Items Quantity Power adapter 1 IDU Kit (Separate from device package) Items Quantity Indoor bracket 1 Screws & anchors (indoor) 2 of each Window wipe 1 Window wedge 2 Device rear cover 1 Device rear cover/IO cover screw pack 4 of each IO cover 1 Items Quantity J-pole (wood screw included) 1 ODU bracket 1 Hose clamp
Product Overview Indoor:
Outdoor: IO cover Cable gland Front side Side view LED Label Bottom side J-pole screw (2 pcs) Back side GND screw
Outdoor: SIM slot cover (Material: rubber) I/O cap Remove the I/O cap to access the SIM slot cover SIM slot cover (Material: rubber) Remove the SIM slot cover to insert/remove a SIM card or Micro USB card.
PSE Adapter: Ethernet Ports on the side of the PSE Adapter
J-Pole Installation Step 1: • Adjust pole angle to best meet base station direction. • Tighten 2 elbow nut to fix the angle: Torque: 140 +/-10 kgf-cm Torque: 10.12 +/-0.72 lbf-ft • Step 2: Detail of the elbow screw is shown in next page.
5 mm • Hang the ODU device on the J-Pole • Tightening two HEXI screw after ODE hang in place (screw had pre-mounted with j-pole already) Torque: 60 +/-10 kgf-cm Torque: 4.32 +/-0.
Unit: mm • Tighten 4 screws to fix the base bracket onto the wall. • Screw information: Screw Type: ¼”x2” Wood Screw Screw Head: HEX head Step 5: • (If need) Loosen 2 nuts and re-adjust pole angle to best meet base station direction. • Tighten 2 elbow nut to fix the angle: Torque: 140 +/-10 kgf-cm Torque: 10.12 +/-0.
Finish the waterproof cable gland setup as below: Note: For ODU installation, please use the RJ45 cable without latch jacket.
Indoor Installation (Glass Window Mounting) Step 1: Signal scanning Hold the Verizon Receiver close to the window to perform signal scanning (hold the device at a height above your head when doing so). Once a location with good signal strength is found, the LED on the device will turn solid white. Affix a location sticker to the spot on the window glass where the device will be mounted (the location stickers can be found on the side of the device’s cover).
Step 3: Peel off the protective film from the Gecko tape on the indoor bracket, and then affix the indoor bracket on the window in the orientation shown below. Protective film Step 4: Use both thumbs to apply solid pressure in all areas where Gecko tape makes contact with the glass to ensure a secure installation. Whenever possible, check the adhesion by looking at the bracket from the outside in.
Note: If, after installation, the bracket is not horizontal, you can use the lazy Susan feature to adjust the orientation of the bracket.
Step 5: Once the indoor bracket is securely affixed to the window, align the bracket slot on the IDU with the bracket arms on the bracket, then push the device into the bracket until a “click” sound is heard. Step 6: Adjust the orientation of the device until its top and sides are perfectly horizontal or vertical. Refer to the image on the bottom right for the correct orientation.
Indoor Installation (Glass Window Mounting) Step 1: Signal scanning Hold the Tri-band - 5G Business Internet Receiver near different locations on the wall to perform signal scanning (hold the device at a height above your head when doing so). Once a location with good signal strength is found, the LED on the device will turn solid white. Affix a location sticker to the spot.
Step 3: Drill installation holes and install the bracket Use a power screwdriver to drill holes in the marked locations, then take two wall anchors and place them into the holes (make sure the tops of the anchors are flush with the wall). Step 4: Install bracket Align the holes on the indoor bracket with the wall anchors, then take two screws from the indoor wall screw pack and screw them into the wall anchors.
LED and Audio Behavior Receiver LED Definition: Status PWR LED Sound Boot up Power On / Normal Operating Mode Solid White Not Applicable Bluetooth Pairing BT (Shows for 60 seconds or until the device is paired) Cyan to OFF to Green to OFF (switch every 200 ms) Not Applicable BT connection successful Cyan blinking (200 ms ON, 200 ms OFF) × 3 Not Applicable BT connection failure Red blinking (200 ms ON, 200 ms OFF) × 3 Not Applicable Changing modes manually Changing from installation mode to regula
Internet available Solid White, Internet APN is available Not Applicable Internet not available Solid Red, Internet APN is not available Not Applicable Internet disabled through device settings Amber blinking (600 ms ON, 600 ms OFF) until Internet's available Not Applicable Status Connectivity LED Sound Cellular Connectivity mmWave Connectivity Solid White, Blink for Operation/Search Mode. Not Applicable Sub-6 Connectivity Solid Cyan, Blink for Operation/Search Mode.
Reset Button Button press duration Function Hold (>3 seconds) Switch between installation mode and regular usage mode Hold (1-2 seconds) Restores device to factory settings Single click (<1 second) Resets the device’s smart antenna (this needs to be done before any subsequent signal scans after the first one) Chapter 2 Product Specifications Bands 5G mmWave: n261 / n260 5G Sub-6: n2, n5, n48, n66, n77 4G: B2, B5, B13, B48, B66 Memory MCP (1 GB LPDDR4 + 1 GB NAND) Dimensions 9
