K&D Factory Service Inc.
HA4502 Holding Cabinet CVAP HA45 Holding Cabinet (Non Surface Mounted Controls) CVAP HA45 Holding Cabinet (Surface Mounted Controls) Parts Manual Parts Manual Parts Manual International Parts Manual CVAP CC, CB, CG (Differential Controls) CA75 HB35 Parts Maual Parts Manual “D” Models Parts Manual “S” Models Parts Manual Property of K&D Factory Service Inc.
Commodore Thermalizer Parts Identification Manual For service information call 1-800-234-5286 1 Lit.
Commodore Thermalizer Table of Contents Photo Reference …………………………………………………………………..3-6 Parts Descriptions & Order numbers ……………………………………………7-8 How to Use This Manual Use photo reference (pages 3-6) to identify parts. Match photo reference numbers with parts descriptions and order numbers (pages 7-8). 2 Lit.
Commodore Thermalizer Parts Identification Note: See pages 7-8 for descriptions and order numbers. 3 Lit.
Commodore Thermalizer Parts Identification Note: See pages 7-8 for descriptions and order numbers. 4 Lit.
Commodore Thermalizer Parts Identification Note: See pages 7-8 for descriptions and order numbers. 5 Lit.
Commodore Thermalizer Parts Identification Note: See pages 7-8 for descriptions and order numbers. 6 Lit.
Commodore Thermalizer Parts Identification Photo Reference Number 1 7 Part Description Order Number Power Switch Rocker Type Toggle Type PS2304 PS1529 2 Hinge Kit PS2116 3 Non-locking Caster PS2147 4 Drip Cup & Retainer PS2182 5 Locking Caster PS2146 6 Handle PS1774 7 Door Gasket PS2150 8 Flue 9 Removable Shelf PS2305 10 Evaporator Cover PS2365 11 Air Heater PS2368 12 Air Probe PS2178 13 Water Probe PS2177 14 Water Heater Top Element Bottom Element PS2367 PS2366 1
8 PS2098 17 Cooling Fan 18 Power Cord Strain Relief REF. ONLY 19 Program Lock Key Switch REF. ONLY 20 Circulation Fan Motor Starting Capacitor REF. ONLY 21 High Limit Thermostat PS2369 22 Transformer Board PS2172 23 Contactor (Magnetic) PS1007 24 Buzzer Assembly PS1589 25 Power Board PS2354 26 Door Switch PS2372 27 Control Board PS2203 28 Circulating Fan Motor PS2119 Lit.
Winston Breader/Sifter Parts Identification Manual 2345 Carton Drive Louisville, KY 40299 USA (800) 234-5286 (502) 495-5400 To order parts, contact your Winston representative or call the International office: Winston Products Co. (800) 234-5286 USA & Canada/USA TEL: (502) 495-5400/USA FAX: (502) 495-5458 Lit.
WINSTON BREADER/SIFTER Table of Contents Photo Reference .......................................................................................................... 1 - 3 Parts Descriptions & Order Numbers ........................................................................... 4 How To Use This Manual Use Photo Reference (pages 1 - 3) to identify parts. Match Photo Reference numbers with Parts Descriptions and Order Numbers (page 4).
WINSTON BREADER/SIFTER Parts Identification NOTE: See page 4 for Parts Descriptions and Order Numbers 1 4 2 5 3 6 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON BREADER/SIFTER Parts Identification NOTE: See page 4 for Parts Descriptions and Order Numbers 7 8 9 11 12 10 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON BREADER/SIFTER Parts Identification NOTE: See page 4 for Parts Descriptions and Order Numbers 13 14 15 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON BREADER/SIFTER Parts Identification Photo Reference Number Part Description Order Number 1 Cover Ref.
Winston Hot Foods Merchandiser Parts Identification Manual 2345 Carton Drive Louisville, KY 40299 USA (800) 234-5286 (502) 495-5400 To order parts, contact your Winston representative or call the International office: Winston Products Co. (800) 234-5286 USA & Canada/USA TEL: (502) 495-5400/USA FAX: (502)Lit. 495-5458 #4275R86 Rev.
WINSTON HOT FOODS MERCHANDISER Table of Contents Photo Reference .......................................................................................................... 1 - 4 Parts Descriptions & Order Numbers ........................................................................... 5 - 6 Wiring Diagram ............................................................................................................ 7 How To Use This Manual Use Photo Reference (pages 1 - 4) to identify parts.
WINSTON HOT FOODS MERCHANDISER Parts Identification NOTE: See page 5 - 6 for Parts Descriptions and Order Numbers 1 2 3 6 4 5 7 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON HOT FOODS MERCHANDISER Parts Identification NOTE: See page 5 - 6 for Parts Descriptions and Order Numbers 8 9 10 11 12 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON HOT FOODS MERCHANDISER Parts Identification NOTE: See page 5 - 6 for Parts Descriptions and Order Numbers 15 13 13 17 16 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON HOT FOODS MERCHANDISER Parts Identification NOTE: See page 5 - 6 for Parts Descriptions and Order Numbers 18 19 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON HOT FOODS MERCHANDISER Parts Identification Photo Reference Number Part Description Order Number 1 Front Glass (2 Pan) Front Glass (3 Pan) Front Glass (4 Pan) Front Glass (5 Pan) HPS1612 HPS1611 HPS1610 HPS1840 2 Back Glass (2 Pan) Back Glass (3 Pan) Back Glass (4 Pan) Back Glass (5 Pan) HPS1613 HPS1614 HPS1615 HPS1839 3 Door Assembly (2 Pan) Door Assembly (3 Pan) Door Assembly (4 Pan-Left Side) Door Assembly (4 Pan-Right Side) Door Assembly (5 Pan-Left Side) Door Assembly (5 Pan-Right Sid
WINSTON HOT FOODS MERCHANDISER Parts Identification Photo Reference Number Part Description Order Number 8 Short Adapter HPS1513 9 Long Adapter (2, 3, 4 Pan) Long Adapter (5 Pan) HPS1515 HPS1968 10 Drain Cap HPS1654 11 Drain Pipe HPS1833 12 Water Heaters HPS1437 13 Switch Guard HPS1086 14 Evaporator Heat Lamp HPS1103 15 Dimmer Switch Dials HPS1250 16 Power Switch HPS1529 17 Dimmer Switches HPS1528 18 Heat Lamps (250 W, 120 Volt Infra-Red) Ref.
WINSTON HOT FOODS MERCHANDISER Wiring Schematic To order parts, contact your Winston representative or call the International office: Winston Products Co.
HBA0/5 ‘D’ SERIES Parts Identification Manual HBA5D2 SHOWN Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 1 of 12 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5D SERIES TABLE OF CONTENTS Exploded view – Back Interior Assembly ……………………...……....……….. 3 Exploded view – Bottom Assembly………………………………….....……….. 4 Exploded view – Tank Assembly………………………………….....……...….. 5 Exploded view – Probe Assemblies………………………………….....……….. 6 Exploded view - Cabinet Assembly……………………....…………………….. 7 Exploded view – Drawer Cabinet Assembly……………………....……....…….. 8 Exploded view – Drawer Assembly………………………………….....………..
WINSTON CVAP MODEL HBA0/5D SERIES BACK INTERIOR ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 3 of 12 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5D SERIES BOTTOM ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 4 of 12 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5D SERIES TANK ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 5 of 12 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5D SERIES PROBE ASSEMBLIES Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 6 of 12 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5D SERIES CABINET ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 7 of 12 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5D SERIES DRAWER CABINET ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 8 of 12 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5D SERIES DRAWER ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 9 of 12 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5D SERIES ESCUTCHEON CONTROL ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 10 of 12 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5D SERIES FAN ASSEMBLY (HBA5 MODELS ONLY) Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 11 of 12 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5D SERIES SCHEMATIC (HBA0 MODELS DO NOT HAVE FAN) Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 12 of 12 4272Y356rev00_09-02-03_partsID_HBA0-5D.
HBA0/5 ‘N’ SERIES Parts Identification Manual HBA5N1 SHOWN Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 1 of 11 4272Y404rev00_11-10-03_partsID_HBA0-5N.
WINSTON CVAP MODEL HBA0/5N SERIES TABLE OF CONTENTS Exploded view – Bottom Assembly ..……………………...……....……………. 3 Exploded view – Cabinet Assembly………………………………….....……….. 4 Exploded view – Drawer Assembly……………………………….....……...….. 5 Exploded view – Cabinet & Drawer Assembly…………………….....………… 6 Exploded view – Escutcheon / Control Assembly……………………………….. 7 Exploded view – Fan Assembly……………………………....……....…………. 8 Exploded view – Probe Assembly………………………………….....………….
WINSTON CVAP MODEL HBA0/5N SERIES BOTTOM ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 3 of 11 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5N SERIES CABINET ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 4 of 11 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5N SERIES DRAWER ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 5 of 11 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5N SERIES CABINET & DRAWER ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 6 of 11 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5N SERIES ESCUTCHEON / CONTROL ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 7 of 11 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5N SERIES FAN ASSEMBLY (HBA5 MODELS ONLY) Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 8 of 11 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5N SERIES PROBE ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 9 of 11 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5N SERIES TANK ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 10 of 11 4272Y356rev00_09-02-03_partsID_HBA0-5D.
WINSTON CVAP MODEL HBA0/5N SERIES SCHEMATIC (HBA0 MODELS DO NOT HAVE FAN) Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 11 of 11 4272Y356rev00_09-02-03_partsID_HBA0-5D.
