Cambium PMP 450 Operations Guide System Release 12.
PMP 450 module essential information Table 1 PMP 450 module essential information Default IP Address for Management GUI Access 169.254.1.1 Default Administrator Username admin Default Administrator Password (no password) Software Upgrade Procedure See ―Updating the software version and using CNUT‖ in the PMP 450 Configuration and User Guide 1. On the radio GUI, navigate to Configuration, Unit Settings and select Set to Factory Defaults OR Resetting the Module to Factory Defaults (2 options) 2.
Accuracy While reasonable efforts have been made to assure the accuracy of this document, Cambium Networks assumes no liability resulting from any inaccuracies or omissions in this document, or from use of the information obtained herein.
PMP 450 Operations Guide Safety and regulatory information Safety and regulatory information This section describes important safety and regulatory guidelines that must be observed by personnel installing or operating PMP 450 equipment. Important safety information To prevent loss of life or physical injury, observe the safety guidelines in this section. Power lines Exercise extreme care when working near power lines. Working at heights Exercise extreme care when working at heights.
PMP 450 Operations Guide Safety and regulatory information RF exposure near the antenna Radio frequency (RF) fields will be present close to the antenna when the transmitter is on. Always turn off the power to the PMP 450 unit before undertaking maintenance activities in front of the antenna. Minimum separation distances Install the AP/SM so as to provide and maintain the minimum separation distances from all persons.
Contents PMP 450 Operations Guide Contents PMP 450 module essential information .......................................................................................................... 2 Safety and regulatory information .......................................................................... i Important safety information................................................................................................................... i Important regulatory information................................
PMP 450 Operations Guide Contents RADIUS Device Data Accounting ..................................................................................................... 2-29 RADIUS Device Re-Authentication .................................................................................................. 2-33 RADIUS Attribute Framed-IP-Address ............................................................................................
Contents PMP 450 Operations Guide Interpreting RF Control Block Statistics in the Radio Tab (All) ....................................................... 4-27 Interpreting Data in the VLAN Tab (ALL) ....................................................................................... 4-28 Viewing Data VC Statistics (All) ........................................................................................................ 4-29 Viewing Summary Information in the Overload Tab (All) .....................
PMP 450 Operations Guide Contents Compliance with safety standards ............................................................................................................... 8-9 Electrical safety compliance ................................................................................................................. 8-9 Electromagnetic compatibility (EMC) compliance ............................................................................... 8-9 Human exposure to radio frequency energy ........
List of Figures PMP 450 Operations Guide List of Figures Figure 1 Uplink and downlink rate caps adjusted to apply aggregate cap ......................................................... 2-3 Figure 2 Quality of Service (QoS) tab of the AP ............................................................................................... 2-8 Figure 3 Diffserv tab of the AP .......................................................................................................................
PMP 450 Operations Guide List of Figures Figure 38 Remote Spectrum Analyzer tab of the AP ........................................................................................ 5-6 Figure 39 Alignment Tool tab of SM, good link example .................................................................................. 5-7 Figure 40 Alignment Tool tab of SM, acceptable link example .........................................................................
List of Tables PMP 450 Operations Guide List of Tables Table 1 PMP 450 module essential information ................................................................................................... 2 Table 2 Characteristics of traffic scheduling ....................................................................................................... 2-5 Table 3 Recommended combined settings for typical operations .......................................................................
PMP 450 module essential information PMP 450 Operations Guide Table 38 SM specifications ................................................................................................................................ 8-4 Table 39 PMP 450 wireless specifications .......................................................................................................... 8-7 Table 40 Ethernet bridging specifications ..............................................................................................
PMP 450 Operations Guide About This Operations Guide About This Operations Guide This guide discusses the techniques to maintain and grow a PMP 450 network.
General information PMP 450 Operations Guide General information Version information The following shows the issue status of this document since it was first released: Issue Date of issue Remarks 001v000 September 2012 System Release 12.0 Contacting Cambium Networks PMP support website: http://www.cambiumnetworks.com/support Cambium main website: http://www.cambiumnetworks.com/ Sales enquiries: solutions@cambiumnetworks.com Email support: support@cambiumnetworks.
PMP 450 Operations Guide General information Purpose Cambium Networks Point-To-Multipoint (PMP) documents are intended to instruct and assist personnel in the operation, installation and maintenance of the Cambium PMP equipment and ancillary devices. It is recommended that all personnel engaged in such activities be properly trained.
Problems and warranty PMP 450 Operations Guide Problems and warranty Reporting problems If any problems are encountered when installing or operating this equipment, follow this procedure to investigate and report: 1 Search this document and the software release notes of supported releases. 2 Visit the support website. http://www.cambiumenetworks.com/support/pmp/software/index.php 3 Ask for assistance from the Cambium product supplier.
PMP 450 Operations Guide Problems and warranty Portions of Cambium equipment may be damaged from exposure to electrostatic discharge. Use precautions to prevent damage.
Security advice PMP 450 Operations Guide Security advice Cambium Networks systems and equipment provide security parameters that can be configured by the operator based on their particular operating environment. Cambium recommends setting and using these parameters following industry recognized security practices. Security aspects to be considered are protecting the confidentiality, integrity, and availability of information and assets.
PMP 450 Operations Guide Warnings, cautions, and notes Warnings, cautions, and notes The following describes how warnings and cautions are used in this document and in all documents of the Cambium Networks document set. Warnings Warnings precede instructions that contain potentially hazardous situations. Warnings are used to alert the reader to possible hazards that could cause loss of life or physical injury.
PMP 450 Operations Guide Redeploying Modules Chapter 1: Growing Your Network Keys to successfully growing your network include monitoring the RF environment. considering software release compatibility. redeploying modules appropriately and quickly. Monitoring the RF environment Regardless of whether you are maintaining or growing your network, you may encounter new RF traffic that can interfere with your current or planned equipment.
Warnings, cautions, and notes PMP 450 Operations Guide o software compatibility. For example, whether desired features can be enabled with the redeployed module in the network. o hardware compatibility; for example, where a CMMmicro is deployed. o the value of each configurable parameter. Whether all are compatible in the new destination.
PMP 450 Operations Guide Managing Bandwidth and Authentication Chapter 2: Managing Bandwidth and Authentication This section provides a high-level description of bandwidth and authentication management in a network, and includes the following sections: Configuring quality of service on page 2-2 describes the Quality of Service (QoS) mechanisms implemented in the PMP 450 system. Configuring a RADIUS server on page 2-15 describes how to integrate a RADIUS server into a PMP 450 management network.
Configuring quality of service PMP 450 Operations Guide Configuring quality of service Maximum Information Rate (MIR) Parameters Point-to-multipoint links use the following four MIR parameters for bandwidth management: Sustained Uplink Data Rate (kbps) Uplink Burst Allocation (kb) Sustained Downlink Data Rate (kbps) Downlink Burst Allocation (kb) You can independently set each of these parameters per AP or per SM.
PMP 450 Operations Guide Interaction of Burst Allocation and Sustained Data Rate Settings Maximum Information Rate Data Entry Checking Uplink and downlink MIR is enforced as shown in Figure 1. In these figures, entry refers to the setting in the data rate parameter, not the burst allocation parameter.
Configuring quality of service PMP 450 Operations Guide High-priority Bandwidth To support low-latency traffic such as VoIP (Voice over IP) or video, the system implements a highpriority channel. This channel does not affect the inherent latencies in the system but allows highpriority traffic to be immediately served. The high-priority pipe separates low-latency traffic from traffic that is latency tolerant, such as standard web traffic and file downloads.
PMP 450 Operations Guide Traffic Scheduling This tab in the AP sets the priorities for the various packets in the downstream (sent from the public network). This tab in the SM sets the priorities for the various packets in the upstream (sent to the public network). Typically, some SMs attach to older devices that use the ToS byte as originally formatted, and others to newer devices that use the DSCP field.
Configuring quality of service PMP 450 Operations Guide Packets that have a priority of 4 to 7 in either the DSCP or a VLAN 802.1p tag are automatically sent on the high-priority channel, but only where the high-priority channel is enabled. Setting the Configuration Source The AP includes a Configuration Source parameter, which sets where SMs that register to the AP are controlled for MIR, VLAN, and the high-priority channel as follows.
PMP 450 Operations Guide Setting the Configuration Source Table 4 Where feature values are obtained for an SM with authentication required Configuration Source Setting in the AP Values are obtained from MIR Values VLAN Values High Priority Channel State Authentication Server Authentication Server Authentication Server Authentication Server SM SM SM SM Authentication Server+SM Authentication Server Authentication Server, then SM Authentication Server, then SM NOTES: HPC represents the Hi Pr
Configuring quality of service PMP 450 Operations Guide Quality of Service (QoS) Tab of the AP Figure 2 Quality of Service (QoS) tab of the AP In the Quality of Service (QoS) tab, you may set AP bandwidth parameters as follows. Table 6 AP QoS attributes Attribute Meaning Sustained Uplink Data Rate Specify the rate that each SM registered to this AP is replenished with credits for transmission. This default imposes no restriction on the uplink.
PMP 450 Operations Guide Quality of Service (QoS) Tab of the AP Attribute Meaning Downlink Burst Allocation Specify the maximum amount of data to allow the AP to transmit to any registered SM before the AP is replenished with transmission credits at the Sustained Downlink Data Rate.
Configuring quality of service PMP 450 Operations Guide DiffServ Tab of the AP Figure 3 Diffserv tab of the AP You may set the following Diffserv tab parameters. Table 7 AP Diffserv attributes Attribute CodePoint 1 through CodePoint 47 2-10 Meaning Priorities of 0 through 3 map to the low-priority channel; 4 through 7 to the high-priority channel. The mappings are the same as 802.1p VLAN priorities.
PMP 450 Operations Guide Quality of Service (QoS) Tab of the SM Attribute Meaning PPPoE Control Message Priority Operators may configure the AP to utilize the high priority channel for PPPoE control messages. Configuring the AP in this fashion can benefit the continuity of PPPoE connections when there are issues with PPPoE sessions being dropped in the network. This prioritization may be configured in the DiffServ tab in the Configuration menu of the AP.
Configuring quality of service PMP 450 Operations Guide Attribute Meaning Sustained Downlink Data Rate Specify the rate at which the AP should be replenished with credits (tokens) for transmission to this SM. This default imposes no restriction on the uplink.
PMP 450 Operations Guide DiffServ Tab of the SM DiffServ Tab of the SM Figure 5 Diffserv tab of the SM pmp-0049 (September 2012) 2-13
Configuring quality of service PMP 450 Operations Guide In the Diffserv tab of the SM, you may set the following parameters. Table 9 SM Diffserv attributes Attribute CodePoint 1 through CodePoint 47 CodePoint 49 through CodePoint 55 CodePoint 57 through CodePoint 63 CodePoint Select 2-14 Meaning Priorities of 0 through 3 map to the low-priority channel; 4 through 7 to the high-priority channel. The mappings are the same as 802.1p VLAN priorities.
PMP 450 Operations Guide Configuring a RADIUS server Configuring a RADIUS server Configuring a RADIUS server in a PMP 450 network is optional, but can provide added security, increase ease of network management and provide usage-based billing data.
Configuring a RADIUS server PMP 450 Operations Guide Note, Aradial 5.3 has a bug that prevents ―remote device login‖, preventing usage of the user name and password management features. Choosing Authentication Mode and Configuring for Authentication Servers - AP On the AP‘s Configuration > Security tab, select the RADIUS AAA Authentication Mode. The following describes the other Authentication Mode options for reference, and then the RADIUS AAA option. Disabled: Requires no authentication.
PMP 450 Operations Guide Configuring a RADIUS server Figure 6 Security tab of the AP pmp-0049 (September 2012) 2-17
Configuring a RADIUS server PMP 450 Operations Guide SM Authentication Mode – Require RADIUS or Follow AP If it is desired that an SM will only authenticate to an AP that is using RADIUS, on the SM‘s Configuration Security tab set Enforce Authentication to AAA. With this enabled, an SM will not register to an AP that has any Authentication Mode other than RADIUS AAA selected.
PMP 450 Operations Guide Configuring a RADIUS server Figure 7 Security tab of the SM pmp-0049 (September 2012) 2-19
Configuring a RADIUS server PMP 450 Operations Guide SM - Phase 1 (Outside Identity) parameters and settings The protocols supported for the Phase 1 (Outside Identity) phase of authentication are eapttls (Extensible Authentication Protocol Tunneled Transport Layer Security) and eapMSChapV2 (Extensible Authentication Protocol – Microsoft Challenge-Handshake Authentication Protocol). Configure an outer Identity in the Username field.
PMP 450 Operations Guide Configuring a RADIUS server Up to 2 certificates can be resident on an SM. An installed certificate can be deleted by clicking the Delete button in the certificate‘s description block on the Configuration > Security tab. To restore fhe 2 default certificates, click the Use Default Certificates button in the RADIUS Certificate Settings parameter block and reboot the radio.
