iRespond®- UltraLite Technical Manual Wireless eSystems
Table of Contents Lite Base Unit --------------------------------------------------------------- 1 Change the Channel --------------------------------------------------1 Adjust Power Output -------------------------------------------------1 Turn On/Off Channel Scan ----------------------------------------- 2 Setting Base UID -----------------------------------------------------2 Adjusting Base Offset ----------------------------------------------- 3 Turn on in Programming Mode ------------------------------
UltraLite/Lite Base Unit Change the Base’s Channel 1. Press the power button 2. Immediately press F1 screen. to turn on the Lite base. while Wireless eSystems scrolls across the base’s 3. When Device Address appears press ENT altered). 4. Select ENT . (This number should not be at Output Power. 5. Output Channel should now be displayed. 6. Use the up 7. Press ENT and down buttons to change the base’s channel. four more times to save and exit configuration mode. 8.
Turning Channel Scan On/Off It is best for the base and remote units to be on the same channel. However, channel scanning can be used to allow the base unit to find the best channel with the least amount of noise. To communicate with a base with channel scanning on, remote units must be configured with channel hopping on. 1. Press the power button 2. Immediately press F1 screen. to turn on the Lite base. while Wireless eSystems scrolls across the base’s 3. When Device Address appears press ENT altered).
. Use the up and down buttons to change the number. Adjusting Base Offset The Offset is the center frequency for all remote radios, ensuring base can communicate with all remotes. The Lite base’s Offset is set before it is shipped and should never be changed. 1. Press the power button to turn on the Lite base. 2. Immediately press F1 screen. while Wireless eSystems scrolls across the base’s 3. Device Address should be displayed. 4. Press ENT three times. Base will read Offset 1. 5.
UltraLite Remote Unit To Login by PIN An iRespond session must be running to login to a remote. 1. Press the power button to turn on the UltraLite remote. 2. Use the A-E Buttons to enter the correct characters of your PIN. 3. If the PIN was entered incorrectly, the right light will blink red once. 4. Renter your PIN. (If you fail to log in again, verify your PIN with the instructor) To Login Anonymously Instructor must have the iRespond session set up to allow anonymous logins. 1.
1. Select the appropriate A-E button(s). 2. To change a response, select the same response press the button for the new correct response. 3. Press SEND button again, then to go to the next question or to submit your answer. To Answer Fill-in/Short/Essay Response Questions Note: Lites are capable of answering numerical answers for Fill-in questions ONLY. 1. Use the numeric question. keypad to enter in the correct response to the Fill-in 2. To change a response, use the Left answer. 3.
7. To delete homework and enter in new homework use the Up and Down arrows to Erase? Yes and press SEND . 8. Use the response buttons to enter in responses for MultipleChoice/Response questions. 9. Use the numeric keypad to enter in responses for Fill-In questions. 10. Press SEND to go to the next question. 11. When all homework has been entered press the F1 button again. 12. The remote will display Logout? No. Use the Up and Down change it to Logout? Yes. arrows to 13. Press SEND .
. The remote will display Logout? No. Use the Up and Down change it to Logout? Yes. arrows to . The homework will be saved and the remote will return 10. Press SEND to the PIN? screen. To Review Answers During a Session Not available during Instructor-Paced sessions. 1. Use the Up responses. arrow or the SEND button to scroll through the 2. Students may go to a specific question by selecting Go number they wish to return to. and then the 3.
Turning Channel Hop On/Off It is best for the base and remote units to be on the same channel. However, channel hopping can be used to allow the remote unit to cycle through all available channels to find a base on any channel. This is useful when using multiple bases that are set to different channels. 1. Press the power button 2. Press the Flag to turn on the Lite remote. button. 3. Press 2 from the numeric keypad and press SEND 4.
2. Press the Flag button. 3. Press 2 from the numeric keypad and press SEND . 4. When Address is displayed on the screen press SEND should never be changed). 5. At Power press SEND . (This number . . 6. At Channel press SEND 7. When “Debug” displays on the remote screen use the Up and Down arrows to turn the Automaton on (yes) or off (no). 8. Press SEND twice to save and turn off the remote. Turn Remote on in Programming Mode 1. Press and hold the F1 button. 2.
4. The remote will display Config Mode. 5. When the remotes have been configured they will automatically power down. Check a Remote’s UID/Version To check what version a remote has or to check the channel a remote is set to follow these steps. 1. Press the power button 2. Press the Flag to turn on the Lite remote. button. 3. Select 1 from the numeric keypad and press SEND . 4. L101 will display on the remote. The number beside it is the current version the remotes have. 5.
Play Games 1. Press the power button 2. Press the Flag to turn on the Lite remote. button. 3. Select 6 from the numeric keypad and press SEND . 4. There are four games to choose from. Option 1: Number Crunch In this game students solve math problems. 1. The remote will display addition, subtraction, multiplication, and division problems. Enter in the correct response with the numeric keypad answer and press SEND to to go to the next problem. 2.
Option 3: Word Scramble In this game users have to unscramble a word. 1. The remote will display a scrambled word. 2. Users will use the Up and Down letter, then they will press SEND arrows to select the correct to move to next letter. Option 4: Vegas Slots 1. The first line of the remote will display the amount of money you currently have to gamble. 2. The next line shows “Bet? 123.” 3. You may choose to bet 1, 2, or 3 dollars using the numeric keypad . 4. After selecting 1, 2 or 3.