HBK, L, M, 8, 0 or 5 ‘D’ SERIES Parts Identification Manual Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 1 of 12 4272Z046rev00_03-16-04_partsID_HBK-L-M-80-5D.
WINSTON CVAP MODEL HBK,L,M,80-5,D SERIES TABLE OF CONTENTS Exploded view – Back Interior Assembly ……………………...……....……….. 3 Exploded view – Bottom Assembly………………………………….....……….. 4 Exploded view – Tank Assembly………………………………….....……...….. 5 Exploded view – Probe Assemblies………………………………….....……….. 6 Exploded view - Cabinet Assembly……………………....…………………….. 7 Exploded view – Drawer Cabinet Assembly……………………....……....…….. 8 Exploded view – Drawer Assembly………………………………….....………..
WINSTON CVAP MODEL HBK,L,M,80-5,D SERIES BACK INTERIOR ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 3 of 12 4272Z046rev00_03-16-04_partsID_HBK-L-M0-5D.
WINSTON CVAP MODEL HBK,L,M,80-5,D SERIES BOTTOM ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 4 of 12 4272Z046rev00_03-16-04_partsID_HBK-L-M0-5D.
WINSTON CVAP MODEL HBK,L,M,80-5,D SERIES TANK ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 5 of 12 4272Z046rev00_03-16-04_partsID_HBK-L-M0-5D.
WINSTON CVAP MODEL HBK,L,M,80-5,D SERIES PROBE ASSEMBLIES Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 6 of 12 4272Z046rev00_03-16-04_partsID_HBK-L-M0-5D.
WINSTON CVAP MODEL HBK,L,M,80-5,D SERIES CABINET ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 7 of 12 4272Z046rev00_03-16-04_partsID_HBK-L-M0-5D.
WINSTON CVAP MODEL HBK,L,M,80-5,D SERIES DRAWER CABINET ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 8 of 12 4272Z046rev00_03-16-04_partsID_HBK-L-M0-5D.
WINSTON CVAP MODEL HBK,L,M,80-5,D SERIES DRAWER ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 9 of 12 4272Z046rev00_03-16-04_partsID_HBK-L-M0-5D.
WINSTON CVAP MODEL HBK,L,M,80-5,D SERIES ESCUTCHEON CONTROL ASSEMBLY Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 10 of 12 4272Z046rev00_03-16-04_partsID_HBK-L-M0-5D.
WINSTON CVAP MODEL HBK,L,M,80-5,D SERIES FAN ASSEMBLY (HBK,L,M,85 MODELS ONLY) Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 11 of 12 4272Z046rev00_03-16-04_partsID_HBK-L-M0-5D.
WINSTON CVAP MODEL HBK,L,M,80-5,D SERIES SCHEMATIC (model numbers with '0' in the forth character do not have fan) Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 12 of 12 4272Z046rev00_03-16-04_partsID_HBK-L-M0-5D.
PF46C and PF56C Pressure Fryer Parts Identification Manual Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com 4272X639_rev04_10-05-05_partsID_PF46/56C.
Table of Contents Main Assembly…………………………………………………………………….page 1 Vent Muffler Assembly……………………………………………………………page 2 Vent Assembly……………………………………………………………………..page 3 Pot Assembly………………………………………………………………………page 4 Lid Assembly………………………………………………………………………page 5 Escutcheon (front) Assembly………………………………………………………page 6 Relay Panel Assembly……………………………………………………………...page 7 Schematic – Delta Configuration…………………………………………………...
6 SYM. Qty 1 1 2 1 3 1 4 1 5 2 6 1 7 1 8 2 9 2 10 1 11 1 3 4 1 KIT NO. REF ONLY PS1399 PS1400 PS1210 PS1318 PS1459 REF ONLY PS1934 PS1226-2 REF ONLY PS1933 FRYER ASSEMBLY DESCRIPTION POT ASSEMBLY BLOCK FRONT ASSEMBLY BLOCK REAR ASM BACKSPLASH PANEL BACKSPLASH LABEL LID ASSEMBLY VENT/MUFFLER ASSEMBLY LEG ASSEMBLY REAR WHEEL ASSEMBLY (QTY 2) ESCUTCHEON ASSEMBLY LEG ASSEMBLY FRONT 5 2 7 10 7 8 9 11 Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.
2 3 1 SYM Qty 1 1 2 1 3 1 1 1 VENT/MUFFLER ASSEMBLY KIT NO. DESCRIPTION BACK VENT ASSEMBLY PS1156 MUFFLER PS1152 VENT ASSEMBLY - 6HD 11.9PSI PS1686 VENT ASSEMBLY - 4HD 11.9PSI PS1653 VENT ASSEMBLY - 4HD 14.0PSI PS1458 Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 2 of 9 4272X639rev04_10-05-05_partsID_PF46/56C.
7 14 2 5 1 13 8 4 6 9 3 11 12 10 SYM Qty KIT NO. 1 REF ONLY 1 1 PS1039 2 1 PS1040 1 PS2180 1 PS1321 3 4 1 PS1088 1 PS1075 5 1 PART OF #4 6 1 PS1073 7 1 PS1072 1 PS1071 1 REF ONLY 8 1 PS1684 9 1 PS1026 1 PS1322 10 11 1 PS1005 12 1 PS1704 4 REF ONLY 13 1 PS1320 14 15 1 REF ONLY VENT ASSEMBLY DESCRIPTION VENT WELD ASSEMBLY WEIGHT LIFTER - 6HD 11.9PSI WEIGHT LIFTER - 4HD 11.9PSI WEIGHT LIFTER - 4HD 14.0PSI BRACKET SOLENOID SOLENOID SLIDE SOLENOID TOP (PART OF PS1088) WEIGHT - 6HD 11.
SYM. QTY KIT NO.
7 5 8 4 9 3 6 SYM. 1 2 3 4 5 6 7 8 9 2 Qty 1 1 1 1 1 1 1 1 1 LID ASSEMBLY KIT NO. DESCRIPTION PS1057 RETAINER ASM PS1028 SPRING PS1449 LID LOCK PS1046 LID BOTTOM LOCK ASM PS1168 HANDLE PS1891 LID GASKET REF ONLY LABEL LID LOCK "DANGER" PS1127 LID VALVE PS1010 LID VALVE O-RING 1 Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 5 of 9 4272X639rev04_10-05-05_partsID_PF46/56C.
SYM. Qty 1 1 2 1 3 1 4 1 5 1 6 1 10 4 11 2 12 2 13 3 14 1 15 1 16 1 16 4 11 2 ESCUTCHEON ASSEMBLY KIT NO. DESCRIPTION PS1529 SWITCH POWER PS2302 SWITCH POWER INTERLOCK REF ONLY RELAY PANEL ASSEMBLY REF ONLY BRACKET SWITCH REF ONLY ESCUTCHEON PS1086 GUARD SWITCH REF ONLY NUT KEPS 8-32 REF ONLY RETAINER STRIP REF ONLY SCREW 6-32x .
5 2 4 5 5 4 5 3 2 2 2 2 2 SYM 1 2 3 4 5 Qty 1 6 1 2 2 4 RELAY PANEL ASSEMBLY KIT NO. DESCRIPTION REF ONLY PANEL RELAY FRYER PS1271 GROMMET REF ONLY BUSHING PANEL 1.375 PS1007 RELAY - US ONLY PS2299 RELAY - ALL OTHERS SCREW REF ONLY 1 Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 7 of 9 4272X639rev04_10-05-05_partsID_PF46/56C.
DELTA Configuration Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 8 of 9 4272X639rev04_10-05-05_partsID_PF46/56C.
WYE Configuration Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 9 of 9 4272X639rev04_10-05-05_partsID_PF46/56C.
Winston Collectramatic Fryer - 'P' Control Parts Identification Manual 2345 Carton Drive Louisville, KY 40299 USA (800) 234-5286 (502) 495-5400 To order parts, contact your Winston representative or call the International office: Winston Products Co. (800) 234-5286 USA & Canada/USA TEL: (502) 495-5400/USA FAX: (502) 495-5458 Lit.
WINSTON COLLECTRAMATIC FRYER Table of Contents Photo Reference .......................................................................................................... 1 - 8 Parts Descriptions & Order Numbers ........................................................................... 9 - 13 How To Use This Manual Use Photo Reference (pages 1 - 8) to identify parts. Match Photo Reference numbers with Parts Descriptions and Order Numbers (pages 9 - 13).