Configuring a RADIUS server PMP 450 Operations Guide Configuring your RADIUS servers for SM authentication Your RADIUS server will need to be configured to use the following: EAPTTLS or MSCHAPv2 as the Phase 1/Outer Identity protocol. If Enable Realm is selected on the SM‘s Configuration > Security tab, then the same Realm as appears there (or access to it). The same Phase 2 (Inner Identity) protocol as configured on the SM‘s Configuration > Security tab under Phase 2 options.
PMP 450 Operations Guide Configuring a RADIUS server Assigning SM management IP addressing via RADIUS Operators may use a RADIUS AAA server to assign management IP addressing to SM modules (framed IP address). SMs now interpret attributes Framed-IP-Address, Framed-IP-Netmask, and Cambium-Canopy-Gateway from RADIUS. The RADIUS dictionary file has been updated to include the Cambium-Canopy-Gateway attribute and is available on the Cambium Software Support website.
Configuring a RADIUS server PMP 450 Operations Guide Configuration > Quality of Service > Downlink Burst Allocation Cambium-Canopy26.161.14 VLLEARNNEN Configuration > VLAN > Dynamic Learning integer N Cambium-Canopy-VLFRAMES 26.161.15 integer N 1 Configuration > VLAN > Allow Frame Types Cambium-Canopy-VLIDSET 26.161.16 integer N 26.161.20 Configuration > VLAN > VLAN Aging Timeout Cambium-Canopy-VLIGVID 26.161.21 Configuration > VLAN > Default Port VID Cambium-Canopy-VLMGVID 26.161.
PMP 450 Operations Guide Configuring a RADIUS server Using RADIUS for centralized AP and SM user name and password management AP – Technician/Installer/Administrator Authentication To control technician, installer, and administrator access to the AP from a centralized RADIUS server: 1 Set Authentication Mode on the AP‘s Configuration > Security tab to RADIUS AAA 2 Set User Authentication Mode on the AP‘s Account > User Authentication tab (the tab only appears after the AP is set to RADIUS authenticatio
Configuring a RADIUS server PMP 450 Operations Guide Figure 9 User Authentication tab of the AP SM – Technician/Installer/Administrator Authentication To control technician, installer, and administrator access to the SM from a centralized RADIUS server: 1 Set Authentication Mode on the AP‘s Configuration > Security tab to RADIUS AAA (RADIUS) 2 Set User Authentication Mode on the AP‘s Account > User Authentication and Access Tracking tab (the tab only appears after the AP is set to AAA authentication)
PMP 450 Operations Guide Configuring a RADIUS server Note, remote access control is enabled only after the SM registers to an AP that has Authentication Mode set to RADIUS AAA. Local access control will always be used before registration and will be used after registration if the AP is not configured for RADIUS. igure 10 User Authentication and Access Tracking tab of the AP Table 11 AP User Authentication and Access Tracking attributes Attribute Meaning • Local: The local SM is checked for accounts.
Configuring a RADIUS server PMP 450 Operations Guide Attribute Meaning Radius Accounting Port The destination port on the AAA server used for Radius accounting communication. disable – no accounting messages are sent to the RADIUS server Accounting Messages deviceAccess – accounting messages are sent to the RADIUS server regarding device access (see Table 13). dataUsage – accounting messages are sent to the RADIUS server regarding data usage (see Table 13).
PMP 450 Operations Guide Configuring a RADIUS server Table 12 SM User Authentication and Access Tracking attributes Attribute Meaning • Local: The local SM is checked for accounts. No centralized RADIUS accounting (access control) is performed. • Remote: Authentication by the centralized RADIUS server is required to gain access to the SM if the SM is registered to an AP that has RADIUS AAA Authentication Mode selected.
Configuring a RADIUS server PMP 450 Operations Guide Table 13 Device data accounting RADIUS attributes Sender Message Attribute Value AP AccountingRequest Acct-Status-Type 1 - Start Acct-Session-Id Unique per AP session. Initial value is SM MAC, and increments after every start message sent of an in session SM. Event-Timestamp UTC time the event occurred on the AP Acct-Status-Type 2 - Stop Acct-Session-Id Unique per AP session.
PMP 450 Operations Guide Sender AP Message AccountingRequest pmp-0049 (September 2012) Configuring a RADIUS server Attribute Value Acct-Input-Packets Sum of unicast and multicast packets that are sent to a particular SM over the regular data VC and the high priority data VC (if enabled). It will not include broadcast. Acct-Output-Packets Sum of unicast and multicast packets that are sent from a particular SM over the regular data VC and the high priority data VC (if enabled).
Configuring a RADIUS server Sender Message PMP 450 Operations Guide Attribute Value Description Acct-OutputGigawords Number of times the AcctOutput-Octets counter has wrapped around 2^32 over the course of the session Acct-Session-Time Uptime of the SM session. Acct-Input-Packets Sum of unicast and multicast packets that are sent to a particular SM over the regular data VC and the high priority data VC (if enabled). It will not include broadcast.
PMP 450 Operations Guide Configuring a RADIUS server If an operator clears the VC statistics on the device through the management GUI, a RADIUS stop message and data start message will be issued for each device affected. The start and stop messages will only be sent once every 5 minutes, so if an operator clears these statistics multiple times within 5 minutes, only one set of data stop/start messages will be sent. This may result in inaccurate data accumulation results.
Configuring a RADIUS server PMP 450 Operations Guide The Canopy system is configured for AAA authentication The SM is not configured for DHCP on its management interface. If DHCP is enabled and these attributes are configured in the RADIUS server, the attributes will be ignored by the SM. The SM management interface must be configured to be publically accessible.
PMP 450 Operations Guide RADIUS Attribute Framed-IP-Address Chapter 3: Managing the network from a Network Management Station (NMS) SNMPv2 (Simple Network Management Protocol Version 2) can be used to manage and monitor the modules under SMI (Structure of Management Information) specifications. SMI specifies management information definitions in ASN.1 (Abstract Syntax Notation One) language. SNMPv2 supports both 32-bit and 64-bit counters. The SMI for SNMPv2 is defined in RFC 1902 at http://www.faqs.
Simple Network Management Protocol (SNMP) Commands Managing the network from a Network Management Station (NMS) Roles of Hardware and Software Elements Role of the Agent In SNMP, software on each managed device acts as the agent. The agent collects and stores management information in ASN.1 format, in a structure that a MIB (management information base) defines. The agent responds to commands to send information about the managed device. modify specific data on the managed device.
PMP 450 Operations Guide AP SNMP Proxy to SMs traversal operations, which the manager uses to identify supported objects and to format information about those objects into relational tables. In a typical network, the manager issues these commands to the agents of more than one module (to all SMs in the operator network, for example). Traps from the Agent When a specified event occurs in the module, the agent initiates a trap, for which the agent sends an unsolicited asynchronous message to the manager.
Cascading Path to the MIB Managing the network from a Network Management Station (NMS) Management Information Base (MIB) The MIB, the SNMP-defined data structure, is a tree of standard branches that lead to optional, non-standard positions in the data hierarchy. The MIB contains both objects that SNMP is allowed to control (bandwidth allocation or access, for example) objects that SNMP is allowed to monitor (packet transfer, bit rate, and error data, for example).
PMP 450 Operations Guide Canopy Enterprise MIB Thus, the path to an object that is managed under MIB-II begins with the decimal string 1.3.6.1.2.1 and ends with the object identifier and instance(s), and the path to an object that is managed under the Cambium Enterprise MIB begins with 1.3.6.1.4.1, and ends with the object identifier and instance(s). Object Instances An object in the MIB can have either only a single instance or multiple instances, as follows: a scalar object has only a single instance.
SM MIB Objects Managing the network from a Network Management Station (NMS) To use this MIB with an NMS, perform the following steps. Procedure 2 Using the MIB with an NMS 1 On the NMS, immediately beneath the root directory, create directory mibviewer. 2 Immediately beneath the mibviewer directory, create directory cambiummibs. 3 Download the following three standard MIB files from the Internet Engineering Task Force at http://www.simpleweb.
PMP 450 Operations Guide SM MIB Objects authKeySm.0 .1.3.6.1.4.1.161.19.3.2.1.7.0 OctetString enable8023link.0 .1.3.6.1.4.1.161.19.3.2.1.8.0 Integer authKeyOption.0 .1.3.6.1.4.1.161.19.3.2.1.9.0 Integer timingPulseGated.0 .1.3.6.1.4.1.161.19.3.2.1.10.0 Integer naptPrivateIP.0 .1.3.6.1.4.1.161.19.3.2.1.11.0 IpAddress naptPrivateSubnetMask.0 .1.3.6.1.4.1.161.19.3.2.1.12.0 IpAddress naptPublicIP.0 .1.3.6.1.4.1.161.19.3.2.1.13.0 IpAddress naptPublicSubnetMask.0 .1.3.6.1.4.1.161.19.3.2.1.
SM MIB Objects 3-8 Managing the network from a Network Management Station (NMS) dwnLnkLimit.0 .1.3.6.1.4.1.161.19.3.2.1.65.0 Integer ipAccessFilterEnable.0 .1.3.6.1.4.1.161.19.3.2.1.68.0 Integer allowedIPAccess1.0 .1.3.6.1.4.1.161.19.3.2.1.69.0 IpAddress allowedIPAccess2.0 .1.3.6.1.4.1.161.19.3.2.1.70.0 IpAddress allowedIPAccess3.0 .1.3.6.1.4.1.161.19.3.2.1.71.0 IpAddress rfDhcpState.0 .1.3.6.1.4.1.161.19.3.2.1.72.0 Integer bCastMIR.0 .1.3.6.1.4.1.161.19.3.2.1.73.
PMP 450 Operations Guide SM MIB Objects colorCode3.0 .1.3.6.1.4.1.161.19.3.2.1.99.0 Integer colorCodepriority3.0 .1.3.6.1.4.1.161.19.3.2.1.100.0 Integer colorCode4.0 .1.3.6.1.4.1.161.19.3.2.1.101.0 Integer colorCodepriority4.0 .1.3.6.1.4.1.161.19.3.2.1.102.0 Integer colorCode5.0 .1.3.6.1.4.1.161.19.3.2.1.103.0 Integer colorCodepriority5.0 .1.3.6.1.4.1.161.19.3.2.1.104.0 Integer colorCode6.0 .1.3.6.1.4.1.161.19.3.2.1.105.0 Integer colorCodepriority6.0 .1.3.6.1.4.1.161.19.3.2.1.106.
SM MIB Objects Managing the network from a Network Management Station (NMS) dhcpcdns2.0 .1.3.6.1.4.1.161.19.3.2.2.16.0 IpAddress dhcpcdns3.0 .1.3.6.1.4.1.161.19.3.2.2.17.0 IpAddress dhcpDomName.0 .1.3.6.1.4.1.161.19.3.2.2.18.0 OctetString adaptRate.0 .1.3.6.1.4.1.161.19.3.2.2.20.0 OctetString radioDbmInt.0 .1.3.6.1.4.1.161.19.3.2.2.21.0 Integer radioTxPwr.0 .1.3.6.1.4.1.161.19.3.2.2.23.0 OctetString activeRegion.0 .1.3.6.1.4.1.161.19.3.2.2.24.0 OctetString snmpBerLevel.0 .1.3.6.1.4.
PMP 450 Operations Guide SM MIB Objects pppoeSessIdleTime.0 .1.3.6.1.4.1.161.19.3.2.2.60.0 TimeTicks radioDbmAvg.0 .1.3.6.1.4.1.161.19.3.2.2.61.0 Integer zoltarFPGAFreqOffset.0 .1.3.6.1.4.1.161.19.3.2.2.62.0 Integer zoltarSWFreqOffset.0 .1.3.6.1.4.1.161.19.3.2.2.63.0 Integer airDelayns.0 .1.3.6.1.4.1.161.19.3.2.2.64.0 Gauge currentColorCode.0 .1.3.6.1.4.1.161.19.3.2.2.65.0 Integer currentColorCodePri.0 .1.3.6.1.4.1.161.19.3.2.2.66.0 Integer currentChanFreq.0 .1.3.6.1.4.1.161.19.3.2.
SM MIB Objects Managing the network from a Network Management Station (NMS) protocol.8 .1.3.6.1.4.1.161.19.3.2.5.1.2.8 Integer protocol.9 .1.3.6.1.4.1.161.19.3.2.5.1.2.9 Integer protocol.10 .1.3.6.1.4.1.161.19.3.2.5.1.2.10 Integer port.1 .1.3.6.1.4.1.161.19.3.2.5.1.3.1 Integer port.2 .1.3.6.1.4.1.161.19.3.2.5.1.3.2 Integer port.3 .1.3.6.1.4.1.161.19.3.2.5.1.3.3 Integer port.4 .1.3.6.1.4.1.161.19.3.2.5.1.3.4 Integer port.5 .1.3.6.1.4.1.161.19.3.2.5.1.3.5 Integer port.6 .1.3.6.1.4.
