Cut Sheet

Catalog No./Item Description/Specifications
RC7ATCGY* Assembled Unit – Prewired
RC7ATCBK* 20A duplex receptacle can
RC7ATCAL*
be wired as standard duplex
RC7ATCBS* or isolated ground. Wiremold
RC7ATCVY* Open System unloaded inserts
RC7ATCAB* to accept two discrete keystone
RC7ATCAA* connectors from most
manufacturers are provided.
Includes 2 Cat 6 TechChoice
™
discrete keystone connectors and
Ortronics
®
TracJack bezels.
RC7SHTCBK Nonmetallic Slide Holder
RC7SHTCGY Assembly – Available in black
RC7SHTCBS (BK), gray (GY), ivory (VY),
RC7SHTCVY and nonmetallic brass (BS).
RC7SHTCBKCR
Poke-Thru Controlled Receptacle –
RC7SHTCBSCR Nonmetallic Slide Holder Assembly
RC7SHTCGYCR with Controlled Receptacle
RC7SHTCAACR Markings. Markings are located in
RC7SHTCVYCR a recess pad and are permanent
indicating the duplex receptacle
below has been wired up to comply
with 2014 NEC
®
, CA Title 24 and
ASHRAE Energy Efficiency
Standard 90.1. Available in
black (BK), brass (BS), gray (GY),
aluminum (AA) and. ivory (VY).
Slide holder to be used with
RC7ATC and RC7CTC units.
4
Catalog No./Item Description/Specifications
RC7STC Insert Assembly with Disposable
Plate – Use with RC7C Series
Covers to complete installation.
RC7CTCGY* Finish Flange and Slide
RC7CTCBK* Holder Assembly – Prewired
RC7CTCAL* 20A duplex can be wired as
RC7CTCBS* standard duplex or isolated
RC7CTCVY* ground.
Wiremold Open
RC7CTCAB*
system unloaded inserts to accept
RC7CTCAA* two discrete keystone connectors
from most manufacturers are
provided. Includes 2 Cat 6
TechChoice
™
discrete keystone
connectors and Ortronics
®
TracJack adapters.
RC7KTCGY* Retrofit Kit – Used to upgrade
RC7KTCBK* existing installations of RC7
RC7KTCAL* Poke-Thru Devices on carpet floors
RC7KTCBS* to meet scrub water requirements.
Includes 20A duplex receptacle
that can be wired as a standard
duplex or isolated ground, two
Category 6 TechChoice
™
discrete
keystone connectors, and two
Ortronics TracJack mounting
bezels. Also includes scrub water
finish flange and slide holder
assembly. Kit also includes duplex
receptacle barrier. Old barrier
must be replaced with new. See
installation instructions with retrofit
kit for complete installation details.
RC7 Series Ordering Information
7"
(178mm)
16 1/2"
(419mm)
16 1/2"
(419mm)
7"
(178mm)
* Poke-Thru Devices on this page are available in some or all of the
following cover color options as indicated by the part numbers:
GY – Gray painted flange with gray nonmetallic cover,
BK – Black painted flange with black nonmetallic cover,
VY – Ivory painted flange with ivory nonmetallic cover,
AL – Brushed Aluminum flange with black nonmetallic cover
BS – Brushed Brass flange with black nonmetallic cover
AA – Brushed Aluminum flange with aluminum-colored nonmetallic cover
AB – Brushed Brass flange with brass-colored nonmetallic cover
Where applicable, slide covers match the cover color.
5"
(127mm)
NOTE: Assembled with scrub water gasket.
For use on tile or carpet floors.
7"
(178mm)
3 1/16" HOLE SIZE POKETHRU DEVICES
CAUTION: Not intended for use
on polished concrete
or terrazzo floor
applications.
CAUTION: Not intended for use
on polished concrete
or terrazzo floor
applications.
Catalog Number Explanation RC7ATCAL
RC7 A TC AL
Identifies Identifies Identifies that Unit Identifies Color of
Poke-Thru Series Assembled Unit (A) is approved for Tile Cover Assembly
or Cover (C) and Carpet Floors (See below )