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 6 - 7 for Parts Descriptions and Order Numbers 12 1 3 2 4 5 6 7 8 9 11 10 17 18 19 16 20A 20B 14 (Inside) 15 (Hidden) 21 (Hidden) 13 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 5 for Parts Descriptions and Order Numbers 22 23 24 25 24 (Reference Only) 19 9 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 6 - 7 for Parts Descriptions and Order Numbers 29 (Under) 27 28 21 26 30 15 31 36 35 34 32 33 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 6 - 7 for Parts Descriptions and Order Numbers 37 38 39 40 42 (Behind) 41 43 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 6 - 7 for Parts Descriptions and Order Numbers 44 45 47 46 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 6 - 7 for Parts Descriptions and Order Numbers 48 49 50 51 53 52 (Reference Only) 54 (Under) To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 6 - 7 for Parts Descriptions and Order Numbers 55 54 52 56 57 59 58 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 6 - 7 for Parts Descriptions and Order Numbers 60 30 11 29 61 65 62 63 64 66 67 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 1 Danger Panel PS1210 2 Latch Block (Front) (Pressure Lock) PS1399 3 Hinge Block (Rear) PS1400 4 Eyebrow PS1134 5 Switch Guard PS1086 6 Hi Limit Indicator Lamp PS1012/3 7 Heat On Indicator Lamp PS1012/3 8 Power On Indicator Lamp PS1012/3 9 Membrane Panel (General Market) Membrane Panel (KFC) PS1748 PS1932 10 Leg Front PS1933 11 Collector PS1206 12 Lid Pressure Lock PS1
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 16 Mercury Relay PS1448 17 Electromechanical Relay PS1007 18 Power Board (General Market) Power Board (KFC) PS1800 PS1971 19 EMI Filter PS1977 20A Fuse Holder PS1096/2 20B Fuse PS1095/6 21 Thermister Probe PS2040 22 Buzzer PS1586 23 Transformer PS1687 24 Computer (General Market) Computer (KFC) Ref. Only Ref.
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 29 Collector Gasket PS1892/3 30 Heat Plate PS1034 31 High Limit Thermostat Clamp PS1312 32 Leg Rear With Wheel PS1934 33 Wheel Assembly PS1226/2 34 Leg Clamp Assembly PS1621 35 Muffler PS1152 36 Back Panel (4 HD) Back Panel (6 HD) PS1697 PS1698 37 Vent Back Cap PS1729 38 Vent Back Assembly PS1156 39 Vent Assembly (4 HD) - GM Vent Assembly (4 HD) - KFC Dom.
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 42 Teflon Slide PS1075/3 43 Vent Block Assembly (4 HD) Vent Block Assembly (6 HD) PS1026 PS1684 44 Vent Tube (4 HD) Vent Tube (6 HD) PS1322 PS1678 45 Vent Solenoid Spring PS1320/3 46 Vent Solenoid PS1088 47 Vent Solenoid Cotter Pin PS1121/3 48 Drain Valve PS1066 49 Drain Valve Handle PS1695 50 Lid Valve Assembly PS1127 51 Lid Valve Spring PS1028/3 52 Lid Valve Body Ref.
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 57 Vent Block Assembly (4 HD) Vent Block Assembly (6 HD) PS1026 PS1684 58 Vent Tube O'Ring PS1005/3 59 Vent Block Nut Plate PS1704/6 60 Clamshell Basket (4 HD) Clamshell Basket (6 HD) PS1159 PS1163 61 Lid Gasket 62 Black Nylon Brush PS1025/1 63 White Teflon Brush PS1120/1/12 64 Drain Valve Extension PS1211 65 Drain Hook With Handles PS1154/1/6 66 Plugging Tool PS1179/1 67 D
Winston Products International, Ltd. Collectramatic Fryer - 'P' Control International Parts Identification Manual Winston Products International, Ltd. Lit.
WINSTON COLLECTRAMATIC FRYER Table of Contents Photo Reference .......................................................................................................... 1 - 8 Parts Descriptions & Order Numbers ........................................................................... 9 - 13 How To Use This Manual Use Photo Reference (pages 1 - 8) to identify parts. Match Photo Reference numbers with Parts Descriptions and Order Numbers (pages 9 - 13). Winston Products International, Ltd.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 9 - 13 for Parts Descriptions and Order Numbers 12 1 3 2 4 5 6 8 7 9 11 10 17 18 19 16 20A 20B 14 (Inside) 15 (Hidden) 21 (Hidden) 13 Winston Products International, Ltd.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 9 - 13 for Parts Descriptions and Order Numbers 22 23 24 25 24 (Reference Only) 19 9 Winston Products International, Ltd.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 9 - 13 for Parts Descriptions and Order Numbers 29 (Under) 27 28 21 26 30 15 31 36 35 34 32 33 Winston Products International, Ltd.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 9 - 13 for Parts Descriptions and Order Numbers 37 38 39 40 42 (Behind) 41 43 Winston Products International, Ltd.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 9 - 13 for Parts Descriptions and Order Numbers 44 45 47 46 Winston Products International, Ltd.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 9 - 13 for Parts Descriptions and Order Numbers 48 49 50 51 53 52 (Reference Only) 54 (Under) Winston Products International, Ltd.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 9 - 13 for Parts Descriptions and Order Numbers 55 54 52 56 57 59 58 Winston Products International, Ltd.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See page 9 - 13 for Parts Descriptions and Order Numbers 60 30 11 29 61 65 62 63 64 66 67 Winston Products International, Ltd.
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 1 Danger Panel PS1210 2 Latch Block (Front) (Bottom Lock) PS1399 3 Hinge Block (Rear) PS1400 4 Eyebrow PS1134 5 Switch Guard PS1086 6 Hi Limit Indicator Lamp PS1012/3 7 Heat On Indicator Lamp PS1012/3 8 Power On Indicator Lamp PS1012/3 9 Membrane Panel PS1932 10 Leg Front PS1933 11 Collector PS1206 12 Lid Bottom Lock PS1046 13 Insulation Front Sections (4 HD & 6 HD)
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 16 Mercury Relay PS1448 17 Electromechanical Relay PS2157 18 Power Board PS1971 19 EMI Filter PS1977 20A Fuse Holder PS1096/2 20B Fuse PS1095/6 21 Thermister Probe PS2040 22 Buzzer PS1586 23 Transformer PS1687 24 Process Controller Ref.
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 30 Heat Plate PS1034 31 High Limit Thermostat Clamp PS1312 32 Leg Rear With Wheel PS1934 33 Wheel Assembly PS1226/2 34 Leg Clamp Assembly PS1621 35 Muffler PS1152 36 Back Panel (4 HD) Back Panel (6 HD) PS1697 PS1698 37 Vent Back Cap PS1729 38 Vent Back Assembly PS1156 39 Vent Assembly (4 HD) Vent Assembly (6 HD) PS1653 PS1686 40 Weight (4 HD) (11.9 PSI) Weight (6 HD) (11.
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 43 Vent Block Assembly (4 HD) Vent Block Assembly (6 HD) PS1026 PS1684 44 Vent Tube (4 HD) Vent Tube (6 HD) PS1322 PS1678 45 Vent Solenoid Spring PS1320/3 46 Vent Solenoid PS1088 47 Vent Solenoid Cotter Pin PS1121/3 48 Drain Valve PS1066 49 Drain Valve Handle PS1695 50 Lid Valve Assembly PS1127 51 Lid Valve Spring PS1028/3 52 Lid Valve Body Ref.
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 57 Vent Block Assembly (4 HD) Vent Block Assembly (6 HD) PS1026 PS1684 58 Vent Tube O'Ring PS1005/3 59 Vent Block Nut Plate PS1704/6 60 Clamshell Basket (4 HD) Clamshell Basket (6 HD) PS1159 PS1163 61 Lid Gasket 62 Black Nylon Brush PS1025/1 63 White Teflon Brush PS1120/1/12 64 Drain Valve Extension PS1211 65 Drain Hook With Handles PS1154/1/6 66 Plugging Tool PS1179/1 67 D
Winston Collectramatic® Fryer (Surface Mount 'S' controls) Parts Identification Manual 2345 Carton Drive Louisville, KY 40299 USA (800) 234-5286 (502) 495-5400 To order parts, contact your Winston representative or call the International office: Winston Products Co. (800) 234-5286 USA & Canada/USA TEL: (502) 495-5400/USA FAX: (502) 495-5458 Lit.
WINSTON COLLECTRAMATIC FRYER Table of Contents Photo Reference .......................................................................................................... 1 - 6 Parts Descriptions & Order Numbers ........................................................................... 7 - 10 How To Use This Manual Use Photo Reference (pages 1 - 6) to identify parts. Match Photo Reference numbers with Parts Descriptions and Order Numbers (pages 7 - 10).
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See pages 7 - 10 for Parts Descriptions and Order Numbers To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See pages 7 - 10 for Parts Descriptions and Order Numbers 29 (Under) 27 28 21 26 30 15 31 36 35 34 32 33 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See pages 7 - 10 for Parts Descriptions and Order Numbers 37 38 39 40 42 (Behind) 41 43 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See pages 7 - 10 for Parts Descriptions and Order Numbers 44 45 47 46 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See pages 7 - 10 for Parts Descriptions and Order Numbers 48 49 50 51 53 52 (Reference Only) 54 (Under) To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification NOTE: See pages 7 - 10 for Parts Descriptions and Order Numbers 55 54 52 56 57 59 58 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 1 Danger Panel PS1210 2 Latch Block (Front) (Bottom Lock) PS1399 3 Hinge Block (Rear) PS1400 5 Switch Guard PS1086 6 Hi Limit Indicator Lamp PS2298 7 Heat On Indicator Lamp PS2298 8 Power On Indicator Lamp PS2298 9 Circuit Board Asm Ref.
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 22 Speaker Asm PS2360 25 On/Off Switch PS1529 26 Heater (240 Volt) Heater (208 Volt) PS1148 PS1147 27 Heater Holder PS1430 28 Probe Guard PS1744 29 Collector Gasket PS1892/3 30 Heat Plate PS1034 31 High Limit Thermostat Clamp PS1312 32 Leg Rear With Wheel PS1934 33 Wheel Assembly PS1226/2 34 Leg Clamp Assembly PS1621 35 Muffler PS1152 36 Back Panel (4 HD) Back Panel
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 39 Vent Assembly (4 HD) Vent Assembly (6 HD) PS1653 PS1686 40 Weight (4 HD) Weight (6 HD) PS1071 PS1073 Note: When identifying correct weight for ordering, read PSI engraved on weight lifter.