PMP 450 Operations Guide SM MIB Objects certificateDN.1 .1.3.6.1.4.1.161.19.3.2.7.1.1.4.1 OctetString certificateDN.2 .1.3.6.1.4.1.161.19.3.2.7.1.1.4.2 OctetString numAuthCerts.0 .1.3.6.1.4.1.161.19.3.2.7.2.0 Integer authenticationEnforce.0 .1.3.6.1.4.1.161.19.3.2.7.3.0 Integer phase1.0 .1.3.6.1.4.1.161.19.3.2.7.4.0 Integer phase2.0 .1.3.6.1.4.1.161.19.3.2.7.5.0 Integer authOuterId.0 .1.3.6.1.4.1.161.19.3.2.7.6.0 OctetString authPassword.0 .1.3.6.1.4.1.161.19.3.2.7.7.
SM MIB Objects Managing the network from a Network Management Station (NMS) inSyncCount.0 .1.3.6.1.4.1.161.19.3.3.1.21.0 Integer outSyncCount.0 .1.3.6.1.4.1.161.19.3.3.1.22.0 Integer pllOutLockCount.0 .1.3.6.1.4.1.161.19.3.3.1.23.0 Integer txCalFailure.0 .1.3.6.1.4.1.161.19.3.3.1.24.0 Integer swVersion.0 .1.3.6.1.4.1.161.19.3.3.1.25.0 OctetString pldVersion.0 .1.3.6.1.4.1.161.19.3.3.1.26.0 OctetString platformInfo.0 .1.3.6.1.4.1.161.19.3.3.1.27.0 OctetString packetOverloadCounter.0 .
PMP 450 Operations Guide SM MIB Objects bridgeCbRFStatutosscap.0 .1.3.6.1.4.1.161.19.3.3.1.52.0 Counter32 bridgeCbErrStatNI1QSend.0 .1.3.6.1.4.1.161.19.3.3.1.53.0 Counter32 bridgeCbErrStatNI2QSend.0 .1.3.6.1.4.1.161.19.3.3.1.54.0 Counter32 bridgeCbErrStatBridgeFull.0 .1.3.6.1.4.1.161.19.3.3.1.55.0 Counter32 bridgeCbErrStatSendMsg.0 .1.3.6.1.4.1.161.19.3.3.1.56.0 Counter32 bridgeCbErrStatAPFecQSend.0 .1.3.6.1.4.1.161.19.3.3.1.57.0 Counter32 bridgeCbErrStatApRfQSend.0 .1.3.6.1.4.1.161.19.
SM MIB Objects Managing the network from a Network Management Station (NMS) rfStatRcvLTStart.0 .1.3.6.1.4.1.161.19.3.3.1.82.0 Counter32 rfStatRcvLTStartHS.0 .1.3.6.1.4.1.161.19.3.3.1.83.0 Counter32 rfStatRcvLTResult.0 .1.3.6.1.4.1.161.19.3.3.1.84.0 Counter32 rfStatXmtLTResult.0 .1.3.6.1.4.1.161.19.3.3.1.85.0 Counter32 whispFeatureKeyOrigin.0 .1.3.6.1.4.1.161.19.3.3.1.86.0 OctetString radioMSN.0 .1.3.6.1.4.1.161.19.3.3.1.87.0 OctetString updateStatus.0 .1.3.6.1.4.1.161.19.3.3.1.88.
PMP 450 Operations Guide SM MIB Objects pass2Status.0 .1.3.6.1.4.1.161.19.3.3.2.7.0 OctetString bridgeEntryTimeout.0 .1.3.6.1.4.1.161.19.3.3.2.8.0 Integer snmpMibPerm.0 .1.3.6.1.4.1.161.19.3.3.2.9.0 Integer antennaGain.0 .1.3.6.1.4.1.161.19.3.3.2.14.0 Integer dynamicLearning.0 .1.3.6.1.4.1.161.19.3.3.2.16.0 Integer managementVID.0 .1.3.6.1.4.1.161.19.3.3.2.17.0 Integer agingTimeout.0 .1.3.6.1.4.1.161.19.3.3.2.18.0 Integer frameType.0 .1.3.6.1.4.1.161.19.3.3.2.19.
SM MIB Objects Managing the network from a Network Management Station (NMS) mngtIP5.0 .1.3.6.1.4.1.161.19.3.3.2.63.0 IpAddress subnetMask5.0 .1.3.6.1.4.1.161.19.3.3.2.64.0 Integer mngtIP6.0 .1.3.6.1.4.1.161.19.3.3.2.65.0 IpAddress subnetMask6.0 .1.3.6.1.4.1.161.19.3.3.2.66.0 Integer mngtIP7.0 .1.3.6.1.4.1.161.19.3.3.2.67.0 IpAddress subnetMask7.0 .1.3.6.1.4.1.161.19.3.3.2.68.0 Integer mngtIP8.0 .1.3.6.1.4.1.161.19.3.3.2.69.0 IpAddress subnetMask8.0 .1.3.6.1.4.1.161.19.3.3.2.70.
PMP 450 Operations Guide SM MIB Objects mac2VIDMapVid.0 .1.3.6.1.4.1.161.19.3.3.2.99.0 Integer mac3VIDMapAddr.0 .1.3.6.1.4.1.161.19.3.3.2.100.0 OctetString mac3VIDMapVid.0 .1.3.6.1.4.1.161.19.3.3.2.101.0 Integer mac4VIDMapAddr.0 .1.3.6.1.4.1.161.19.3.3.2.102.0 OctetString mac4VIDMapVid.0 .1.3.6.1.4.1.161.19.3.3.2.103.0 Integer mac5VIDMapAddr.0 .1.3.6.1.4.1.161.19.3.3.2.104.0 OctetString mac5VIDMapVid.0 .1.3.6.1.4.1.161.19.3.3.2.105.0 Integer mac6VIDMapAddr.0 .1.3.6.1.4.1.161.19.3.3.
SM MIB Objects Managing the network from a Network Management Station (NMS) userP3Filter.0 .1.3.6.1.4.1.161.19.3.2.1.38.0 Integer allOtherIpFilter.0 .1.3.6.1.4.1.161.19.3.2.1.39.0 Integer allIpv4Filter.0 .1.3.6.1.4.1.161.19.3.2.1.116.0 Integer arpFilter.0 .1.3.6.1.4.1.161.19.3.2.1.41.0 Integer allOthersFilter.0 .1.3.6.1.4.1.161.19.3.2.1.42.0 Integer userDefinedPort1.0 .1.3.6.1.4.1.161.19.3.2.1.43.0 Integer port1TCPFilter.0 .1.3.6.1.4.1.161.19.3.2.1.44.0 Integer port1UDPFilter.0 .1.3.
PMP 450 Operations Guide SM MIB Objects reboot.0 .1.3.6.1.4.1.161.19.3.3.3.2.0 Integer clearEventLog.0 .1.3.6.1.4.1.161.19.3.3.3.3.0 Integer rebootIfRequired.0 .1.3.6.1.4.1.161.19.3.3.3.4.0 Integer clearBERStats.0 .1.3.6.1.4.1.161.19.3.3.3.5.0 Integer updateDevice.0 .1.3.6.1.4.1.161.19.3.3.3.6.0 Integer whispBridgeMacAddr.1 .1.3.6.1.4.1.161.19.3.3.4.1.1.1 OctetString whispBridgeMacAddr.2 .1.3.6.1.4.1.161.19.3.3.4.1.1.2 OctetString whispBridgeDesLuid.1 .1.3.6.1.4.1.161.19.3.3.4.1.2.
SM MIB Objects Managing the network from a Network Management Station (NMS) codePoint11.0 .1.3.6.1.4.1.161.19.3.3.9.12.0 Integer codePoint12.0 .1.3.6.1.4.1.161.19.3.3.9.13.0 Integer codePoint13.0 .1.3.6.1.4.1.161.19.3.3.9.14.0 Integer codePoint14.0 .1.3.6.1.4.1.161.19.3.3.9.15.0 Integer codePoint15.0 .1.3.6.1.4.1.161.19.3.3.9.16.0 Integer codePoint16.0 .1.3.6.1.4.1.161.19.3.3.9.17.0 Integer codePoint17.0 .1.3.6.1.4.1.161.19.3.3.9.18.0 Integer codePoint18.0 .1.3.6.1.4.1.161.19.3.3.9.
PMP 450 Operations Guide SM MIB Objects codePoint40.0 .1.3.6.1.4.1.161.19.3.3.9.41.0 Integer codePoint41.0 .1.3.6.1.4.1.161.19.3.3.9.42.0 Integer codePoint42.0 .1.3.6.1.4.1.161.19.3.3.9.43.0 Integer codePoint43.0 .1.3.6.1.4.1.161.19.3.3.9.44.0 Integer codePoint44.0 .1.3.6.1.4.1.161.19.3.3.9.45.0 Integer codePoint45.0 .1.3.6.1.4.1.161.19.3.3.9.46.0 Integer codePoint46.0 .1.3.6.1.4.1.161.19.3.3.9.47.0 Integer codePoint47.0 .1.3.6.1.4.1.161.19.3.3.9.48.0 Integer codePoint48.0 .1.3.6.
SM MIB Objects Managing the network from a Network Management Station (NMS) userLoginName.3 .1.3.6.1.4.1.161.19.3.3.10.1.2.3 OctetString userLoginName.4 .1.3.6.1.4.1.161.19.3.3.10.1.2.4 OctetString userPswd.1 .1.3.6.1.4.1.161.19.3.3.10.1.3.1 OctetString userPswd.2 .1.3.6.1.4.1.161.19.3.3.10.1.3.2 OctetString userPswd.3 .1.3.6.1.4.1.161.19.3.3.10.1.3.3 OctetString userPswd.4 .1.3.6.1.4.1.161.19.3.3.10.1.3.4 OctetString accessLevel.1 .1.3.6.1.4.1.161.19.3.3.10.1.4.1 Integer accessLevel.
PMP 450 Operations Guide SM MIB Objects neighborMAC.8 .1.3.6.1.4.1.161.19.3.3.11.1.2.8 OctetString neighborMAC.9 .1.3.6.1.4.1.161.19.3.3.11.1.2.9 OctetString neighborMAC.10 .1.3.6.1.4.1.161.19.3.3.11.1.2.10 OctetString neighborMAC.11 .1.3.6.1.4.1.161.19.3.3.11.1.2.11 OctetString neighborMAC.12 .1.3.6.1.4.1.161.19.3.3.11.1.2.12 OctetString neighborMAC.13 .1.3.6.1.4.1.161.19.3.3.11.1.2.13 OctetString neighborMAC.14 .1.3.6.1.4.1.161.19.3.3.11.1.2.14 OctetString neighborMAC.15 .1.3.6.1.
SM MIB Objects Managing the network from a Network Management Station (NMS) neighborIP.18 .1.3.6.1.4.1.161.19.3.3.11.1.3.18 OctetString neighborIP.19 .1.3.6.1.4.1.161.19.3.3.11.1.3.19 OctetString neighborIP.20 .1.3.6.1.4.1.161.19.3.3.11.1.3.20 OctetString neighborSiteName.1 .1.3.6.1.4.1.161.19.3.3.11.1.4.1 OctetString neighborSiteName.2 .1.3.6.1.4.1.161.19.3.3.11.1.4.2 OctetString neighborSiteName.3 .1.3.6.1.4.1.161.19.3.3.11.1.4.3 OctetString neighborSiteName.4 .1.3.6.1.4.1.161.19.3.3.
PMP 450 Operations Guide SM MIB Objects trap2.0 .1.3.6.1.4.1.161.19.3.3.13.7.0 OctetString trap3.0 .1.3.6.1.4.1.161.19.3.3.13.8.0 OctetString trap4.0 .1.3.6.1.4.1.161.19.3.3.13.9.0 OctetString trap5.0 .1.3.6.1.4.1.161.19.3.3.13.10.0 OctetString trap6.0 .1.3.6.1.4.1.161.19.3.3.13.11.0 OctetString trap7.0 .1.3.6.1.4.1.161.19.3.3.13.12.0 OctetString trap8.0 .1.3.6.1.4.1.161.19.3.3.13.13.0 OctetString trap9.0 .1.3.6.1.4.1.161.19.3.3.13.14.0 OctetString trap10.0 .1.3.6.1.4.1.161.19.3.
SM MIB Objects Managing the network from a Network Management Station (NMS) frequency.1.5565000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5565000 Integer frequency.1.5570000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5570000 Integer frequency.1.5575000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5575000 Integer frequency.1.5580000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5580000 Integer frequency.1.5585000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5585000 Integer frequency.1.5590000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.
