Model: 20L05 20” 4:3 Digital LCD Television/ PC Monitor Operating Manual http://wintal.com.au Manual 20L05.
Manual 20L05.
TABLE OF CONTENTS 1. PreFace 1 2. Safety Precautions 1 3. Front, Back Connections 2 4. TV Installation Guide 3 4.1 Connecting Antennas 3 4.2 AV Video Input 3 4.3 S-Video Input 3 4.4 YcbCr Connection 4 4.5 PC Connection 4 5. Manual 20L05.indd c Configuration 5 5.1 Auto Search 5 5.2 Manual Search 5 5.3 Fine Tune 5 5.4 Save Settings 5 5.5 Skip 5 6. Picture Setting 6 7. Audio Setting 6 8. Source Setting 6 9. Language Select 7 10. Lock 7 11.
1. PREFACE Congratulations on your purchase of a Wintal LCD! Please read this manual thoroughly before operating the monitor. Make sure the monitor was not damaged in transit. Should the monitor be damaged, do not install it and contact your dealer. Check that you have all the accessories according to the model. 2. SAFETY PRECAUTIONS Place the Monitor on a stable surface. Do not use the monitor with other fixations than those provided or suggested by the manufacturer.
3. FRONT, BACK CONNECTIONS Front View and Controls Back View Rear Connections Wintal LCD | 2 Manual 20L05.
4. TV INSTALLATION GUIDE 4.1 Connecting Antennas To ensure good picture and sound, TV antenna system needs to be installed. The antenna system as shown can be sourced from TV equipment shops, which will provide service for correct installation and connection. After installation, insert the 75-ohm antenna plug into the antenna jack as shown. 4.2 AV Video Input 4.3 S-Video Input 3 | Wintal LCD Manual 20L05.
4.4 YcbCr Connection To connect to the RGB/ Component input on your DVD player, also use the supplied S-Video -> Component Adaptor. 4.5 PC Connection Wintal LCD | 4 Manual 20L05.
5. CONFIGURATION 5.1 Auto Search • • • • • Press «MENU» key on the front control panel or «SYS MENU» key on the remote control to go into the menu Then press ◄ or ► to access the menu below Before selecting «Auto search», choose the «Colour system» and the «Sound system» with ▲ or ▼ Select « Auto search » with ▲ or ▼ Press ◄ or ► to confirm 5.
• • 6. • • • • 7. • • • • 8.
9. • • • • 10.
14. PC SETTING • • • Set up the LCD to PC mode by changing the «MODE» key on remote control Switch on PC with a contrast ratio 800*600 /60Hz Connect the LCD to the PC with the VGA cable • Press «MENU» key on the front panel or «SYS MENU» on the remote control to go into the menu Press ◄ or ► to access the menu above Press ▲ or ▼ to select the setting you wish to adjust Adjust with ◄ or ► • • • Wintal LCD | 8 Manual 20L05.
15.
16. a. b. c. REMOTE CONTROL SETUP Open the cover Insert the supplied “AA” size batteries When inserting the batteries, make sure correct polarities as per the “+” and “-” marks on the batteries are correct Replace the battery cover 16.1 Battery Usage Caution To prevent battery leakage which may result in injury or damage to the remote: 1. 2. 3. 17. Install all batteries correctly, and as marked on the remote control Do not mix batteries: (OLD and NEW or CARBON and ALKALINE, etc.
18. TROUBLESHOOTING & ADVICE Before calling our Customer Centre, please check if you can the following suggestions will solve your problem. Troubleshooting No signal Incorrect colour shades Control Please check that all cables and connectors are correctly plugged in.
19. SPECIFICATIONS Screen Size 20.1 Inch Display Type LCD TFT Resolution(Pixel) 800 x 600 Brightness 500 cd / m² Color 24 bit ( 16,777,216) Contrast Ratio 500 : 1 View Angle(H/V) Horizontal 160,Vertical 140, CR10 Aspect Ratio 4:3 Power 100-240 VAC, 12V 50/60HZ. Power consumption 60W TV System PAL / NTSC Video Input Format PAL / NTSC Antenna Input Standard antenna socket 75 Ω Audio Output L / R 3W + 3W VGA Input 800 x 600 60HZ Input Output RGB 0.