WINSTON COLLECTRAMATIC FRYER Parts Identification Photo Reference Number Part Description Order Number 52 Lid Valve Body Ref. Only 53 Lid Valve Retainer PS1057 54 Lid Valve O-Ring PS1010/3 55 Lid Lock (Bottom Lock) PS1449 56 Handle Bar (Bottom Lock) PS1168 57 Vent Block Assembly (4 HD) Vent Block Assembly (6 HD) PS1026 PS1684 58 Vent Tube O-Ring PS1005/3 59 Vent Block Nut Plate PS1704/6 NOTE: See pages 1 - 6 for Photo Reference Lit.
SERVICE MANUAL WINSTON COLLECTRAMATIC FRYER 8 CHANNEL MODELS 4 HEAD & 6 HEAD MANUAL REORDER: LIT. 6710/REV.0/9-91 The procedures contained in this manual involve accessing bare electrical terminals and exposure to voltages capable of producing serious injury or death. Any person attempting diagnoisis and/or repair involving removal of panels and/or exposure to live electrical components must be trained or experienced in such service procedures.
INTRODUCTION This Service Manual is to be used for the following WINSTON COLLECIRAMATIC FRYERS: PRESSURE FRYERS OPEN FRYERS MODEL NO. MODEL NO .
TABLE OF CONTENTS PAGE No. INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 - 3 PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1 3 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1 6 AMPERAGE / OHM VALUE CHARTS. . . . . . . . . . . . . . . . . . . 1 7 WlRlNG DIAGRAMS PRESSURE FRYERS . . . . . . . . . . . . . . . . . . . . . . . . . .
1 2 (Inside Lid Groove) 15 3,4, 5,6 16 7 8 17 9 18 10 11 12 19 Escutcheon (Ref Only) 22 ID Tag (Ref Only) 23 13 20 24 14 21 25 WINSTON 4 LIT.6710/REV.
26 27 28 29 31 32 30 (under) 33 High limit Thermostat Bulb (Refrence Only) 34 35 36 WINSTON 5 LIT.6710/REV.
37 38 42 (If Applicable) 39 43 (Behind) 40 44 41 NOTE: 6-Head Model Picture WINSTON 6 LIT.6710/REV.
45 51 46 47 52 53 (Inside) 48 54 (Behind) 49 50 55 WINSTON 7 LIT.6710/REV.
- 61 56 62 (Behind) 57 58 59 60 NOTE: 6-Head Model Pictured WINSTON 8 LIT.6710/REV.
PARTS IDENTIFICATION Photo Item Kit Content Part Description Order Number No. Qty.
PARTS IDENTIFICATION Photo Item Kit Content Part Description No. Order Number Qty.
PARTS IDENTIFICATION Photo Item Kit Content Part Description Order Number No. Qty. Description 30 ‘High Limit’ T’Stat Clamp PS1312 1 1 Clamp Screw 31 Heater Holder PS1430/3 3 Heater Holder 32 Collector Gasket PS1892/3 3 Gasket 33 Heat Plate 14.75” 12.
PARTS IDENTIFICATION Photo Item Kit Content Part Description Order Number No. 40 Insulation 4 - Head 6 - Head Qty.
PARTS IDENTIFICATION Photo Item Kit Content Part Description No. Order Number Qty.
TROUBLESHOOTING SYMPTOMS FAULTS Electric shock while in contact with fryer. DANGER:. .Turn ............. 1 OFF circuit breaker or disconnect fryer from power source Low pressure . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .15,16,17,18,22 No Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19,21,20,22,23,40,4 Pressure loss excessive through Vent in rear of fryer. . . . .19,22,20,21,23 Pressure loss excessive through Lid Valve. . . . . . . . . . . . .
TROUBLESHOOTING REMEDIES CLEAN FAULTS ADJUST REPAIR REPLACE 1 Improper ground, wiring short DANGER: Turn OFF circuit breaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. Open power line Circuit breaker tripped. . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuse blown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cordset not plugged in . . . . . . . . . . . . . . . . . . . . . . . . . . . Faulty power switch. . . . . . . . . . . . . . . . . .
TROUBLESHOOTING FAULTS REMEDIES CLEAN ADJUST REPAIR REPLACE 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. Cotter pin too long or tight (must rotate freely). . . . . . . . . . . Excessive moisture in shortening . . . . . . . . . . . . . . . . . . . . Pin loose in molex connector on computer . . . . . . . . . . . . . . Power board plug loose or off . . . . . . . . . . . . . . . . . . . . . . . Transformer defective . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Probe defective. .
AMPERAGE/OHM VALUE CHARTS NOTE: Resistance measurements are taken across coil of relays and terminal ends on heaters. Wires must be removed from component prior to resistance check. OHM CHART DESCRIPTION OHMIC VALUE PART NO Mercury Relay Watlow Duracool 690.0 OHMS +/- 10% 500.0 OHMS +/- 10% PS1448 PS1448 Electromechanical Relay 225.0 OHMS +/- 10% PS1007 Heater - 208V, 3500W 12.3 OHMS +/- 10% PS1147 Heater - 240V, 3500W 16.
WIRING DIAGRAM FOR MODELS NUMBERS: PF46P32SJ PF56P32SJ PF46P37SJ PF56P37SJ (or (or (or (or M) M) M) M) Model numbers listed are as reflected on Identification Tag. WINSTON 18 LIT.6710/REV.
WIRING DIAGRAM FOR MODELS NUMBERS: PFWPC4201SJ (or M) PFWPC6201SJ (or M) Model numbers listed are as reflected on Identification Tag. WINSTON 19 LIT.6710/REV.
WIRING DIAGRAM FOR MODELS NUMBERS: PFWPC4201CASJ (or M) PFWPC6201CASJ (or M) Model numbers listed are as reflected on Identification Tag. WINSTON 20 LIT.6710/REV.
WIRING DIAGRAM FOR MODELS NUMBERS: PFWPC4201AUSN PFWPC6201AUSN PF46P45SN PF56P45SN PFWPC4201NZSN PFWPC6201NZSN PFWPC4201MASN PFWPC6201MASN PF46P44SN PF56P44SN Model numbers listed are as reflected on Identification Tag. WINSTON 21 LIT.6710/REV.
WIRING DIAGRAM FOR MODELS NUMBERS: OF49P32SJ OF59P32SJ OF49P37SJ OF59P37SJ (orM) (orM) (orM) (orM) Model numbers listed are as reflected on Identification Tag. WINSTON 22 LIT.6710/REV.
WIRING DIAGRAM FOR MODELS NUMBERS: OFWPC4201SJ (or M) OFWPC6201SJ (or M) Model numbers listed are as reflected on Identification Tag. WINSTON 23 LIT.6710/REV.
WIRING DIAGRAM FOR MODELS NUMBERS: OFWPC4201CASJ (or M) OFWPC6201CASJ (or M) Model numbers listed are as reflected on Identification Tag. WINSTON 24 LIT.6710/REV.
WIRING DIAGRAM FOR MODELS NUMBERS: OFWPC4201NZSN OFWPC6201NZSN OFWPC4201MASN OFWPC6201MASN OF49P44SN OF59P44SN OFWPC4201AUSN OFWPC6201AUSN OF49P45SN OF59P45SN Model numbers listed are as reflected on Identification Tag. WINSTON 25 LIT.6710/REV.
REPLACE ELECTROMECHANICAL RELAY (ITEM N0.51) Tools: Phillips Screwdriver #2; Slotted Screwdriver. Procedure: 1. DANGER: Turn off electrical power and disconnect electrical power supply. If unit is hardwired, CIRCUIT BREAKER MUST BE OFF. 2. Remove the two (2) screws securing eyebrow to relay panel and save for reuse. CAUTION: Utilize care in preventing escutcheon from falling forward when removing screws in Step 3. 3. Remove the four (4) screws securing escutcheon to relay panel and save for reuse.
6. Replace the four (4) screws securing new relay to panel. 7. Observing wire location markings, connect wires to proper relay terminals. 8. Replace the four (4) screws securing escutcheon to relay panel. 9. Replace the two (2) screws securing eyebrow to relay panel and place unit back into service. REPLACE TRANSFORMER (ITEM NO. 48) Tools: Phillips Screwdriver #2; Nut Driver -3/8”; Wire Cutters. Procedures: 1. DANGER: Turn off electrical power and disconnect electrical power supply.
CAUTION: Utilize care in preventing escutcheon from falling forward when removing screws in Step 3. 3. Remove the four (4) screws securing escutcheon to relay panel and save for reuse. Lower escutcheon slowly until secure in open position. 4. Remove the two (2) wires attached to fuse holder marking wire locations to ensure proper connection to new fuse holder. 5. Remove the two (2) screws securing fuse holder to relay panel. Save screws and nuts for reuse. 6.
10. Attach wires marked El, E2 and E3 on power board to Ll. L2 and L3 terminals on contactor #l. NOTE: Ll, L2 and L3 terminals on contactor #l are top, middle and bottom terminals respectively. 11. Attach 3-pin plug to power board. 12. Replace the four (4) screws securing escutcheon to relay panel. 13 Replace the two (2) screws securing eyebrow to relay panel and place unit back into service. REPLACE HEATER Tools: (ITEM N0.34) Phillips Screwdriver #2; Nut Driver - 3/8" Nut Driver - 7/16”.