PMP 450 Operations Guide AP MIB Objects frequency.1.5735000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5735000 Integer frequency.1.5740000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5740000 Integer frequency.1.5745000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5745000 Integer frequency.1.5750000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5750000 Integer frequency.1.5755000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5755000 Integer frequency.1.5760000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5760000 Integer frequency.1.5765000 .1.3.
AP MIB Objects Managing the network from a Network Management Station (NMS) upLnkDataRate.0 .1.3.6.1.4.1.161.19.3.2.1.62.0 Integer upLnkLimit.0 .1.3.6.1.4.1.161.19.3.2.1.63.0 Integer dwnLnkDataRate.0 .1.3.6.1.4.1.161.19.3.2.1.64.0 Integer dwnLnkLimit.0 .1.3.6.1.4.1.161.19.3.2.1.65.0 Integer maxRange.0 .1.3.6.1.4.1.161.19.3.1.1.17.0 Integer lanIpAp.0 .1.3.6.1.4.1.161.19.3.1.1.23.0 IpAddress lanMaskAp.0 .1.3.6.1.4.1.161.19.3.1.1.24.0 IpAddress defaultGwAp.0 .1.3.6.1.4.1.161.19.3.1.1.
PMP 450 Operations Guide AP MIB Objects remoteSpectrumAnalyzerLUID.0 .1.3.6.1.4.1.161.19.3.1.1.57.0 Integer dlnkBcastCIR.0 .1.3.6.1.4.1.161.19.3.1.1.59.0 Integer verifyGPSChecksum.0 .1.3.6.1.4.1.161.19.3.1.1.60.0 Integer apVlanOverride.0 .1.3.6.1.4.1.161.19.3.1.1.61.0 Integer dhcpRelayAgentEnable.0 .1.3.6.1.4.1.161.19.3.1.1.62.0 Integer colorCodeRescanTimer.0 .1.3.6.1.4.1.161.19.3.1.1.64.0 Integer colorCodeRescanIdleTimer.0 .1.3.6.1.4.1.161.19.3.1.1.65.0 Integer authKeyOptionAP.0 .1.
AP MIB Objects Managing the network from a Network Management Station (NMS) syslogServerPort.0 .1.3.6.1.4.1.161.19.3.1.1.103.0 Integer syslogXmitAP.0 .1.3.6.1.4.1.161.19.3.1.1.104.0 Integer syslogXmitSMs.0 .1.3.6.1.4.1.161.19.3.1.1.105.0 Integer accountingInterimUpdateInterval.0 .1.3.6.1.4.1.161.19.3.1.1.106.0 Integer radioMode.0 .1.3.6.1.4.1.161.19.3.1.1.206.0 Integer rfTelnetAccess.0 .1.3.6.1.4.1.161.19.3.1.1.207.0 Integer linkTestLUID.0 .1.3.6.1.4.1.161.19.3.1.2.1.1.
PMP 450 Operations Guide AP MIB Objects signalToNoiseRatioUpLink.0 .1.3.6.1.4.1.161.19.3.1.2.2.34.0 Integer whispGPSStats.0 .1.3.6.1.4.1.161.19.3.1.3.1.0 Integer gpsSyncSource.0 .1.3.6.1.4.1.161.19.3.1.3.2.0 OctetString gpsSyncStatus.0 .1.3.6.1.4.1.161.19.3.1.3.3.0 OctetString gpsTrackingMode.0 .1.3.6.1.4.1.161.19.3.1.3.4.0 OctetString gpsTime.0 .1.3.6.1.4.1.161.19.3.1.3.5.0 OctetString gpsDate.0 .1.3.6.1.4.1.161.19.3.1.3.6.0 OctetString gpsSatellitesTracked.0 .1.3.6.1.4.1.161.19.3.
AP MIB Objects Managing the network from a Network Management Station (NMS) linkOutDiscards.2 .1.3.6.1.4.1.161.19.3.1.4.1.16.2 Counter32 linkOutError.2 .1.3.6.1.4.1.161.19.3.1.4.1.17.2 Counter32 linkOutQLen.2 .1.3.6.1.4.1.161.19.3.1.4.1.18.2 Gauge linkSessState.2 .1.3.6.1.4.1.161.19.3.1.4.1.19.2 Integer linkESN.2 .1.3.6.1.4.1.161.19.3.1.4.1.20.2 OctetString linkAirDelay.2 .1.3.6.1.4.1.161.19.3.1.4.1.24.2 Integer linkRegCount.2 .1.3.6.1.4.1.161.19.3.1.4.1.25.2 Integer linkReRegCount.
PMP 450 Operations Guide AP MIB Objects dataVCNumHiQ.2 .1.3.6.1.4.1.161.19.3.1.4.1.50.2 Integer linkInOctetsHiQ.2 .1.3.6.1.4.1.161.19.3.1.4.1.51.2 Counter32 linkInUcastPktsHiQ.2 .1.3.6.1.4.1.161.19.3.1.4.1.52.2 Counter32 linkInNUcastPktsHiQ.2 .1.3.6.1.4.1.161.19.3.1.4.1.53.2 Counter32 linkInDiscardsHiQ.2 .1.3.6.1.4.1.161.19.3.1.4.1.54.2 Counter32 linkInErrorHiQ.2 .1.3.6.1.4.1.161.19.3.1.4.1.55.2 Counter32 linkInUnknownProtosHiQ.2 .1.3.6.1.4.1.161.19.3.1.4.1.56.
AP MIB Objects Managing the network from a Network Management Station (NMS) lastNTPTime.0 .1.3.6.1.4.1.161.19.3.1.7.20.0 OctetString regulatoryStatus.0 .1.3.6.1.4.1.161.19.3.1.7.21.0 OctetString dhcpRlyAgntStat-reqRecvd.0 .1.3.6.1.4.1.161.19.3.1.7.22.0 Counter32 dhcpRlyAgntStat-reqRelayed.0 .1.3.6.1.4.1.161.19.3.1.7.23.0 Counter32 dhcpRlyAgntStat-reqDiscards.0 .1.3.6.1.4.1.161.19.3.1.7.24.0 Counter32 dhcpRlyAgntStat-respRecvd.0 .1.3.6.1.4.1.161.19.3.1.7.25.
PMP 450 Operations Guide AP MIB Objects radioFreqCarrier.1 .1.3.6.1.4.1.161.19.3.1.10.1.1.1.1 Integer radioDownlinkPercent.1 .1.3.6.1.4.1.161.19.3.1.10.1.1.2.1 Integer radioMaxRange.1 .1.3.6.1.4.1.161.19.3.1.10.1.1.3.1 Integer radioControlSlots.1 .1.3.6.1.4.1.161.19.3.1.10.1.1.4.1 Integer radioTransmitOutputPower.1 .1.3.6.1.4.1.161.19.3.1.10.1.1.5.1 Integer radioColorCode.1 .1.3.6.1.4.1.161.19.3.1.10.1.1.6.1 Integer protocol.1 .1.3.6.1.4.1.161.19.3.2.5.1.2.1 Integer protocol.2 .1.3.
AP MIB Objects Managing the network from a Network Management Station (NMS) localIp.6 .1.3.6.1.4.1.161.19.3.2.5.1.4.6 IpAddress localIp.7 .1.3.6.1.4.1.161.19.3.2.5.1.4.7 IpAddress localIp.8 .1.3.6.1.4.1.161.19.3.2.5.1.4.8 IpAddress localIp.9 .1.3.6.1.4.1.161.19.3.2.5.1.4.9 IpAddress localIp.10 .1.3.6.1.4.1.161.19.3.2.5.1.4.10 IpAddress whispBoxSoftwareVer.0 .1.3.6.1.4.1.161.19.3.3.1.1.0 OctetString whispBoxFPGAVer.0 .1.3.6.1.4.1.161.19.3.3.1.2.0 OctetString whispBoxEsn.0 .1.3.6.1.4.
PMP 450 Operations Guide AP MIB Objects platformInfo.0 .1.3.6.1.4.1.161.19.3.3.1.27.0 OctetString packetOverloadCounter.0 .1.3.6.1.4.1.161.19.3.3.1.29.0 Counter32 whispBoxP11Personality.0 .1.3.6.1.4.1.161.19.3.3.1.30.0 OctetString whispBoxP11FPGAType.0 .1.3.6.1.4.1.161.19.3.3.1.31.0 OctetString whispBoxP11BstrapFPGAVer.0 .1.3.6.1.4.1.161.19.3.3.1.32.0 OctetString rxOverrunPkts.0 .1.3.6.1.4.1.161.19.3.3.1.34.0 Counter32 boxTemperatureC.0 .1.3.6.1.4.1.161.19.3.3.1.35.
AP MIB Objects Managing the network from a Network Management Station (NMS) rfStatXmtBDataCnt.0 .1.3.6.1.4.1.161.19.3.3.1.60.0 Counter32 rfStatRcvUDataCnt.0 .1.3.6.1.4.1.161.19.3.3.1.61.0 Counter32 rfStatRcvBDataCnt.0 .1.3.6.1.4.1.161.19.3.3.1.62.0 Counter32 rfStatXmtCntlCnt.0 .1.3.6.1.4.1.161.19.3.3.1.63.0 Counter32 rfStatRcvCntlCnt.0 .1.3.6.1.4.1.161.19.3.3.1.64.0 Counter32 rfStatInSyncCount.0 .1.3.6.1.4.1.161.19.3.3.1.65.0 Counter32 rfStatOutSyncCount.0 .1.3.6.1.4.1.161.19.3.3.1.66.
PMP 450 Operations Guide AP MIB Objects syslogStatDropped.0 .1.3.6.1.4.1.161.19.3.3.1.90.0 Integer fecStatLinkLost.0 .1.3.6.1.4.1.161.19.3.3.1.91.0 Counter32 fecStatLinkDetected.0 .1.3.6.1.4.1.161.19.3.3.1.92.0 Counter32 natDhcpStatus.0 .1.3.6.1.4.1.161.19.3.3.1.93.0 OctetString fecInDiscardsCount.0 .1.3.6.1.4.1.161.19.3.3.1.94.0 Gauge fecInErrorsCount.0 .1.3.6.1.4.1.161.19.3.3.1.95.0 Gauge fecOutDiscardsCount.0 .1.3.6.1.4.1.161.19.3.3.1.96.0 Gauge fecOutErrorsCount.0 .1.3.6.1.4.1.
AP MIB Objects Managing the network from a Network Management Station (NMS) scheduling.0 .1.3.6.1.4.1.161.19.3.3.2.22.0 Integer transmitterOP.0 .1.3.6.1.4.1.161.19.3.3.2.23.0 Integer commStringRWrite.0 .1.3.6.1.4.1.161.19.3.3.2.36.0 OctetString subnetMask.0 .1.3.6.1.4.1.161.19.3.3.2.37.0 Integer mngtIP.0 .1.3.6.1.4.1.161.19.3.3.2.38.0 IpAddress allowVIDAccess.0 .1.3.6.1.4.1.161.19.3.3.2.39.0 Integer setDefaultPlug.0 .1.3.6.1.4.1.161.19.3.3.2.40.0 Integer gpsInput.0 .1.3.6.1.4.1.161.
PMP 450 Operations Guide AP MIB Objects mngtIP9.0 .1.3.6.1.4.1.161.19.3.3.2.71.0 IpAddress subnetMask9.0 .1.3.6.1.4.1.161.19.3.3.2.72.0 Integer mngtIP10.0 .1.3.6.1.4.1.161.19.3.3.2.73.0 IpAddress subnetMask10.0 .1.3.6.1.4.1.161.19.3.3.2.74.0 Integer lldpBroadcastEnable.0 .1.3.6.1.4.1.161.19.3.3.2.76.0 Integer regionCode.0 .1.3.6.1.4.1.161.19.3.3.2.77.0 Integer commStringROnly.0 .1.3.6.1.4.1.161.19.3.3.2.79.0 OctetString ethernetLinkSpeed.0 .1.3.6.1.4.1.161.19.3.3.2.80.
AP MIB Objects Managing the network from a Network Management Station (NMS) arpFilter.0 .1.3.6.1.4.1.161.19.3.2.1.41.0 Integer allOthersFilter.0 .1.3.6.1.4.1.161.19.3.2.1.42.0 Integer userDefinedPort1.0 .1.3.6.1.4.1.161.19.3.2.1.43.0 Integer port1TCPFilter.0 .1.3.6.1.4.1.161.19.3.2.1.44.0 Integer port1UDPFilter.0 .1.3.6.1.4.1.161.19.3.2.1.45.0 Integer userDefinedPort2.0 .1.3.6.1.4.1.161.19.3.2.1.46.0 Integer port2TCPFilter.0 .1.3.6.1.4.1.161.19.3.2.1.47.0 Integer port2UDPFilter.0 .1.
