Specifications
Table Of Contents
- Home
- Table of Contents
- 1 General Information 1-1
- 2 EBC-BX Technical Reference 2-1
- 2.1 Introduction 2-1
- 2.2 Intel FW82443BX / SMSC Victory-66 Chipset 2-1
- 2.3 Memory Installation 2-1
- 2.4 Interrupt Routing 2-2
- 2.5 Power/Reset Connections 2-3
- 2.6 Mouse Interface 2-3
- 2.7 Real Time Clock/Calendar 2-4
- 2.8 Keyboard Interface 2-4
- 2.9 Serial Interface 2-5
- 2.10 Parallel Printer Port 2-12
- 2.11 Speaker/Sound Interface 2-12
- 2.12 PC/104 Bus Interface 2-12
- 2.13 PC/104 Plus Bus Interface 2-13
- 2.14 Floppy Disk Interface 2-14
- 2.15 IDE Hard Disk Interface 2-15
- 2.16 Watchdog Timer Configuration 2-16
- 2.17 Status LED 2-16
- 2.18 Battery Select Control 2-16
- 2.19 DiskOnChip Configuration 2-17
- 2.20 Parallel I/O 2-18
- 2.21 VGA Configuration 2-21
- 2.22 Ethernet Controller 2-23
- 2.23 Fan Power Connector 2-24
- 2.24 Multi I/O Connector 2-25
- 2.25 USB Connector 2-25
- 2.26 Jumper Connector Summary 2-26
- 3 AWARD BIOS Configuration 3-1
- 3.1 General Information 3-1
- 3.2 Entering Setup 3-1
- 3.3 Setup Main Menu 3-1
- 3.4 Standard CMOS Features 3-2
- 3.5 Advanced BIOS Features Setup 3-6
- 3.6 Chipset Features Setup 3-11
- 3.7 Integrated Peripherals Setup 3-14
- 3.8 Power Management Setup 3-19
- 3.9 PNP/PCI Configuration 3-23
- 3.10 PC Health Status 3-25
- 3.11 Frequency/Voltage Control 3-25
- 3.12 Load BIOS Defaults 3-26
- 3.13 Set Supervisor Password 3-27
- 3.14 Set User Password 3-27
- 3.15 Save and Exit Setup 3-27
- 3.16 Exit without Saving 3-27
- 4 EBC-BX DiskOnChip Configuration 4-1
- 5 WS16C48 Programming Reference 5-1
- APPENDIX A I/O Port Map
- APPENDIX B Interrupt Map
- APPENDIX C EBC-BX Parts Placement Guide
- APPENDIX D EBC-BX Parts List
- APPENDIX E EBC-BX Mechanical Drawing
- APPENDIX F WS16C48 I/O Routines and Sample Program Listings
- Warranty and Repair Information

COM2 - RS- 485
Im por tant Note : All se rial ter mi na tion com po nents are sur face mount 0805 pack ages. These
should only be in stalled by sur face mount quali fied in di vidu als.
2.9.3 SAE J1708 Con figu ra tion
The So ci ety of Auto mo tive En gi neers (SAE) J1708 in ter face is a varia tion of the RS- 485 in ter face
which is used for “Se rial Data Com mu ni ca tions be tween Mi cro com puter Sys tems in Heavy Duty Ve hi -
cle Ap pli ca tions”. It is be yond the scope of this docu ment to go into de tail on the J1708 speci fi ca tion.
The EBC- BX may be user con fig ured for J1708 by the ad di tion of the CK- 75176-2 “Chip Kit”. One
“Chip Kit” is suf fi cient to con fig ure both chan nels for J1708. The il lus tra tions that fol l ow show the cor -
rect jump er ing, driver IC in stal la tion, I/O con nec tor pin defi ni tions, and the ter mi na t ion net work de tails
for each of the chan nels when used in J1708 mode.
Page 2 - 10 OPERATIONS MANUAL EBC-BX 030923
WinSystems - "The Embedded Systems Authority"
3 2 1
o o o
1 2 3
o o o
U6 - Not In stalled
U10 - In stalled
U7 - Not In stalled
1 o o 6
2 o o 7
3 o o 8
4 o o 9
5 o
J16 J18
COM2 DB9
N/C
TX/RX+
TX/RX-
N/C
GND
N/C
N/C
N/C
N/C
VCC
TX/RX+
TX/RX-
R103
R104
R105
RS- 485 NOTE : Be cause RS- 485 uses a sin gle
twisted- pair, all trans mit ters are con nected in par al -
lel. Only one sta tion at a time may trans mit or have
its trans mit ter en abled. The trans mit ter En able/Dis -
able is con trolled in soft ware us ing bit 1 in the Mo -
dem Con trol Reg is ter (RTS). When RTS is set, the
trans mit ter is en abled, and when cleared (the nor mal
state) the trans mit ter is dis abled and the re ceiver is
en abled. Note that it is nec es sary to al low some
mini mal set tling time af ter ena bling the trans mit ter
bef ore trans mit ting the first char ac ter. Like wise, fol -
low ing a trans mis sion, it is nec es sary to be sure that
all char ac ters have been com pletely shifted out of
the UART (Check Bit 6 in the Line Status Reg is ter)
bef ore dis abling the trans mit ter to avoid chop ping
off the last char ac ter.