8. Remove lid gaining access to inside of cooking vessel. NOTE: If middle or bottom heater has to be replaced, the heater(s) above the one in question must also be removed to permit access. 9. Remove screw securing high limit thermostat bulb and clamp to top heater coil and save for reuse. 10. Remove screw securing probe guard to second heater coil and save for reuse. 11. Remove the two (2) nuts securing each of the three (3) heater holders to fryer. Save nuts and heater holders for reuse. 12.
22. Replace the four (4) screws securing escutcheon to relay panel. 23. Replace the two (2) screws securing eyebrow to relay panel and place unit back into service. REPLACE Hi LIMIT THERMOSTAT Tools: (ITEM N0. 54) Phillips Screwdriver #2; Slotted Screwdriver; Open End Wrench - 9/16”. Procedure: 1. DANGER: Turn off electrical power, disconnect electrical power supply, dram shortening and allow to cool. If unit is hardwired, CIRCUIT BREAKER MUST BE OFF. 2.
13. Remove the two (2) screws securing thermostat to relay panel and save for reuse. 14. Replace the two (2) screws securing new thermostat to relay panel. NOTE: Verify aluminum washer is in place. bushing prior to Step 14. Washer should be placed flush against 15. Route thermostat bulb through cooking vessel and heater holder. Replace screw securing bulb and clamp to top heater coil. 16. Apply a small amount of silicone sealant to bushing and secure to cooking vessel. 17.
CAUTION: Utilize care to prevent relay panel from falling unsupported when removing screws in Step 5. 5. Remove the four (4) screws securing relay panel to side panels and save for reuse. Lower panel slowly until secure (See Figure 7). 6. Pull down top edge of insulation and remove compression nut securing probe assembly to cooking vessel (See Figure 8). 7. Remove lid gaining access to inside of cooking vessel. 8.
REPLACE ON/OFF SWITCH (ITEM NO.55) Tools: Nut Driver-5/8”; Phillips Screwdriver #2. Procedure: 1. DANGER : Turn off electrical power and disconnect electrical power supply. If unit is hardwired, CIRCUIT BREAKER MUST BE OFF. 2. Remove the two (2) screws securing eyebrow to relay panel and save for reuse. 3. Remove the four (4) screws securing escutcheon to relay panel and save for reuse. CAUTION: 4. Utilize care to prevent escutcheon from falling forward when removing these screws.
2. Move or rotate handle bar to open position. Lift lid above front block and remove from fryer. Depress lid lock removing handle bar from lid and save for reuse. 3. Remove lid lock from lid assembly and save for reuse. 4. Lift lid and hold valve body with other hand. Grasp the lid valve retainer with the other hand and twist counter-clockwise to loosen. 5. Remove lid valve retainer. Note that lid valve spring has closed coil on one end and open coil on the other. Open end goes toward lid.
REPLACE LID VALVE ASSEMBLY (ITEM NO. 3) Tools : Slotted Screwdriver 1/8". Procedure: 1. DANGER: Turn off electrical power and disconnect electrical power supply. If unit is hardwired, CIRCUlT BREAKER MUST BE OFF. 2. Move or rotate handle bar to open position. Lift lid above front block and remove from fryer. Depress lid lock and remove handle bar from lid. Save handle bar for reuse 3. Remove lid lock from lid assembly end save for reuse. 4. Lift Lid and hold valve body with one hand.
REPLACE HEATER HOLDER Tools: (ITEM NO. 31) Nut driver 7/16”; Rubber Mallet. Procedure: 1. DANGER: Turn off electrical power and disconnect electrical power supply; drain shortening and allow to cool. If unit is hardwired, CIRCUIT BREAKER MUST BE OFF. 2. Remove lid from fryer. 3. Remove the two (2) nuts securing heater holder to cooking vessel wall. 4. Utilizing care not to damage heaters, remove heater holder. 5. Replace the two (2) nuts securing new heater holder to cooking vessel wall. 6.
8. Replace the four (4) screws securing escutcheon to relay panel. 9. Replace the two (2) screws securing eyebrow to relay panel and place unit back into service. REPLACE DANGER LABEL PANEL (ITEM NO. 7) Tools: Phillips Screwdriver #2. Procedure: 1. DANGER: Turn off electrical power, disconnect electrical power supply. If unit is hardwired, CIRCUIT BREAKER MUST BE OFF. 2. Place lid in down position. 3. Remove the four(4) screws securing danger label panel to rear of fryer and save for reuse. 4.
hardwired, CIRCUIT BREAKER MUST BE OFF. CAUTION: Utilize care when removing muffler in Step 2. Muffler may contain very hot water. 2. Remove muffler and place in sink. 3. Lift and remove vent back. 4. Remove the seven (7) screws securing Danger Label panel and either left or right back panel (Servicer preference) to rear of fryer and save for reuse. 5. Remove weight from weight lifter. FIG. 10 6. Disconnect the two (2) vent solenoid wires from harness wires at insulated terminals (See Figure 10). 7.
CAUTION: Prior to applying final torque to screws in Step 12, verify solenoid wires are not pinched between nut plate and vent assembly. This could create a shorted circuit causing potential equipment damage and /or personal injury. 12. Place vent block on vent tube, line up nut plate behind vent assembly and replace the four (4) screws securing block to vent tube and vent assembly. 13. Connect vent solenoid wires to harness wires at insulated terminals. 14.
7. Remove the four (4) screws securing vent block and ball (if applicable) to vent assembly. Save screws, block and ball (if applicable) for reuse . NOTE: Some 4-Head and 6-Head models utilize a stainless steel vent ball (located on vent block) with weight to regulate pressure. 8. 9. Remove vent tube O-ring and save for reuse (See Figure14). Remove the four (4) screws securing vent assembly to rear of fryer and save for reuse. Leave vent block nut plate on vent tube for further use. 10.
17. Replace the four (4) screws securing vent assembly to rear of fryer. NOTE: Vent tube must protrude through vent assembly at least l/2" (See Figure 16). 18. Connect the two (2) solenoid wires to harness wires. 19. Place O-ring over vent tube and slide back against vent assembly. CAUTION: Prior to applying final torque to screws in Step 20, verify solenoid wires are not pinched between nut plate and vent assembly.
3. Lift and remove vent back. 4. Remove the seven (7) screws securing Danger Label panel and either left or right back panel (Servicer preference) to rear of fryer. 5. Remove weight from weight lifter. 6. Disconnect the two (2) vent solenoid wires from harness wires at insulated terminals (See Figure 17). 7. Remove the four (4) screws securing vent block to vent assembly. Save screws, block and ball (if applicable) for reuse.
15. Replace the four (4) screws securing vent assembly to rear of fryer. NOTE: Vent tube must protrude through vent assembly at least 1/2” (See Figure 19). 16. Place O-ring over vent tube and slide back against vent assembly. 17. Replace vent block on vent tube and replace four screws securing vent block to vent assembly. Be careful to align the vent block square with the bottom of the weight lifter. 18. Connect vent solenoid wires to harness wires at insulated terminals. 19.
3. Lift and remove vent back. 4. Rmove the seven (7) screws securing Danger Label panel and either left or right back panel (Servicer preference) to rear of fryer and save for reuse. 5. Remove weight from weight lifter. 6. Remove the four (4) screws securing vent block to vent assembly. Save screws, block and ball (if applicable) for reuse. NOTE: Some 4-Head and 6-Head models utilize a stainless steel vent ball (located on vent block) with weight to regulate pressure. 7.
REPLACE WEIGHT LIFTER (ITEM NO. 61) Tools: Slotted Screwdriver; Phillips Screwdriver #2; Needle Nose Pliers. Procedure: 1. DANGER: Turn off electrical power and disconnect electrical power supply. If unit is hardwired, CIRCUIT BREAKER MUST BE OFF. CAUTION: Utilize care when removing muffler in Step 2. Muffler may contain very hot water. 2. Remove muffler and place in sink. 3. Lift and remove vent back and save for reuse. 4. Remove weight and save for reuse. 5.
14. Replace vent spring securing weight lifter to solenoid bracket. Vent spring is mounted between notch in top of vent solenoid bracket and hole in weight lifter arm. NOTE: Utilize care in preventing spring from twisting when replacing. If twisted, undue tension produced could result in a chattering noise and pressure reduction during cook cycle. 15. Manually depress and release weight lifter several times to ensure smooth unrestricted travel prior to reassembly. 16.
CAUTION: Utilize care when removing muffler in Step 2. Muffler may contain very hot water. 2. Remove muffler and place in sink 3. Lift and remove vent back and save for reuse. 4. Remove the 14 screws securing Danger Label panel and rear panels to side panels. Save panels and screws for reuse. 5. Remove weight from weight lifter and save for reuse. 6. Disconnect the two (2) vent solenoid wires from harness wires at insulated terminals (See Figure 24). 7.
CAUTION: Prior to applying final torque to screws in Step 16, verify solenoid wires are not pinched between nut plate and vent assembly. This could create a shorted circuit causing potential equipment damage and/or personal injury. 16. Place vent block on vent tube. Line up nut plate behind vent assembly and replace the four (4) screws securing block to vent tube and vent assembly. 17. Drop vent ball (if applicable) down through waffle onto vent block. 18. Place weight down in weight lifter. 19.