PMP 450 Operations Guide AP MIB Objects updateDevice.0 .1.3.6.1.4.1.161.19.3.3.3.6.0 Integer whispBridgeMacAddr.1 .1.3.6.1.4.1.161.19.3.3.4.1.1.1 OctetString whispBridgeMacAddr.2 .1.3.6.1.4.1.161.19.3.3.4.1.1.2 OctetString whispBridgeMacAddr.3 .1.3.6.1.4.1.161.19.3.3.4.1.1.3 OctetString whispBridgeDesLuid.1 .1.3.6.1.4.1.161.19.3.3.4.1.2.1 Integer whispBridgeDesLuid.2 .1.3.6.1.4.1.161.19.3.3.4.1.2.2 Integer whispBridgeDesLuid.3 .1.3.6.1.4.1.161.19.3.3.4.1.2.3 Integer whispBridgeAge.
AP MIB Objects Managing the network from a Network Management Station (NMS) codePoint11.0 .1.3.6.1.4.1.161.19.3.3.9.12.0 Integer codePoint12.0 .1.3.6.1.4.1.161.19.3.3.9.13.0 Integer codePoint13.0 .1.3.6.1.4.1.161.19.3.3.9.14.0 Integer codePoint14.0 .1.3.6.1.4.1.161.19.3.3.9.15.0 Integer codePoint15.0 .1.3.6.1.4.1.161.19.3.3.9.16.0 Integer codePoint16.0 .1.3.6.1.4.1.161.19.3.3.9.17.0 Integer codePoint17.0 .1.3.6.1.4.1.161.19.3.3.9.18.0 Integer codePoint18.0 .1.3.6.1.4.1.161.19.3.3.9.
PMP 450 Operations Guide AP MIB Objects codePoint41.0 .1.3.6.1.4.1.161.19.3.3.9.42.0 Integer codePoint42.0 .1.3.6.1.4.1.161.19.3.3.9.43.0 Integer codePoint43.0 .1.3.6.1.4.1.161.19.3.3.9.44.0 Integer codePoint44.0 .1.3.6.1.4.1.161.19.3.3.9.45.0 Integer codePoint45.0 .1.3.6.1.4.1.161.19.3.3.9.46.0 Integer codePoint46.0 .1.3.6.1.4.1.161.19.3.3.9.47.0 Integer codePoint47.0 .1.3.6.1.4.1.161.19.3.3.9.48.0 Integer codePoint48.0 .1.3.6.1.4.1.161.19.3.3.9.49.0 Integer codePoint49.0 .1.3.6.
AP MIB Objects Managing the network from a Network Management Station (NMS) userPswd.1 .1.3.6.1.4.1.161.19.3.3.10.1.3.1 OctetString userPswd.2 .1.3.6.1.4.1.161.19.3.3.10.1.3.2 OctetString userPswd.3 .1.3.6.1.4.1.161.19.3.3.10.1.3.3 OctetString userPswd.4 .1.3.6.1.4.1.161.19.3.3.10.1.3.4 OctetString accessLevel.1 .1.3.6.1.4.1.161.19.3.3.10.1.4.1 Integer accessLevel.2 .1.3.6.1.4.1.161.19.3.3.10.1.4.2 Integer accessLevel.3 .1.3.6.1.4.1.161.19.3.3.10.1.4.3 Integer accessLevel.4 .1.3.6.1.
PMP 450 Operations Guide AP MIB Objects neighborMAC.11 .1.3.6.1.4.1.161.19.3.3.11.1.2.11 OctetString neighborMAC.12 .1.3.6.1.4.1.161.19.3.3.11.1.2.12 OctetString neighborMAC.13 .1.3.6.1.4.1.161.19.3.3.11.1.2.13 OctetString neighborMAC.14 .1.3.6.1.4.1.161.19.3.3.11.1.2.14 OctetString neighborMAC.15 .1.3.6.1.4.1.161.19.3.3.11.1.2.15 OctetString neighborMAC.16 .1.3.6.1.4.1.161.19.3.3.11.1.2.16 OctetString neighborMAC.17 .1.3.6.1.4.1.161.19.3.3.11.1.2.17 OctetString neighborMAC.18 .1.3.
AP MIB Objects Managing the network from a Network Management Station (NMS) neighborSiteName.2 .1.3.6.1.4.1.161.19.3.3.11.1.4.2 OctetString neighborSiteName.3 .1.3.6.1.4.1.161.19.3.3.11.1.4.3 OctetString neighborSiteName.4 .1.3.6.1.4.1.161.19.3.3.11.1.4.4 OctetString neighborSiteName.5 .1.3.6.1.4.1.161.19.3.3.11.1.4.5 OctetString neighborSiteName.6 .1.3.6.1.4.1.161.19.3.3.11.1.4.6 OctetString neighborSiteName.7 .1.3.6.1.4.1.161.19.3.3.11.1.4.7 OctetString neighborSiteName.8 .1.3.6.1.4.
PMP 450 Operations Guide AP MIB Objects trap7.0 .1.3.6.1.4.1.161.19.3.3.13.12.0 OctetString trap8.0 .1.3.6.1.4.1.161.19.3.3.13.13.0 OctetString trap9.0 .1.3.6.1.4.1.161.19.3.3.13.14.0 OctetString trap10.0 .1.3.6.1.4.1.161.19.3.3.13.15.0 OctetString radioIndex.1 .1.3.6.1.4.1.161.19.3.3.15.1.1.1.1 Integer radioType.1 .1.3.6.1.4.1.161.19.3.3.15.1.1.2.1 Integer radioPaths.1 .1.3.6.1.4.1.161.19.3.3.15.1.1.3.1 Integer pathIndex.1.1 .1.3.6.1.4.1.161.19.3.3.15.2.1.1.1.1 Integer pathIndex.
AP MIB Objects Managing the network from a Network Management Station (NMS) frequency.1.5660000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5660000 Integer frequency.1.5665000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5665000 Integer frequency.1.5670000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5670000 Integer frequency.1.5675000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5675000 Integer frequency.1.5680000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5680000 Integer frequency.1.5685000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.
PMP 450 Operations Guide AP MIB Objects frequency.1.5835000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.5835000 Integer frequency.1.5840000 .1.3.6.1.4.1.161.19.3.3.15.3.1.1.1.
Traps provided in the Cambium Enterprise MIB Managing the network from a Network Management Station (NMS) Configuring modules for SNMP access Cambium modules provide the following Configuration web page parameters in the SNMP tab. These govern SNMP access from the manager to the agent: Community String, which specifies the password for security between managers and the agent. Accessing Subnet, which specifies the subnet mask that allows managers to poll the agents.
PMP 450 Operations Guide MIB Viewers whispRadarDetected, which signals that the one-minute scan has been completed, radar has been detected, and the radio will shutdown. whispRadarEnd, which signals that the one-minute scan has been completed, radar has not been detected, and the radio will resume normal operation. MIB Viewers Any of several commercially available MIB viewers can facilitate management of these objects through SNMP. Some are available as open source software.
CNUT Functions Managing the network from a Network Management Station (NMS) Using the Canopy Network Updater Tool (CNUT) The Canopy Network Updater Tool (CNUT) manages and automates the software and firmware upgrade process for a Canopy radio, CMMmicro, or CMM4 (but not its 14-port switch) across the network. This eliminates the need for an administrator to visit each radio in the network (or each AP while using the Autoupdate feature) to upgrade the modules.
PMP 450 Operations Guide Script Engine Network Element Groups With the Canopy Network Updater Tool, you can identify element groups composed of network elements that you select. Identifying these element groups organizes the display of elements (for example, by region or by AP cluster). allows you to o perform an operation on all elements in the group simultaneously.
CNUT Download Managing the network from a Network Management Station (NMS) Software Dependencies for CNUT CNUT functionality requires one of the following operating systems o Windows® 2000 o Windows Server 2003 o Windows XP or XP Professional o Windows 7 o Red Hat Enterprise Linux (32-bit) Version 4 or 5 Java™ Runtime Version 2.0 or later (installed by the CNUT installation tool) CNUT Download CNUT can be downloaded together with each system release that supports CNUT.
PMP 450 Operations Guide Viewing General Status (AP) Chapter 4: Using Informational Tabs in the GUI Viewing General Status (AP) The General Status tab provides information on the operation of this AP. This is the tab that opens by default when you access the GUI of the AP. Examples of AP General Status tabs are displayed below.
Viewing General Status (AP) Using Informational Tabs in the GUI Figure 12 AP General Status page The General Status tab provides the following read-only fields. Table 19 AP General Status attributes 4-2 Attribute Meaning Device Type This field indicates the type of the module. Values include the frequency band of the AP, its module type, and its MAC address. Software Version This field indicates the system release, the time and date of the release.
PMP 450 Operations Guide Viewing General Status (AP) Attribute Meaning FPGA Version This field indicates the version of the field-programmable gate array (FPGA) on the module. If you request technical support, provide the value of this field. FPGA Type Where the type of logic as a subset of the logic version in the module as manufactured distinguishes its circuit board, this field is present to indicate that type. If you request technical support, provide the value of this field.
Viewing General Status (AP) Using Informational Tabs in the GUI Attribute Meaning Temperature The current operating temperature of the board Registered SM Count This field indicates how many SMs are registered to the AP GPS Sync Pulse Status This field indicates the status of synchronization as follows: Generating sync indicates that the module is set to generate the sync pulse.
PMP 450 Operations Guide Viewing General Status (SM) Attribute Meaning Site Name This field indicates the name of the physical module. You can assign or change this name in the SNMP tab of the AP Configuration page. This information is also set into the sysName SNMP MIB-II object and can be polled by an SNMP management server. Site Contact This field indicates contact information for the physical module. You can provide or change this information in the SNMP tab of the AP Configuration page.
Viewing General Status (SM) Using Informational Tabs in the GUI Figure 13 General Status page of the SM 4-6 pmp-0049 (September 2012)
PMP 450 Operations Guide Viewing General Status (SM) The General Status tab provides the following read-only fields. Table 20 SM General Status attributes Attribute Meaning Device Type This field indicates the type of the module. Values include the frequency band of the SM, its module type, and its MAC address. Software Version This field indicates the system release, the time and date of the release. If you request technical support, provide the information from this field.
Viewing General Status (SM) Using Informational Tabs in the GUI Attribute Meaning Registered AP This field displays the MAC address of the AP to which this SM is registered. Color Code Module parameter that identifies the other modules with which communication is allowed. The range of values is 0 to 255. When set at 0, the Color Code does not restrict communications with any other module. Channel Frequency This field lists the current operating frequency of the radio.
PMP 450 Operations Guide Viewing Session Status (AP) Attribute Meaning Region Code A parameter that offers multiple fixed selections, each of which automatically implements frequency band range restrictions for the selected region. Units shipped to regions other than the United States must be configured with the corresponding Region Code to comply with local regulatory requirements. Site Name This field indicates the name of the physical module.
Viewing Session Status (AP) Using Informational Tabs in the GUI Figure 14 Session Status tab data Table 21 AP Session Status attributes Attribute Meaning LUID This field displays the LUID (logical unit ID) of the SM. As each SM registers to the AP, the system assigns an LUID of 2 or a higher unique number to the SM. If an SM loses registration with the AP and then regains registration, the SM will retain the same LUID. The LUID associated is lost when a power cycle of the AP occurs.
PMP 450 Operations Guide Viewing Session Status (AP) Attribute Meaning Site Name This field indicates the name of the SM. You can assign or change this name on the Configuration web page of the SM. This information is also set into the sysName SNMP MIB-II object and can be polled by an SNMP management server. Software Version This field displays the software release that operates on the SM, the release date and time of the software.
Viewing Session Status (AP) Using Informational Tabs in the GUI Attribute Meaning Re-Reg Count When an SM makes a registration request, the AP checks its local data to see whether it considers the SM to be already registered. If the AP concludes that the SM is not, then the request increments the value of this field. Typically, a Re-Reg is the case where both an SM attempts to reregister for having lost communication with the AP. the AP has not yet observed the link to the SM as being down.
PMP 450 Operations Guide Viewing Session Status (AP) Attribute Meaning Uplink Burst Allocation This field displays the value that is currently in effect for the SM, with the source of that value in parentheses. This is the specified maximum amount of data that each SM is allowed to transmit before being recharged at the Sustained Uplink Data Rate with credits to transmit more. The configuration source of the value is indicated in parentheses.
Viewing Session Status (AP) Using Informational Tabs in the GUI Attribute Meaning Downlink Burst Allocation This field displays the value that is currently in effect for the SM, with the source of that value in parentheses. This is the maximum amount of data to allow the AP to transmit to any registered SM before the AP is replenished with transmission credits at the Sustained Downlink Data Rate. The configuration source of the value is indicated in parentheses.
PMP 450 Operations Guide Interpreting messages in the Event Log Viewing Remote Subscribers (AP) This tab allows you to view the web pages of registered SMs over the RF link. To view the pages for a selected SM, click its link. The General Status tab of the SM opens. Figure 15 Remote Subscribers tab of the AP Interpreting messages in the Event Log Each line in the Event Log of a module Home page begins with a time and date stamp.
