ScopeCam 2 Microscope Digital Camera USER MANUAL Version 2.0 USB 2.
User Manual Trademark and copyright information © Copyright 2005, WISE DIGITAL Technology Co., Ltd.(WISE DIGITAL) All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of WISE DIGITAL Technology Co., Ltd. The information contained in this document is subject to change without notice. WISE DIGITAL Technology Co., Ltd.
User Manual Warnings and Precautions Precautions when using your ScapeCam Keep camera away from the following: ・ High temperatures and excessive humidity ・ Direct sunlight or other heat sources ・ Dust ・ Extreme vibration If the imaging sensor lens becomes dirty, first try blowing dust particles from it. Next use a lint free cloth or proper lens cleaning cloth to wipe the lens gently. Only use approved lens cleaning fluids.
User Manual System Requirements PC running either Windows ® 2000 or XP (Professional-SP4) -XP (Professional-SP2) are installed when shipping ,No working if specifications up to reach of above after shipment ٛ DirectX 9.0 or later installed ٛ 1.2 GHz minimum processor ٛ USB 2.0 Port ٛ CD-ROM drive ٛ 128 MB RAM ٛ 100 MB Free HDD ٛ Performance is dependent on the PC's graphics card. USB 2.0 is only supported on Windows ® XP and 2000. Do not try to use any other Microsoft ® operating system.
User Manual Package Contents 1 x Camera with USB 2.0 Cable 1 x CD-ROM (Driver & Software ) Ø30.0mm Ø30.5mm 2 x Ocular Adapters for stereomicroscope If there are any parts missing from your package, please contact your dealer.
User Manual Installing the Software Insert the CD-ROM into your drive. Do not connect your camera at this point yet. You will be asked to do so later. The installation program should auto-run. If the program does not auto-run then you need to run the setup.exe from the CD-ROM. To do this, go to “My Computer” and right-click on the CD Drive and choose “Open” or“Explore”: this will show you the contents of the CD-ROM where you can double click the“autorun” icon in order to run it.
User Manual Trouble Shooting WARNING: Please do not attempt to open the camera case. There are no user serviceable parts inside. “No Compatible Camera was detected” error dialog box appears when trying to open software: If an error message appears similar to this. The software did not detect any compatible devices and therefore will not open. Check the device is plugged in correctly. This error could mean that the camera is not connected properly, drivers are not installed correctly and/or that the USB2.
User Manual Technical Data 350K-USB2.0 1/4” CMOS Sensor 350K ・ 640 x 480 high resolution mode ・ 320 x 240 low resolution mode ・ USB 2.0 ・ 30 fps high resolution ・ 40 fps low resolution 1.3M-USB2.0 1/2” CMOS Sensor 1.3M ・ 1280 x 1024 high resolution mode ・ 640 x 480 low resolution mode ・ USB 2.0 ・ 15 fps high resolution ・ 30 fps low resolution 3M-USB2.0 1/2” CMOS Sensor 3M ・ 2048x 1536 high resolution mode ・ 800 x 600 low resolution mode ・ USB 2.
User Manual Warranty WISE DIGITAL Technology Co., Ltd. Limited 12-Month Product Warranty WISE DIGITAL warrants this product against defects in materials and workmanship for 12 months. If a defect is discovered, WISE DIGITAL will, at its option, repair or replace the product at no charge provided it is returned during the warranty period, with transportation charges prepaid, to the authorized WISE DIGITAL dealer from whom you purchased the product. Proof of purchase may be required.