CAUTION: Utilize care when removing muffler in Step 2. Muffler may contain very hot water. 2. Remove muffler and place in sink. 3. Remove lid from fryer. 4. Lift and remove vent back. 5. Remove weight from weight lifter. 6. Remove the 14 screws securing Danger Label panel and back panels to fryer. Save screws and panels for reuse. 7. Disconnect the two (2) vent solenoid wires from harness wires at insulated terminals (See Figure 26). 8.
16. Place vent assembly on rear of fryer noting position of vent tube. Adjust vent tube WITHOUT BENDING matching end of tube with hole in vent assembly. Replace the four (4) screws securing vent assembly to rear of fryer. NOTE: Vent tube must protrude through vent assembly at least 1/2" (See Figure 27). 17. Tighten compression nut securing vent tube to cooking vessel. 18. Connect vent solenoid wires to harness wires. 19. Place o-ring over vent tube and slide back against vent assembly. CAUTION: FIG.
3. Lift and remove vent back. 4. Remove the seven (7) screws securing Danger Label panel and right rear panel to fryer. Save panels and screws for reuse. 5. Remove weight from weight lifter and save for reuse. 6. Disconnect the two (2) vent solenoid wires from harness wires at insulated terminals (See Figure 23). 7. Remove the four (4) screws securing vent block to vent assembly. Save screws, block and ball (if applicable) for reuse. FIG.
CAUTION: Prior to applying final torque to screws, verify solenoid wires are not pinched between nut plate and vent assembly. This could create a shorted circuit causing potential equipment damage and/or personal injury. 16. Place vent block on vent tube, line up nut plate behind vent assembly and replace the four (4) screws securing block to vent tube and vent assembly. 17. Drop vent ball (if applicable) down through waffle onto vent block. 18. Place weight down in weight lifter. 19.
NOTE: Some 4-Head and 6-Head models utilize a stainless steel vent ball (located on vent block) with weight to regulate pressure. 8. Remove vent tube O-ring and discard (See Figure 32). 9. Remove the four (4) screws securing vent assembly to rear of fryer and save for reuse. Leave vent block nut plate on vent tube for further use. 10. Remove vent spring and save for reuse. Note how spring is mounted to bracket and weight lifter to ensure proper installation when replaced. 11.
19. Manually depress and release weight lifter several times to ensure smooth unrestricted travel prior to reassembly. 20. Replace the four (4) screws securing vent assembly to rear of fryer. NOTE: Vent tube must protrude through vent assembly at least 1/2" (See Figure 34). 21. Connect the two (2) solenoid wires to harness wires. 22. Place new O-ring over vent tube and slide back against vent assembly.
4. Remove drain valve. CAUTION: Utilize care not to apply too much torque to drain valve in Step 4 causing bushing connected to fryer to crack or separate from cone. 5. Place locking plate over new drain valve. Note location of holes in drain valve bracket. Holes in locking plate when placed over drain valve must line up with holes in bracket. 6. Apply pipe sealant to threads of new drain valve. 7. Insert new drain valve through bracket and secure to cooking vessel. 8.
REPLACE VENT BLOCK (ITEM NO. 39) Tools: Slotted Screwdriver; Phillips Screwdriver #2. Procedure: 1. DANGER: Turn off electrical power and disconnect electrical power supply. If unit is hardwired CIRCUIT BREAKER MUST BE OFF. CAUTION: Utilize care when removing muffler in Step 2. Muffler may contain very hot water. 2. Remove muffler and place in sink. 3. Lift and remove vent back. 4.
7. Place new O-ring over vent tube and slide back against vent assembly. CAUTION: Prior to applying final torque to screws in Step 8, verify solenoid wires are not pinched between nut plate and vent assembly. This could create a shorted circuit causing potential equipment damage and/or personal injury. 8. Place vent block on vent tube, line up nut plate behind vent assembly and replace the four (4) screws securing block to vent tube and vent assembly. 9.
CAUTION: Utilize care in performing Step 6. Due to location and amount of torque required to remove nuts, wear gloves for protection in the case of wrench slipping. 6. Remove the three (3) nuts securing front block to top of fryer. Remove defective front block. 7. Remove any residue of old silicone sealant from top of fryer. 3. Apply silicone sealant to entire base of new front block and mount on fryer. Place lock washers on bolts end tighten the three (3) nuts securing front block to fryer. 9.
OBTAINING SERVICE ALWAYS REFER TO THE MODEL NUMBER AND SERIAL NUMBER WHEN REQUIRING SERVICE OR WHEN PLACING A PARTS ORDER. Use only genuine Winston Products replacement parts in your appliance. Refer to the parts identification section of this manual to identify the part(s) needed. PROCEDURES FOR REPLACING NEW COMPONENTS ARE INCLUDED IN THIS MANUAL. FOLLOW THOSE INSTRUCTIONS CAREFULLY.
Winston Shortening Filter Parts Identification Manual 2345 Carton Drive Louisville, KY 40299 USA (800) 234-5286 (502) 495-5400 To order parts, contact your Winston representative or call the International office: Winston Products Co. (800) 234-5286 USA & Canada/USA TEL: (502) 495-5400/USA FAX: (502) 495-5458 Lit.
WINSTON SHORTENING FILTER Table of Contents Photo Reference .......................................................................................................... 1 - 3 Parts Descriptions & Order Numbers ........................................................................... 4 - 5 Wiring Diagram ............................................................................................................ 6 How To Use This Manual Use Photo Reference (pages 1 - 3) to identify parts.
WINSTON SHORTENING FILTER Parts Identification NOTE: See pages 4 - 5 for Parts Descriptions and Order Numbers 1 2 3 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON SHORTENING FILTER Parts Identification NOTE: See pages 4 - 5 for Parts Descriptions and Order Numbers 4 5 7 6 9 8 10 13 11 12 14 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON SHORTENING FILTER Parts Identification NOTE: See pages 4 - 5 for Parts Descriptions and Order Numbers 16 15 17 19 18 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON SHORTENING FILTER Parts Identification Photo Reference Number Part Description Order Number 1 Tank Cover HPS2055 2 Wheel HPS1226/2 Caster Assembly (option - not shown for F662 model) HPS2232/2 3 Wheel Bracket HPS1743/2 4 Hose/Wand Assembly HPS1558 5 Filter Hose (7.
WINSTON SHORTENING FILTER Parts Identification Photo Reference Number Part Description Order Number 13 Motor Pump Cover HPS1541 14 Power Cord Bracket HPS1391 15 Pump Assembly HPS1097 16 Power Switch HPS1529 17 Motor HPS1099 18 Pump Line Intake HPS1741 19 Pump Line Output HPS1740 NOTE: See pages 1 - 3 for Photo Reference Lit. #4275R84 - 9/96 To order parts, contact your Winston representative or call the International office: Winston Products Co.
Winston Products International, Ltd. Shortening Filter International Parts Identification Manual Winston Products International, Ltd. Lit.
WINSTON SHORTENING FILTER Table of Contents Photo Reference .......................................................................................................... 1 - 3 Parts Descriptions & Order Numbers ........................................................................... 4 - 5 How To Use This Manual Use Photo Reference (pages 1 - 3) to identify parts. Match Photo Reference numbers with Parts Descriptions and Order Numbers (pages 4 - 5). Winston Products International, Ltd.
WINSTON SHORTENING FILTER Parts Identification NOTE: See pages 4 - 5 for Parts Descriptions and Order Numbers 1 2 3 Winston Products International, Ltd.
WINSTON SHORTENING FILTER Parts Identification NOTE: See pages 4 - 5 for Parts Descriptions and Order Numbers 4 5 7 6 9 8 13 10 11 12 14 Winston Products International, Ltd.
WINSTON SHORTENING FILTER Parts Identification NOTE: See pages 4 - 5 for Parts Descriptions and Order Numbers 16 15 17 19 18 Winston Products International, Ltd.
WINSTON SHORTENING FILTER Parts Identification Photo Reference Number Part Description Order Number 1 Tank Cover HPS2055 2 Wheel HPS1226/2 Caster Assembly (option - not shown for F662 model) HPS2232/2 3 Wheel Bracket HPS1743/2 4 Hose/Wand Assembly HPS1558 5 Filter Hose (7.
WINSTON SHORTENING FILTER Parts Identification Photo Reference Number Part Description Order Number 13 Motor Pump Cover HPS1541 14 Power Cord Bracket HPS1391 15 Pump Assembly HPS1097 16 Power Switch HPS1529 17 Motor HPS1099 18 Pump Line Intake HPS1741 19 Pump Line Output HPS1740 NOTE: See pages 1 - 3 for Photo Reference Lit. #4275R101 - 11/96 Winston Products International, Ltd.
WINSTON CVAP MODEL F552 & F662 SHORTENING FILTER F662A Shortening Filter Parts Identification Manual F662A9 SHOWN Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 1 of 6 DOC050316A_rev01_10-11-05_partsID_F662.
WINSTON CVAP MODEL F552 & F662 SHORTENING FILTER Table of Contents Main Assembly…………………………………………………..………………………….page 3 Model F662 Shown Base Assembly – F662………………………………………………………………………page 4 Base Assembly – F552………………………………………………………………………page 5 Schematic…………………………………………………………………………………….page 6 Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 2 of 6 DOC050316A_rev01_10-11-05_partsID_F662.