Interpreting messages in the Event Log Using Informational Tabs in the GUI A reboot causes the preset time to pause or, in some cases, to run in reverse. Additionally, a power cycle resets the running time and date to the default 00:00:00 UT : 01/01/00. Thus, whenever either a reboot or a power cycle has occurred, you should reset the time and date in the Time & Date web page of any module that is not set to receive sync.
PMP 450 Operations Guide Event Message Interpreting messages in the Event Log Meaning FatalError() The event recorded on the line immediately beneath this message triggered the Fatal Error(). Loss of GPS Sync Pulse Module has lost GPS sync signal. Machine Check Exception This is a symptom of a possible hardware failure. If this is a recurring message, begin the RMA process for the module. RcvFrmNum = 0x00066d ExpFrmNum = 0x000799 Something is interfering with the control messaging of the module.
Viewing the Network Interface Tab (All) Using Informational Tabs in the GUI Messages that Flag Normal Events The messages listed below record normal events and typically do not signal a need for any corrective action or technical support. Figure 17 Event Log messages for normal events Event Message Meaning Acquired GPS Sync Pulse. Module has acquired GPS sync signal. FPGA Features Type of encryption. FPGA Version FPGA (JBC) version in the module. GPS Date/Time Set Module is now on GPS time.
PMP 450 Operations Guide Viewing the Layer 2 Neighbors Tab (AP and SM) Figure 19 Network Interface tab of the SM Viewing the Layer 2 Neighbors Tab (AP and SM) In the Layer 2 Neighbors tab, a module reports any device from which it has received a message in Link Layer Discovery Protocol within the previous two minutes. Given the frequency of LLDP messaging, this means that the connected device will appear in this tab 30 seconds after it is booted and remain until two minutes after its shutdown.
Viewing the Scheduler Tab (AP and SM) Using Informational Tabs in the GUI Viewing the Scheduler Tab (AP and SM) Statistics for the Scheduler are displayed as shown below.
PMP 450 Operations Guide List of Registration Failures (AP) Event Message Meaning In Sync Count Number of times the radio has acquired sync. In the case of an AP generating sync this is when generated sync has been locked, or if GPS synchronization is used it is number of times GPS sync acquired. For the SM, it is the number of times the SM successfully obtained sync with an AP. Out of Sync Count Number of times the radio lost same sync lock.
Translation Table (SM) Using Informational Tabs in the GUI Figure 22 SM Registration Failures tab of the AP Interpreting Data in the Bridging Table (All) If NAT (network address translation) is not active on the SM, then the Bridging Table tab provides the MAC address of all devices that are attached to registered SMs (identified by LUIDs). The bridging table allows data to be sent to the correct module as follows: For the AP, the uplink is from RF to Ethernet.
PMP 450 Operations Guide Translation Table (SM) Translation Table (SM) When Translation Bridging is enabled in the AP, each SM keeps a table mapping MAC addresses of devices attached to the AP to IP addresses, as otherwise the mapping of end-user MAC addresses to IP addresses is lost.
Interpreting Data in the Ethernet Tab (All) Using Informational Tabs in the GUI Interpreting Data in the Ethernet Tab (All) The Ethernet tab of the Statistics web page reports TCP throughput and error information for the Ethernet connection of the module. Figure 25 Ethernet tab of AP The Ethernet tab displays the following fields.
PMP 450 Operations Guide Interpreting Data in the Ethernet Tab (All) Attribute Meaning Innucastpkts Count This field displays how many inbound non-unicast (subnetworkbroadcast or subnetwork-multicast) packets were delivered to a higher-layer protocol. indiscards Count This field displays how many inbound packets were discarded without errors that would have prevented their delivery to a higherlayer protocol. (Some of these packets may have been discarded to increase buffer space.
Interpreting Data in the Ethernet Tab (All) Using Informational Tabs in the GUI Attribute Meaning Late Collision This field displays how many late collisions occurred on the Ethernet controller. A normal collision occurs during the first 512 bits of the frame transmission. A collision that occurs after the first 512 bits is considered a late collision. IMPORTANT! A late collision is a serious network problem because the frame being transmitted is discarded.
PMP 450 Operations Guide Interpreting RF Control Block Statistics in the Radio Tab (All) Interpreting RF Control Block Statistics in the Radio Tab (All) Figure 26 Radio tab of the Statistics page, SM The Radio tab of the Statistics page displays the following fields. Table 25 Radio (Statistics) tab attributes Attribute Meaning inoctets Count This field displays how many octets were received on the interface, including those that deliver framing information.
Interpreting Data in the VLAN Tab (ALL) Using Informational Tabs in the GUI Attribute Meaning outoctets Count This field displays how many octets were transmitted out of the interface, including those that deliver framing information. outucastpkts Count This field displays how many packets for which the higher-level protocols requested transmission to a subnetwork-unicast address. The number includes those that were discarded or not sent.
PMP 450 Operations Guide Viewing Data VC Statistics (All) Unknown—This should not occur. Contact Technical Support. Only Tagged—The packet was filtered because the configuration is set to accept only packets that have an 802.1Q header, and this packet did not. Ingress—When the packet entered through the wired Ethernet interface, the packet was filtered because it indicated an incorrect VLAN membership.
Viewing Data VC Statistics (All) 4-30 Using Informational Tabs in the GUI Attribute Meaning inucastpkts This field displays how many inbound subnetwork-unicast packets were delivered to a higher-layer protocol. innucastpkts This field displays how many inbound non-unicast (subnetworkbroadcast or subnetwork-multicast) packets were delivered to a higherlayer protocol.
PMP 450 Operations Guide Viewing Summary Information in the Overload Tab (All) Viewing Summary Information in the Overload Tab (All) The Overload tab displays statistics on packet overload and resultant packet discards. Unlike the other fields, the Total Packets Overload Count is expressed in only this tab. It is not a count of how many packets have been lost, but rather of how many discard events (packet loss bursts) have been detected due to overload condition.
Viewing ARP Statistics (SM) Using Informational Tabs in the GUI Viewing Filter Statistics (SM) The Filter tab displays statistics on packets that have been filtered (dropped) due to the filters set on the Protocol Filtering tab. Figure 30 Filter tab of the SM Viewing ARP Statistics (SM) The ARP tab in an SM module correlated the IP address of the Ethernet-connected device to its MAC address and provides data about the connection.
PMP 450 Operations Guide Viewing NAT Statistics (SM) Viewing NAT Statistics (SM) When NAT is enabled on an SM, statistics are kept on the Public and Private (WAN and LAN) sides of the NAT, and displayed on the NAT Stats tab.
Viewing NAT DHCP Statistics (SM) Using Informational Tabs in the GUI Attribute Meaning Public NAT Statistics, Failed Hash Insert Count This field represents the number of times the NAT table for the SM‘s WAN/wireless interfaces has been filled.
PMP 450 Operations Guide Interpreting Data in the GPS Status Page (AP) Attribute Meaning PktToss Unsupported MsgType Count This field represents the number of packets tossed due to the receipt of an unsupported message type (cannot be interpreted by DHCP client) PktToss XID Mismatch Count The field represents the number of packets that were tossed due to a transaction ID mismatch PktToss NoSID Count This field represents the number of packets that were tossed due to lack of a DHCP session ID PktTo
Accessing PPPoE Statistics About Customer Activities (SM) Using Informational Tabs in the GUI Accessing PPPoE Statistics About Customer Activities (SM) When the PPPoE feature has been enabled in the SM, the PPPoE statistics provide data about the activities of the customer.
PMP 450 Operations Guide Accessing PPPoE Statistics About Customer Activities (SM) Attribute Meaning PPPoE Control Bytes Sent This field displays the total number of PPPoE session control bytes sent from the SM PPPoE Control Bytes Received This field displays the total number of PPPoE session control bytes received by the SM PPPoE Data Session Bytes Sent This field displays the total number of PPPoE data session (noncontrol/non-session management user data) sent by the SM PPPoE Data Session Bytes
Viewing Bridge Control Block Statistics (All) Using Informational Tabs in the GUI Viewing Bridge Control Block Statistics (All) The AP and SM Bridge Control Block Statistics tab is shown below: Figure 35 Bridge Control Block statistics Table 30 Bridge Control Block Statistics attributes 4-38 Attribute Meaning FEC bin This field indicates the number of broadcast packets received by the bridge control block on the Ethernet interface FEC bout This field indicates the number of broadcast packets sent
PMP 450 Operations Guide Viewing Bridge Control Block Statistics (All) Attribute Meaning FEC btoss This field indicates the number of broadcast packets tossed out by the bridge control block on the Ethernet interface FEC btosscap This field indicates the number of broadcast packets tossed out at the Ethernet interface due to MIR cap being exceeded.
Viewing Bridge Control Block Statistics (All) 4-40 Using Informational Tabs in the GUI Attribute Meaning ErrBridgeFull This field indicates the total number of times the bridging table was full and could not accept new entries ErrApFecQSend This field indicates that a packet which was received on the Ethernet interface could not be processed because the radio bridge queue was full. The packet was tossed out.
PMP 450 Operations Guide Using the Spectrum Analyzer Tool Chapter 5: Using Tools in the GUI The AP and SM GUIs provide several tools to analyze the operating environment, system performance, and networking, including: Using the Spectrum Analyzer Tool on page 5-1 Using the Alignment Tool (SM) on page 5-7 Using the Link Capacity Test Tool (AP or SM) on page 5-8 Using the AP Evaluation Tool (SM) on page 5-11 Using the OFDM Frame Calculator Tool for Collocation (AP or SM) on page 5-14 Using the Subscriber Con
Graphical spectrum analyzer display Using Tools in the GUI Vary the days and times when you analyze the spectrum in an area. The RF environment can change throughout the day or throughout the week. Temporarily deploy an SM for each frequency band range that you need to monitor and access the Spectrum Analyzer tab in the Tools web page of the module. To enter the scan mode and view readings, click Enable.
PMP 450 Operations Guide Using the AP as a Spectrum Analyzer Enabling ―Perform Spectrum Analysis on Boot for configured Duration‖ will increase SM registration time by the amount of seconds specified for the SM to scan the spectrum upon boot. Figure 37 Spectrum analyzer results Colors in the display have the following meanings: Green bars show the most recent measurements. Yellow ticks show the maximum measurements from the current spectrum analysis session.
Using the AP as a Spectrum Analyzer Using Tools in the GUI If you are connected to an AP through one of its SMs and mistakenly change the AP into an SM, you will lose connectivity and will need to gain access to the Ethernet side of the AP through another part of your network to change it back into an AP. To transform a VLAN-disabled AP into an SM for spectrum analysis and then return the device to an AP, perform the following steps.
PMP 450 Operations Guide Using the AP as a Spectrum Analyzer If you reboot an AP that has a configured Management VID parameter and Device Type parameter set to SM, you are automatically removing the AP from the Management VLAN. The following procedure enables you to successfully analyze the spectrum and return to management via the VLAN feature. In many cases, it is advisable to use this procedure to transform all APs in a cluster into SMs.
Using the Remote Spectrum Analyzer Tool (AP) Using Tools in the GUI 15 Click the Reboot button. RESULT: Connectivity to the module is lost. 16 Access the AP through its Management VLAN. NOTE: How you do this depends on your local configuration. You may need to connect to the appropriate tagging port of the VLAN switch in your NOC. Using the Remote Spectrum Analyzer Tool (AP) The Remote Spectrum Analyzer tool in the AP provides additional flexibility in the use of the spectrum analyzer in the SM.
PMP 450 Operations Guide Using the Alignment Tool (SM) This feature proceeds in the following sequence: 1. The AP de-registers the target SM. 2. The SM scans (for the duration set in the AP tool) to collect data for the bar graph. 3. The SM re-registers to the AP. 4. The AP displays the bar graph. The bar graph is an HTML file, but can be changed to an XML file, which is then easy to analyze through the use of scripts that you may write for parsing the data.
Using the Link Capacity Test Tool (AP or SM) Using Tools in the GUI Figure 41 Alignment Tool tab of SM, poor RF environment Using the Link Capacity Test Tool (AP or SM) The Link Capacity Test page allows you to measure the throughput and efficiency of the RF link between two modules. Many factors, including packet length, affect throughput. The Link Capacity Test tab contains the settable parameter Packet Length with a range of 64 to 1522 bytes.
PMP 450 Operations Guide Using the Link Capacity Test Tool (AP or SM) Table 31 Link Capacity Test tab attributes Attribute Meaning RF Link Test: Fully tests radio-to-radio communication, but does not bridge traffic. Link Test with Bridging: Bridges traffic to ―simulated‖ Ethernet ports, providing a status of the bridged link. Link Test Mode Link Test with Bridging and MIR: Bridges traffic during the test but also adheres to any MIR (Maximum Information Rate) settings for the link.