WINSTON CVAP MODEL F552 & F662 SHORTENING FILTER Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 3 of 6 DOC050316A_rev01_10-11-05_partsID_F662.
WINSTON CVAP MODEL F552 & F662 SHORTENING FILTER Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 4 of 6 DOC050316A_rev01_10-11-05_partsID_F662.
WINSTON CVAP MODEL F552 & F662 SHORTENING FILTER 5 2 4 1 F552BASE ASM 03094Y08 SYM QTY PART NO DESCRIPTION 1 06408Y02 BASE WELD ASM 1 2 06393Y04 BRACKET MOTOR 2 3 1 01521R01 DRIP GUARD 4 2 06477Y01 WHEEL AND BRACKET ASM 5 4 04098N53 NUT NYLON INSERT 10-32 6 8 04107K31 SCREW 10-32 x .50 TR HD PH 4 04106M03 RIVET POP SS .125 x .125 7 3 6 7 Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.
WINSTON CVAP MODEL F552 & F662 SHORTENING FILTER Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com Page 6 of 6 DOC050316A_rev01_10-11-05_partsID_F662.
WINSTON CVAP MODEL HA4522 Holding Cabinet HA4522 Holding Cabinet Parts Identification Manual Winston Industries, LLC - 2345 Carton Dr. - Louisville - Kentucky - 40299 www.cvap.com 1-800-234-5286 502-495-5400 FAX 502-495-5458 www.winstonindustries.com DOC050408Arev00_04-19-05_HA4522_exploded_view.
WINSTON CVAP MODEL HA4522 Holding Cabinet HA4522 MAIN ASM SYM QTY PART NO.
WINSTON CVAP MODEL HA4522 Holding Cabinet HA4522 CABINET NP ASM SYMQTY PART NO. 1 00021L01 (REF ONLY) 1 1 02331T57 (REF ONLY) 2 3 8 04107V119 (REF ONLY) 4 30 PS1819-6 5 8 PS2550-6 20 04107L66 (REF ONLY) 6 7 6 PS1222-6 8 8 04023W 23 (REF ONLY) 9 4 00079X08 (REF ONLY) 10 2 00306V17 (REF ONLY) 11 2 00233M 01 (REF ONLY) 12 4 00244V18 (REF ONLY) 13 1 06255M 04 (REF ONLY) DESCRIPTION BACK INTERIOR BASE ASM BOLT CARRIAGE 1/4-20 x .75* NUT FLANGE LOCK 1/4-20* NUT NYLON INSERT * SCREW 1/4-20 x .750 HEX HD.
WINSTON CVAP MODEL HA4522 Holding Cabinet SY M Q TY 1 1 2 1 3 1 4 4 5 4 6 1 Page 3 of 6 H A 4 5 2 2 E S C /C T R L A S M D E S C R IP T I O N P S 2 2 5 1 , P S 2 6 0 9 ( A - s e r ie s ) , P S 2 7 1 0 ( re w o rk ) C O N T R O L A S M D I F F 1 2 0 V W ELD ED ESCU TCH EO N 2 5 6 1 W 0 2 (R E F O N L Y ) R E F O N L Y - O B S C om ponent S W IT C H P S 1 1 1 9 -6 N U T SPEED S C R E W # 8 x .5 0 4 1 0 7 J 1 0 (R E F O N L Y ) S W IT C H A S M P S2304 Winston Industries, LLC - 2345 Carton Dr.
WINSTON CVAP MODEL HA4522 Holding Cabinet SYM 1 2 3 4 5 6 7 8 9 10 QTY 1 1 4 4 1 1 1 1 4 1 HA4522 Top Interior Motor ASM PART NO. DESCRIPTION COVER TOP INT 00250M03 (REF ONLY) PS2148 FAN 6.25 DIA. PS1819-6 NUT FLANGE LOCK 1/4-20 PS1233-6 NUT HEX 10-32 SEAL SHAFT .312 00283U06 (REF ONLY) SHAFT RETAINER 00276M02 (REF ONLY) TOP INT WELD 00394M02 (REF ONLY) TOP MOTOR INSULATION 00443M01 (REF ONLY) WASHER 01122N01 (REF ONLY) MOTOR ASM PS2051 (120V), PS2100 (240V) Winston Industries, LLC - 2345 Carton Dr.
WINSTON CVAP MODEL HA4522 Holding Cabinet SYM Q TY 1 1 2 1 3 1 4 1 5 6 6 4 7 6 8 4 9 4 10 1 11 1 12 Page 5 of 6 1 H A 4522 D O O R ASM T O P - 03112M 24 D ES C R IPT IO N P AR T N O . D O O R EX TE RIO R 00014M 02 (R EF O N LY ) L IN E R W ELD T OP 00478N 09 (R EF O N L Y) H IN G E D O O R B O TT O M PS2116 L AT C H M A G E N TIC PS1774 G R O M M ET L A R G E PL A STIC PS1263-6 G R O M M E T SC R EW #10 PS1271-6 SC R EW 1/4x .75 TR H D PH PS1241-6 SC R EW 8x .75 TR H D PH PS1118-6 SC R EW 10-32x 1.
WINSTON CVAP MODEL HA4522 Holding Cabinet SY M Q TY 1 1 2 1 3 1 4 1 5 6 6 4 7 6 8 4 9 4 10 1 11 1 12 1 Page 6 of 6 H A 4522 D OO R A SM B O TTO M PA RT NO . D ESC RIPTIO N 00015N03 (R EF O N LY ) D O O R EX T B O TTO M LIN ER W ELD BO TTO M 00478N08 (R EF O N LY ) PS2116 H IN G E D OO R BO TTO M PS1774 LA TC H M A G NETIC PS1263-6 G RO M M ET LA R G E PLA STIC PS1271-6 G RO M M ET SCREW #10 PS1241-6 SCR EW 1/4x .75 TR HD PH PS1118-6 SCR EW 8x .75 TR H D PH PS1788-6 SCR EW 10-32x 1.
Winston Products International, Ltd. CVAP Holding/Proofing Cabinet (Non surface-mounted controls) International Parts Identification Manual Winston Products International, Ltd. Lit.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification Photo Reference .......................................................................................................... 1 - 5 Parts Descriptions & Order Numbers ........................................................................... 6 - 8 How To Use This Manual Use Photo Reference (pages 1 - 5) to identify parts. Match Photo Reference numbers with Parts Descriptions and Order Numbers (pages 6 - 8).
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See page 6 - 8 for Parts Descriptions and Order Numbers 2A (Hidden) 3 1 2B 9 (Hidden) 8 4 (Hidden) 5 7 6 Winston Products International, Ltd.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See page 6 - 8 for Parts Descriptions and Order Numbers 10 (Hidden) 11 12 13 14 Winston Products International, Ltd.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See page 6 - 8 for Parts Descriptions and Order Numbers 18 21 15 20 16 19 17 22 23 22 24 25 27 26 Winston Products International, Ltd.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See page 6 - 8 for Parts Descriptions and Order Numbers 27 26 30 31 28 29 28 32 Winston Products International, Ltd.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See page 6 - 8 for Parts Descriptions and Order Numbers 33 35 34 (Hidden) 36 Winston Products International, Ltd.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification Photo Reference Number Part Description Order Number 1 Door Handle - adapter lexan to chrome Door Handle - Stainless Steel PS2230 PS1774 2A Door Gasket - Top (HA4019 & HA4519) Door Gasket - Top (HA4522) PS1442 PS2151 2B Door Gasket - Bottom (HA4019 & HA4519) Door Gasket - Bottom (HA4522) Door Gasket - (HA4508) PS1446 PS2150 PS1446 3 Door Assembly Ref.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification Photo Reference Number Part Description Order Number 12 Rail Ref.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification Photo Reference Number Part Description Order Number 25 Circulating Fan Motor (120 Volt) Circulating Fan Motor (240 Volt) PS2051 PS2100 26 Transformer (120 Volt) Transformer (240 Volt) PS1644 PS1687 27 Power Board PS1639 28 Wiring Sub Harness with Potentiometer PS1958 29 Differential Control PS2001 30 Air Thermocouple PS1643 31 Water Thermocouple PS1642 32 Varistor (150 Volt) Varistor (275 Volt) PS1234/3 PS1267 33 C
Winston Products International, Ltd. CVAP Holding/Proofing Cabinet (Non surface-mounted controls) International Parts Identification Manual Winston Products International, Ltd. Lit.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification Photo Reference .......................................................................................................... 1 - 5 Parts Descriptions & Order Numbers ........................................................................... 6 - 8 How To Use This Manual Use Photo Reference (pages 1 - 5) to identify parts. Match Photo Reference numbers with Parts Descriptions and Order Numbers (pages 6 - 8).