Using the Link Capacity Test Tool (AP or SM) Using Tools in the GUI Figure 43 Link Capacity Test tab with 1522-byte packet length 5-10 pmp-0049 (September 2012)
PMP 450 Operations Guide Using the AP Evaluation Tool (SM) To run a simple link capacity test that floods the link with 1522 byte packets for 10 seconds, perform the following procedure: Procedure 5 Performing a simple Link Capacity Test 1 Access the Link Capacity Test tab in the Tools web page of the module. 2 Select Link Test Mode Link Test with Bridging 3 Select the subscriber module to test using the Current Subscriber Module parameter.
Using the AP Evaluation Tool (SM) Using Tools in the GUI The AP Evaluation tab provides the following fields that can be useful to manage and troubleshoot a system: Table 32 AP Evaluation tab attributes Attribute Meaning Index This field displays the index value that the system assigns (for only this page) to the AP where this SM is registered. Frequency This field displays the frequency that the AP transmits. ESN This field displays the MAC address (electronic serial number) of the AP.
PMP 450 Operations Guide Using the AP Evaluation Tool (SM) Attribute Meaning EBcast A 1 in this field indicates the AP or BHM is encrypting broadcast packets. A 0 indicates it is not. Session Count This field displays how many sessions the SM (or BHS) has had with the AP (or BHM). Typically, this is the sum of Reg Count and Re-Reg Count. However, the result of internal calculation may display here as a value that slightly differs from the sum.
Using the OFDM Frame Calculator Tool for Collocation (AP or SM) Using Tools in the GUI Attribute Meaning AP Gain This field displays the total external gain (antenna) used by the AP. RcvT This field displays the AP‘s configured receive target for receiving SM transmissions (this field affects automatic SM power adjust). Sector ID This field displays the value of the Sector ID field that is provisioned for the AP.
PMP 450 Operations Guide Using the OFDM Frame Calculator Tool for Collocation (AP or SM) Max Range Downlink Data percentage (reserved) Control Slots If OFDM (PMP 430, PMP 450, PTP 230) and FSK (PMP 1x0) APs of the same frequency band are in proximity, or if you want APs set to different parameters (differing in their Max Range values, for example), then you should use the Frame Calculator to identify compatible settings. The frame calculator is available on the Frame Calculator tab of the Tools web page.
Using the OFDM Frame Calculator Tool for Collocation (AP or SM) Using Tools in the GUI Figure 45 OFDM Frame Calculator tab In the Frame Calculator tab, you may set the following parameters. Table 33 OFDM Frame Calculator tab attributes 5-16 Attribute Meaning Link Mode For AP to SM frame calculations, select Multipoint Link Platform Type AP/BHM Use the drop-down list to select the hardware series (board type) of the AP.
PMP 450 Operations Guide Using the OFDM Frame Calculator Tool for Collocation (AP or SM) Attribute Meaning Downlink Data Initially set this parameter to the same value that the AP has for its Downlink Data parameter (percentage). Then, as you use the Frame Calculator tool in Procedure 6, you will vary the value in this parameter to find the proper value to write into the Downlink Data parameter of all APs in the cluster. PMP 450 Series APs offer a range of 15% to 85%, and default to 75%.
Using the OFDM Frame Calculator Tool for Collocation (AP or SM) Using Tools in the GUI The Calculated Frame Results display several items of interest: Table 34 OFDM Calculated Frame Results attributes Attribute Meaning Modulation The type of radio modulation used in the calculation (OFDM for PMP 450) Total Frame Bits The total number of bits used in the calculated frames Data Slots (Down/Up) A result within the typical range is 61/21, meaning 61 control (half) slots down and 21 control (half) slots
PMP 450 Operations Guide Using the OFDM Frame Calculator Tool for Collocation (AP or SM) Procedure 6 Using the Frame Calculator 1 Populate the OFDM Frame Calculator parameters with appropriate values as described above. 2 Click the Calculate button. 3 Scroll down the tab to the Calculated Frame Results section 4 Record the value of the AP Receive Start field 5 Enter a parameter set from another AP in the system – for example, an AP in the same cluster that has a higher Max Range value configured.
Using the Subscriber Configuration Tool (AP) Using Tools in the GUI Using the Subscriber Configuration Tool (AP) The SM Configuration tab in the Tools page of the AP displays: the current values whose control may be subject to the setting in the Configuration Source parameter. an indicator of the source for each value. This tab may be referenced for information on how the link is behaving based on where the SM is retrieving certain QoS and VLAN parameters.
PMP 450 Operations Guide Reviewing the Link Status Tool Results (AP) Reviewing the Link Status Tool Results (AP) The Link Status Tool displays information about the most-recent Link Test initiated on the SM. Link Tests initiated from the AP are not included in the Link Status table. This table is useful for monitoring link test results for all SMs in the system. Figure 47 Link Status tab of AP The Link Status tool results include values for the following fields.
Reviewing the Link Status Tool Results (AP) BER Results Using Tools in the GUI This field displays the over-the-air Bit Error Rates for each downlink. (The ARQ [Automatic Resend reQuest] ensures that the transport BER [the BER seen end-to-end through a network] is essentially zero.) The level of acceptable over-the-air BER varies, based on operating requirements, but a reasonable value for a good link is a BER of 1e-4 (1 x 10-4) or better, approximately a packet resend rate of 5%.
PMP 450 Operations Guide Using the Throughput Monitoring Tool (AP) Using the BER Results Tool (SM) Radio BER data represents bit errors at the RF link level. Due to CRC checks on fragments and packets and ARQ (Automatic Repeat reQuest), the BER of customer data is essentially zero. Radio BER gives one indication of link quality. Other important indications to consider include the received power level, signal to noise ratio, and link tests.
Using the Throughput Monitoring Tool (AP) Using Tools in the GUI Figure 49 Throughput tab of the AP The following configuration parameters are available on the Throughput tab GUI pane, and a radio reboot is not required when configuring these parameters: Table 36 Congested AP Indicator attributes Attribute Meaning Throughput Monitoring This enables or disables the monitoring of sector throughput and packet discards. This parameter is disabled by default.
PMP 450 Operations Guide Using the Throughput Monitoring Tool (AP) o kbps out – average throughput over the collection interval in Kbps out of the AP on the Ethernet Interface o PPS in – average packets per second over the collection interval into the AP on the Ethernet Interface o PPS out – average packets per second over the collection interval out of the AP on the Ethernet Interface RF Throughput - Statistics collected at the RF Interface: o kbps in – average throughput over the collection inter
Using the Sessions Tool (AP) Using Tools in the GUI o outPkts – Number of packets sent by the AP at the RF Interface over the collection interval o Discards (in/out) – Number of packets that had to be discarded by the AP at the respective RF Interface Queue during the collection interval o Discards % (in/out) – Percent of the total packets received / transmitted that had to be discarded during the collection interval LUID RF Throughput Stats This table contains a row that corresponds to each active
PMP 450 Operations Guide Using the Sessions Tool (AP) Figure 50 Sessions tab of the AP pmp-0049 (September 2012) 5-27
PMP 450 Operations Guide Typical Upgrade Process Chapter 6: Maintaining Your Software Cambium provides release compatibility information and caveats about each release. For the latest information and caveats about each software release, see the release notes available for download from http://www.cambiumnetworks.com/support/pmp/software/index.php.
Rebranding Module Interface Screens Maintaining Your Software Rebranding Module Interface Screens Distinctive fonts indicate literal user input. variable user input. literal system responses. variable system responses. The interface screens on each module display the Cambium logo. The logo is a hyperlink, and clicking on it takes the user to the Canopy web site. A different site (perhaps the operator‘s support site) can be made the destination using the procedures below.
PMP 450 Operations Guide 3 Rebranding Module Interface Screens Use a telnet session and the addwebfile command to add the new file to the file system. Supported telnet commands execute the following results: addwebfile adds a custom logo file to the file system. clearwebfile clears the logo file from the file system. lsweb lists the custom logo file and display the storage space available on the file system. >telnet ModuleIPAddress /---------\ C A N O P Y Cambium Networks (Copyright 2001-2012 Cambium Ne
Setting Up a Protocol Analyzer on Your Network Maintaining Your Software If you need to restore the original logo and hyperlink in a module, perform the following steps. Procedure 10 Returning a module to its original logo and hyperlink 1 Use a telnet session and the clearwebfile command to clear all custom files from the file system of the module >telnet ModuleIPAddress /---------\ C A N O P Y Cambium Networks (Copyright 2001-2012 Cambium Networks) Login: root Password: Telnet
PMP 450 Operations Guide Setting Up a Protocol Analyzer on Your Network The equipment required to set up a protocol analyzer includes: 1 hub Some Ethernet switches have a monitor mode (also called 'port mirroring', 'port monitoring‘). To ensure that all packets are captured, set up a monitoring port on the hub/switch to monitor/mirror the ports to which the PMP 450 equipment and premises are connected.
Setting Up a Protocol Analyzer on Your Network Maintaining Your Software Analyzing traffic at an AP with no CMM The IP address of the protocol analyzer laptop computer must match the IP addressing scheme of the AP. If the router is configured to be a DHCP server, then configure the laptop computer to automatically obtain an address. If DHCP is not enabled, then ensure that the laptop computer is configured with a static IP address in the same subnet as the AP.
PMP 450 Operations Guide Setting Up a Protocol Analyzer on Your Network Figure 53 Protocol analysis at AP connected to a CMM CMM AP 8 J1 to 7 radio 6 5 4 3 2 1 J2 Ethernet to Switch 8 7 6 5 4 3 2 1 Ethernet Switch Hub Router Sniffer Laptop pmp-0049 (September 2012) 6-7
Setting Up a Protocol Analyzer on Your Network Maintaining Your Software Example of a protocol analyzer setup for an SM The following is an example of a network protocol analyzer setup using Wireshark software to capture traffic at the SM level. This example is based on the following assumptions: All required physical cabling has been completed. The hub, protocol analyzer laptop computer, and subscriber PC are successfully connected. Wireshark software is operational on the laptop computer.
PMP 450 Operations Guide 5 Setting Up a Protocol Analyzer on Your Network The captured packets are displayed in the main window: pmp-0049 (September 2012) 6-9
PMP 450 Operations Guide General planning for troubleshooting Chapter 7: Troubleshooting General planning for troubleshooting Effective troubleshooting depends in part on measures that you take before you experience trouble in your network. Cambium recommends the following measures for each site: Identify troubleshooting tools that are available at your site (such as a protocol analyzer). Identify commands and other sources that can capture baseline data for the site.
General fault isolation process Troubleshooting General fault isolation process Effective troubleshooting also requires an effective fault isolation methodology that includes attempting to isolate the problem to the level of a system, subsystem, or link, such as o o AP to SM AP to CMM o AP to GPS o CMM to GPS o BHM to BHS o BHM to CMM o power researching Event Logs of the involved equipment interpreting messages in the Event Log answering the questions listed in the following section.
PMP 450 Operations Guide Secondary Steps Secondary Steps After preliminary fault isolation through the above steps check the Canopy knowledge base (http://www.cambiumnetworks.com/forum/) to find whether other network operators have encountered a similar problem. proceed to any appropriate set of diagnostic steps.
Procedures for Troubleshooting Troubleshooting Procedures for Troubleshooting Module Has lost or does not establish connectivity To troubleshoot a loss of connectivity, perform the following steps. Procedure 12 Troubleshooting loss of connectivity 1 Isolate the end user/SM from peripheral equipment and variables such as routers, switches, and firewalls. 2 Set up the minimal amount of equipment. 3 On each end of the link check the cables and connections.
PMP 450 Operations Guide 5 Procedures for Troubleshooting On each end of the link access the General tab in the Configuration page of each module. verify that the setting for Link Speeds (or negotiation) matches that of the other module. access the Radio tab in the Configuration page of each module. verify that the Radio Frequency Carrier setting is checked in the Custom Radio Frequency Scan Selection List. verify that the Color Code setting matches that of the other module.
Procedures for Troubleshooting Troubleshooting NAT/DHCP-configured SM has lost or does not establish connectivity Before troubleshooting this problem, identify the NAT/DHCP configuration from the following list: NAT with DHCP Client (DHCP selected as the Connection Type of the WAN interface) and DHCP Server NAT with DHCP Client (DHCP selected as the Connection Type of the WAN interface) NAT with DHCP Server NAT without DHCP To troubleshoot a loss of connectivity for an SM configured for NAT/DHCP, perform
PMP 450 Operations Guide Procedures for Troubleshooting SM Does Not Register to an AP To troubleshoot an SM failing to register to an AP, perform the following steps. Procedure 14 Troubleshooting SM failing to register to an AP 1 Access the Radio tab in the Configuration page of the SM. 2 Note the Color Code of the SM. 3 Access the Radio tab in the Configuration page of the AP. 4 Verify that the Color Code of the AP matches that of the SM. 5 Note the Radio Frequency Carrier of the AP.