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See page 6 - 8 for Parts Descriptions and Order Numbers 2A (Hidden) 3 1 2B 9 (Hidden) 8 4 (Hidden) 5 7 6 Winston Products International, Ltd.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See page 6 - 8 for Parts Descriptions and Order Numbers 10 (Hidden) 11 12 13 14 Winston Products International, Ltd.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See page 6 - 8 for Parts Descriptions and Order Numbers 18 21 15 20 16 19 17 22 23 22 24 25 27 26 Winston Products International, Ltd.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See page 6 - 8 for Parts Descriptions and Order Numbers 27 26 30 31 28 29 28 32 Winston Products International, Ltd.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See page 6 - 8 for Parts Descriptions and Order Numbers 33 35 34 (Hidden) 36 Winston Products International, Ltd.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification Photo Reference Number Part Description Order Number 1 Door Handle - adapter lexan to chrome Door Handle - Stainless Steel PS2230 PS1774 2A Door Gasket - Top (HA4019 & HA4519) Door Gasket - Top (HA4522) PS1442 PS2151 2B Door Gasket - Bottom (HA4019 & HA4519) Door Gasket - Bottom (HA4522) Door Gasket - (HA4508) PS1446 PS2150 PS1446 3 Door Assembly Ref.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification Photo Reference Number Part Description Order Number 12 Rail Ref.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification Photo Reference Number Part Description Order Number 25 Circulating Fan Motor (120 Volt) Circulating Fan Motor (240 Volt) PS2051 PS2100 26 Transformer (120 Volt) Transformer (240 Volt) PS1644 PS1687 27 Power Board PS1639 28 Wiring Sub Harness with Potentiometer PS1958 29 Differential Control PS2001 30 Air Thermocouple PS1643 31 Water Thermocouple PS1642 32 Varistor (150 Volt) Varistor (275 Volt) PS1234/3 PS1267 33 C
Winston CVAP® Holding/Proofing Cabinet (Surface-mounted controls) Parts Identification Manual 2345 Carton Drive Louisville, KY 40299 USA (800) 234-5286 (502) 495-5400 To order parts, contact your Winston representative or call the International office: Winston Products Co. (800) 234-5286 USA & Canada/USA TEL: (502) 495-5400/USA FAX: (502) 495-5458 Lit.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification Photo Reference .......................................................................................................... 1 - 5 Parts Descriptions & Order Numbers ........................................................................... 6 - 7 How To Use This Manual Use Photo Reference (pages 1 - 5) to identify parts. Match Photo Reference numbers with Parts Descriptions and Order Numbers (pages 6 - 7).
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See pages 6 - 7 for Parts Descriptions and Order Numbers 2A (Hidden) 3 1 2B 8 (Hidden) 7 4 5 6 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See pages 6 - 7 for Parts Descriptions and Order Numbers 9 (Hidden) 10 11 12 13 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See page 6 - 7 for Parts Descriptions and Order Numbers 16 14 15 17 18 19 (Hidden) 20 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See page 6 - 7 for Parts Descriptions and Order Numbers 12 21 16 14 20 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification NOTE: See page 6 - 7 for Parts Descriptions and Order Numbers 22 23 21 (Hidden) 24 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification Photo Reference Number Part Description Order Number 1 Door Handle - Stainless Steel PS1774 2A Door Gasket - Top (HA4019 & HA4519) Door Gasket - Top (HA4522) PS1442 PS2151 2B Door Gasket - Bottom (HA4019 & HA4519) Door Gasket - Bottom (HA4522) Door Gasket - (HA4508) PS1446 PS2150 PS1446 3 Door Assembly Ref.
WINSTON CVAP BRAND HOLDING/PROOFING CABINET Parts Identification Photo Reference Number Part Description Order Number 13 Air Heater (120 Volt) Air Heater (240 Volt) PS2067 PS2099 14 On/Off Switch PS2304 15 Control Knobs PS1250 16 Control Board Assembly (120 Volt) Control Board Assembly (240 Volt) PS2251 PS2252 17 Cooling Fan Blades PS2083 18 Cooling Fans Motor (120 Volt) Cooling Fans Motor (240 Volt) PS2066 PS2098 19 Hi Limit Thermostat PS2199 20 Circulating Fan Motor (120 Volt) Cir
LIT 6529
LIT 6529
Winston CVAP Brand Cook & Hold Cabinet - CA75 Series Parts Identification Manual 2345 Carton Drive Louisville, KY 40299 USA (800) 234-5286 (502) 495-5400 To order parts, contact your Winston representative or call the International office: Winston Products Co. (800) 234-5286 USA & Canada/USA TEL: (502) 495-5400/USA FAX: (502) 495-5458 Lit.
WINSTON CVAP BRAND COOK & HOLD CABINET Table of Contents Photo Reference .......................................................................................................... 1 - 4 Parts Descriptions & Order Numbers ........................................................................... 5 - 6 Wiring Diagram ............................................................................................................ 7 How To Use This Manual Use Photo Reference (pages 1 - 4) to identify parts.
WINSTON CVAP BRAND COOK & HOLD CABINET Parts Identification NOTE: See page 5 - 6 for Parts Descriptions and Order Numbers 2 1 3 5 4 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND COOK & HOLD CABINET Parts Identification NOTE: See page 5 - 6 for Parts Descriptions and Order Numbers 7 6 8 9 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND COOK & HOLD CABINET Parts Identification NOTE: See page 5 - 6 for Parts Descriptions and Order Numbers 12 13 10 11 15 14 16 17 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND COOK & HOLD CABINET Parts Identification NOTE: See page 5 - 6 for Parts Descriptions and Order Numbers 18 20 21 22 19 23 25 24 26 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND COOK & HOLD CABINET Parts Identification Photo Reference Number Part Description Order Number 1 Magnetic Door Latch HPS1774 2 Door Hinge HPS2116 3 Drip Cup HPS2182 4 Wire Retainer HPS2054 5 Caster - 3" Locking (Front) Caster - 3" Non-Locking (Rear) HPS2146 HPS2147 6 Universal Rail HPS2094 7 Shelf Rack Assembly Ref.
WINSTON CVAP BRAND COOK & HOLD CABINET Parts Identification Photo Reference Number Part Description Order Number 16 High Limit Thermostat HPS2199 17 Blower Motor HPS2100 18 Main Board - GM (1 Channel) Main Board - GM (6 Channel) HPS2238 HPS2239 19 Power Board HPS2173 20 Buzzer HPS1586 21 On/Off Switch HPS1529 22 Transformer Board HPS2172 23 Electro-Mechanical Relay HPS1007 24 Water Thermocouple HPS2177 25 Water Heater (208 Volt) Water Heater (240 Volt) HPS2174 HPS2175 26 Dr
Winston CVAP Brand Drawer Cabinet Parts Identification Manual HB35D 2345 Carton Drive Louisville, KY 40299 USA (800) 234-5286 (502) 495-5400 To order parts, contact your Winston representative or call the International office: Winston Products Co. (800) 234-5286 USA & Canada/USA TEL: (502) 495-5400/USA FAX: (502) 495-5458 Lit.
WINSTON CVAP BRAND DRAWER CABINET Table of Contents Photo Reference .......................................................................................................... 1 - 3 Parts Descriptions & Order Numbers ........................................................................... 4 Wiring Diagram ............................................................................................................ 5 How To Use This Manual Use Photo Reference (pages 1 - 3) to identify parts.
WINSTON CVAP BRAND DRAWER CABINET Parts Identification NOTE: See page 4 for Parts Descriptions and Order Numbers 1 2 3 4 5 6 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND DRAWER CABINET Parts Identification NOTE: See page 4 for Parts Descriptions and Order Numbers 7 8 10 9 11 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND DRAWER CABINET Parts Identification NOTE: See page 4 for Parts Descriptions and Order Numbers 12 13 14 15 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND DRAWER CABINET Parts Identification Photo Reference Number Part Description Order Number 1 On/Off Switch Guard HPS1086 2 Power On Lamp HPS1103/3 3 Thermometer HPS1861 4 Drip Cup HPS2182 N/A Drain Cap PS1654 5 Wire Retainer HPS2054 6 Black Thermostat Dials HPS1250 7 Rollers HPS2181/2 8 Air Heater HPS2197 9 On/Off Switch HPS1529 N/A On/Off Switch PS2304 10 Air/Water Thermostat HPS2200 11 Water Heater HPS2198 12 Fan Blade (Plastic) HPS2188 13 Blo
Winston CVAP Brand Shallow 2 & 3 Drawer Cabinet Parts Identification Manual 2345 Carton Drive Louisville, KY 40299 USA (800) 234-5286 (502) 495-5400 To order parts, contact your Winston representative or call the International office: Winston Products Co. (800) 234-5286 USA & Canada/USA TEL: (502) 495-5400/USA FAX: (502) 495-5458 Lit.
WINSTON CVAP BRAND DRAWER CABINET Table of Contents Photo Reference .......................................................................................................... 1 - 3 Parts Descriptions & Order Numbers ........................................................................... 4 Wiring Diagram ............................................................................................................ 5 How To Use This Manual Use Photo Reference (pages 1 - 3) to identify parts.
WINSTON CVAP BRAND DRAWER CABINET Parts Identification NOTE: See page 4 for Parts Descriptions and Order Numbers 1 2 3 4 5 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND DRAWER CABINET Parts Identification NOTE: See page 4 for Parts Descriptions and Order Numbers 6 7 8 9 10 (Hidden) To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND DRAWER CABINET Parts Identification NOTE: See page 4 for Parts Descriptions and Order Numbers 11 12 13 14 15 3 16 To order parts, contact your Winston representative or call the International office: Winston Products Co.
WINSTON CVAP BRAND DRAWER CABINET Parts Identification Photo Reference Number Part Description Order Number 1 On/Off Switch Guard HPS1086 2 Power On Lamp HPS1103/3 3 Thermometer HPS1861 4 Drip Cup HPS2182 5 Black Thermostat Dials HPS1250 6 Roller Assembly HPS2181/2 7 Drawer Rail HPS2227 8 Thermometer & Air Thermostat bulbs Ref.