Procedures for Troubleshooting Troubleshooting Module has lost or does not gain sync To troubleshoot a loss of sync, perform the following steps. Procedure 15 Troubleshooting loss of sync 1 Access the Event Log tab in the Home page of the SM 2 Check for messages with the following format: RcvFrmNum = ExpFrmNum = 3 If these messages are present, check the Event Log tab of another SM that is registered to the same AP for messages of the same type.
PMP 450 Operations Guide Procedures for Troubleshooting Module does not establish Ethernet connectivity To troubleshoot a loss of Ethernet connectivity, perform the following steps. Procedure 16 Troubleshooting loss of Ethernet connectivity 1 Verify that the connector crimps on the Ethernet cable are not loose. 2 Verify that the Ethernet cable is not damaged. 3 If the Ethernet cable connects the module to a network interface card (NIC), verify that the cable is pinned out as a straight-through cable.
Procedures for Troubleshooting Troubleshooting Module does not power on To troubleshoot the failure of a module to power up, perform the following steps. Procedure 17 Troubleshooting failure to power on 1 Verify that the connector crimps on the Ethernet cable are not loose. 2 Verify that the Ethernet cable is not damaged.
PMP 450 Operations Guide Procedures for Troubleshooting CMM does not pass proper GPS sync to connected modules If the Event Log tabs in all connected modules contain Loss of GPS Sync Pulse messages, perform the following steps. Procedure 19 Troubleshooting CMM not passing sync 1 Verify that the GPS antenna has an unobstructed view of the entire horizon. 2 Verify that the GPS coaxial cable meets specifications. 3 Verify that the GPS sync cable meets specifications for wiring and length.
Procedures for Troubleshooting Troubleshooting Module Functions Properly, Except Web Interface Became Inaccessible If a module continues to pass traffic, and the SNMP interface to the module continues to function, but the web interface to the module does not display, perform the following steps. Procedure 21 Restoring web management GUI access 1 Enter telnet DottedIPAddress. RESULT: A telnet session to the module is invoked. 2 At the Login prompt, enter root.
Chapter 8: Reference information This chapter contains reference information and regulatory notices that apply to the PMP 450 Series products. The following topics are described in this chapter: Equipment specifications on page 8-2 contains specifications of the AP, SM and other equipment required for PMP 450 installations. Wireless specifications on page 8-7 contains specifications of the PMP 450 wireless interface, including RF bands, channel width and link loss.
AP specifications Reference information Equipment specifications This section contains specifications of the AP, SM, associated supplies required for PMP 450 installations. AP specifications The PMP 450 AP conforms to the specifications listed in the table below. These specifications apply to all PMP 450 product variants.
PMP 450 Operations Guide AP specifications Category Specification Maximum Deployment Range Up to 40 km (25 mi) Subscribers Per Sector Up to 46 (Release 12.
SM specifications Reference information Category Specification Maximum Power Consumption 18 W Input Voltage 29 V Security Encryption 56-bit DES Certifications FCC ID Z8H89FT0002 Industry Canada Cert 109W-0002 SM specifications The PMP 450 SM conforms to the specifications below. These specifications apply to all PMP 450 product variants.
PMP 450 Operations Guide SM specifications Category Specification Protocols Used IPv4, UDP, TCP, IP, ICMP, SNMP, HTTP, FTP, RADIUS Network Management HTTP, FTP, SNMP v2c, Syslog VLAN 802.1ad (DVLAN Q-in-Q), 802.1Q with 802.
SM specifications Reference information Category Specification Dimensions (H x W x D) 30 x 9 x 9 cm (11.75‖ x 3.4‖ x 3.
PMP 450 Operations Guide Wireless specifications This section contains specifications of the PMP 450 wireless interface. These specifications include RF bands, channel bandwidth, spectrum settings, maximum power and link loss. General wireless specifications Table 39 lists the wireless specifications that apply to all PMP 450 variants. Table 39 PMP 450 wireless specifications Item Specification Channel selection Manual selection (fixed frequency).
Ethernet interface Reference information Data network specifications This section contains specifications of the PMP 450 Ethernet interface. Ethernet interface The PMP 450 Ethernet port conforms to the specifications listed below: Table 40 Ethernet bridging specifications Ethernet Bridging Specification Protocol IEEE 802.3 compatible QoS IEEE 802.1p, IEEE 802.1Q, IEEE 802.
PMP 450 Operations Guide Human exposure to radio frequency energy Compliance with safety standards This section lists the safety specifications against which the PMP 450 has been tested and certified. It also describes how to keep RF exposure within safe limits. Electrical safety compliance The PMP 450 hardware has been tested for compliance to the electrical safety specifications listed in Table 41. Table 41 PMP 450 safety compliance specifications Region Specification USA UL 60950 Canada CSA C22.
Human exposure to radio frequency energy Reference information Directive 2004/40/EC of the European Parliament and of the Council of 29 April 2004 on the minimum health and safety requirements regarding the exposure of workers to the risks arising from physical agents (electromagnetic fields) (18th individual Directive within the meaning of Article 16(1) of Directive 89/391/EEC). US FCC limits for the general population. See the FCC web site at http://www.fcc.
PMP 450 Operations Guide d Human exposure to radio frequency energy distance from point source, in m Rearranging terms to solve for distance yields: d P.G 4 .S Calculated distances and power compliance margins Table 43 shows calculated minimum separation distances, recommended distances and resulting margins for each frequency band and antenna combination. These are conservative distances that include compliance margins.
Human exposure to radio frequency energy Reference information Table 43 Power compliance margins Freq. Band Antenna 5.8 GHz OFDM Variable d Recommended Separati on Distance Power Compliance Margin P G S (calc ulated ) Integrated SM, 9 dBi patch 0.158 W (22 dBm) 7.9 (9 dB) 10 W/m2 10 cm 20 cm (8 in) 40.27 Integrated SM, 9 dBi patch with 5.5 dBi LENS 0.158 W (22 dBm) 28 (14.5 dB) 10 W/m2 18.7 cm 50 cm (20 in) 71.01 Integrated SM, 9 dBi patch with 14 dBi Reflector Dish 0.
PMP 450 Operations Guide Human exposure to radio frequency energy If there are no EIRP limits in the country of deployment, use the distance calculations for FCC 5.8 GHz for all frequency bands.
FCC compliance testing Reference information Compliance with radio regulations This section describes how the PMP 450 complies with the radio regulations that are enforced in various countries. Changes or modifications not expressly approved by Cambium could void the user‘s authority to operate the system. Type approvals This system has achieved Type Approval in various countries around the world. This means that the system has been tested against various local technical regulations and found to comply.
PMP 450 Operations Guide Region Codes Notwithstanding that Cambium has designed (and qualified) the PMP 450 products to generally meet the Class B requirement to minimize the potential for interference, the PMP 450 product range is not marketed for use in a residential environment. Region Codes Table 45 lists the region codes available on PMP 450 AP and SM units.
FCC and ICC IDs and certification numbers Reference information Table 46 Region Code transmit power regulation Radio/ Frequency Channel Size PMP 450 AP 5.
PMP 450 Operations Guide FCC ID Z8H89FT0002 Z8H89FT0001 Z8H89FT0001 Z8H89FT0001 Industry Canada Cert Number FCC and ICC IDs and certification numbers Frequencies Module Families Antenna (OFDM) Maximum Combined Tx Output Power 109W-0002 20 MHz channels, centered on 5735-5840 in 5 MHz increments (within the 5725-5850 MHz ISM band) 5780APC 17 dBi Connectorized 19 dBm 109W-0001 20 MHz channels, centered on 5735-5840 in 5 MHz increments (within the 5725-5850 MHz ISM band) 5790SM 9 dBi Integra
PMP 450 regulatory compliance Reference information Notifications This section contains notifications of compliance with the radio regulations that are enforced in various regions. PMP 450 regulatory compliance The PMP 450 complies with the regulations that are enforced in the USA and Canada. The relevant notifications are specified in this section. PMP 450 FCC and IC notification U.S. Federal Communication Commission (FCC) and Industry Canada (IC) Notification.
PMP 450 Operations Guide PMP 450 regulatory compliance Where necessary, the end user is responsible for obtaining any National licenses required to operate this product and these must be obtained before using the product in any particular country. Contact the appropriate national administrations for details on the conditions of use for the bands in question and any exceptions that might apply.
PMP 450 Operations Guide Glossary Appendix A: Glossary I Term Definition 10Base-T Technology in Ethernet communications that can deliver 10 Mb of data across 328 feet (100 meters) of CAT 5 cable. 169.254.0.0 Gateway IP address default in Cambium fixed wireless broadband IP network modules. 169.254.1.1 IP address default in Cambium fixed wireless broadband IP network modules. 255.255.0.
PMP 450 Operations Guide II Glossary Term Definition APs MIB Management Information Base file that defines objects that are specific to the Access Point Module. See also Management Information Base. ARP Address Resolution Protocol. A protocol defined in RFC 826 to allow a network element to correlate a host IP address to the Ethernet address of the host. See http://www.faqs.org/rfcs/rfc826.html. ASN.1 Abstract Syntax Notation One language.
PMP 450 Operations Guide Glossary Term Definition chkconfig A command that the Linux® operating system accepts to enable MySQL® and Apache™ Server software for various run levels of the mysqld and httpd utilities. Cluster Management Module Module that provides power, GPS timing, and networking connections for an AP cluster. Also known as CMM. If this CMM is connected to a Backhaul Module, then this CMM is the central point of connectivity for the entire site. CMM Cluster Management Module.
PMP 450 Operations Guide IV Glossary Term Definition DiffServ Differentiated Services, consistent with RFC 2474. A byte in the type of service (TOS) field of packets whose values correlates to the channel on which the packet should be sent. The value is a numeric code point. Cambium modules map each of 64 code points to values of 0 through 7. Three of these code points have fixed values, and the remaining 61 are settable.
PMP 450 Operations Guide Glossary Term Definition Fieldprogrammable Gate Array Array of logic, relational data, and wiring data that is factory programmed and can be reprogrammed. File Transfer Protocol Utility that transfers of files through TCP (Transport Control Protocol) between computing devices that do not operate on the same platform. Defined in RFC 959. See http://www.faqs.org/rfcs/rfc959.html. FPGA Field-programmable Gate Array.
PMP 450 Operations Guide VI Glossary Term Definition HTTP Hypertext Transfer Protocol, used to make the Internet resources available on the World Wide Web. Defined in RFC 2068. See http://www.faqs.org/rfcs/rfc2068.html. ICMP Internet Control Message Protocols defined in RFC 792, used to identify Internet Protocol (IP)-level problems and to allow IP links to be tested. See http://www.faqs.org/rfcs/rfc792.html.
PMP 450 Operations Guide Glossary Term Definition Late Collision Field This field displays how many late collisions occurred on the Ethernet controller. A normal collision occurs during the first 512 bits of the frame transmission. A collision that occurs after the first 512 bits is considered a late collision. A late collision is a serious network problem because the frame being transmitted is discarded.
PMP 450 Operations Guide VIII Glossary Term Definition NBI See Northbound Interface. NEC National Electrical Code. The set of national wiring standards that are enforced in the U.S.A. NetBIOS Protocol defined in RFC 1001 and RFC 1002 to support an applications programming interface in TCP/IP. This interface allows a computer to transmit and receive data with another host computer on the network. RFC 1001 defines the concepts and methods. RFC 1002 defines the detailed specifications.
PMP 450 Operations Guide Glossary Term Definition Point-toMultipoint Protocol Defined in RFC 2178, which specifies that data that originates from a central network element can be received by all other network elements, but data that originates from a non-central network element can be received by only the central network element. See http://www.faqs.org/rfcs/rfc2178.html. Also referenced as PMP. PPPoE Point to Point Protocol over Ethernet.
PMP 450 Operations Guide X Glossary Term Definition RF Radio frequency. How many times each second a cycle in the antenna occurs, from positive to negative and back to positive amplitude. RJ-11 Standard cable that is typically used for telephone line or modem connection. RJ-45 Standard cable that is typically used for Ethernet connection. This cable may be wired as straight-through or as crossover. Later modules auto-sense whether the cable is straight-through or crossover.
PMP 450 Operations Guide Glossary Term Definition Static IP Address Assignment Assignment of Internet Protocol address that can be changed only manually. Thus static IP address assignment requires more configuration time and consumes more of the available IP addresses than DHCP address assignment does. RFC 2050 provides guidelines for the static allocation of IP addresses. See http://www.faqs.org/rfcs/rfc2050.html. See also DHCP.
PMP 450 Operations Guide XII Glossary Term Definition Textual Conventions MIB Management Information Base file that defines system-specific textual conventions. See also Management Information Base. Tokens Theoretical amounts of data. See also Buckets. TOS 8-bit field in that prioritizes data in a IP transmission. See http://www.faqs.org/rfcs/rfc1349.html. TxUnderrun Field This field displays how many transmission-underrun errors occurred on the Ethernet controller. UDP User Datagram Protocol.
