Wireless AC750 Dual-Band Range Extender Model: WS-WN566A2 Quick Installation Guide (Q.I.G.) REV 1.
Open Source Code This product includes software codes developed by third parties. These software codes are subject to either the GNU General Public License (GPL), Version 2, June 1991 or the GNU Lesser General Public License (LGPL), Version 2.1, February 1999. You can copy, distribute, and/or modify in accordance with the terms and conditions of GPL or LGPL.
Hardwear Overview Power LED LAN LED WAN/LAN LED WiFi/WPS LED WPS Button Mode Selector Reset button LAN Port WAN/LAN Port Default Parameters Default IP: 192.168.10.1 URL: http://ap.setup Login Name: admin Password: admin 2.4G SSID: Wireless-N(2.4G) 5G/AC SSID: Wireless-AC Wireless Key: no LED indicators POWER LAN & LAN/WAN WiFi/WPS ON: The Device is power on OFF: The Device is not receiving electrical power. ON: The Ethernet port is connected. OFF: The Ethernet port is disconnected.
Getting Started Setting up a Wireless Infrastructure Network For a typical wireless setup at home (as shown below), please do the following: Wireless AP Mode The AP/Router is connected to a wired network then transforms the wired Internet access into wireless so that multiple devices can share the Internet. So this mode is fit for office, home and places where only wired network is available.
Configure the Wi-Fi Repeater Mode Configure the Wi-Fi Repeater Mode with WPS Button. This is the easiest way to configure the AP/Router. First, check whether your wireless router supports WPS. For further details, please read the operating instructions for your wireless router. 1. 2. 3. 4. The mode selector must be set to the "AP/Repeater" position for Repeater Mode. Plug the AP/Router into a wall socket. Press the WPS button on the AP/Router for at least 6 seconds.
You can configure the Wi-Fi Repeater Mode by connecting it with your computer/laptop with enclosed RJ45 cable or wirelessly. A. Configure the Wi-Fi Repeater Mode wirelessly. A1. The mode selector must be set to the "AP/Repeater" position for Repeater Mode. Plug the AP/Router into a wall socket. A2.Click on the network icon ( or ) on the right bottom of your desktop. You will find the signal from the Wireless-AC or Wireless-N(2.4G). Click on ‘Connect’ then wait for a few seconds. A3.
A4.The login screen below will appear. Enter the User Name and Password then click “Submit” to login. The default User name is “admin” and Password is “admin”. A5.After logging in, you will see the web page below: Click on the Repeater button in the Wizard.
A6. From the list, select a wireless network with which you want to connect the AP/Router by choosing the corresponding network in the "Select" field. A7. After having selected a wireless network, you must then specify the network key of your wireless router for Security key. After completing the entry, click on the “Apply” button. After the reboot has been completed, the AP/Router is accessible under the SSID and the Wireless key of your wireless router. B.
Configure the Wireless AP Mode. Use the AP Mode to obtain a "wireless access point". The wireless end devices will connect to the AP/Router in this mode. You can also use this mode, for example, to make a formerly non-wireless-enabled router wireless-enabled. 1. 2. 3. 4. The mode selector must be set to the "AP/Repeater" position for AP Mode. Plug the AP/Router into a wall socket. Follow process A2 to A4. After logging in, you will see the web page below: Click on the AP button in the Wizard.
The following message will be displayed on your web browser: SSID Wireless SSID of the AP/Router Security type Setup the wireless security and encryption to prevent from unauthorized access and monitoring. Supports 64/128-bit WEP, WPA, WPA2, WPA/WPA2 encryption methods. Security key The "Password" of the AP/Router Click on ‘Apply’ button, The AP/Router will restart. After the reboot has been completed, the AP/Router is accessible under the SSID and the Wireless key.
Configure the Wireless Router Mode The AP/Router is connected to a DSL or cable modem and works as a regular wireless router. Internet access from DSL or cable modem is available for one user but more users need to share the Internet. 1. The mode selector must be set to the "Router" position for Router Mode. 2. Plug the AP/Router into a wall socket 3. Connect your DSL Modem with the AP/Router with RJ45 Cable 4. Follow process A3 to A4. 5.
Choose your WAN Connection Type. If Dynamic IP is selected, the Router gets the IP address automatically from the DHCP server or the ISP. No configuration should be set and you can go on with the wireless configuration. If ADSL Dial-up (PPPoE) is selected, please enter the User Name and Password from your ISP, These fields are case-sensitive.
If static IP is selected, please enter the IP Address, Subnet Mask, Default Gateway, etc. Set the wireless parameter. It's recommended that you rename an SSID, choose a Security Mode and enter a Key. SSID The "SSID" of the AP/Router Channel Auto (recommend) Security type Setup the wireless security and encryption to prevent from unauthorized access and monitoring. Supports 64/128-bit WEP, WPA, WPA2, WPA/WPA2 encryption methods.
Management via Web Browser Wireless Base Configuration Please follow the following instructions: Click “Wi-Fi -> Basic Settings” located at the web management interface, the following message will be displayed on your web browser: You could configure the basic setting of Wireless settings for communication, such as Network Name (SSID) and Channel. The Access Point can be set simply with only the minimum setting items.
Change Management password Default password of Wireless Repeater is “admin”, and it’s displayed on the login prompt when accessed from web browser. There’s a security risk if you don’t change the default password, since everyone can see it. This is very important when you have wireless function enabled.
Firmware Upgrade The system software used by this router is called ‘firmware’, just like any applications on your computer, when you replace the old application with a new one, your computer will be equipped with new function. You can also use this firmware upgrade function to add new functions to your router, even fix the bugs of this router.
Factory Default and Settings Backup, Restore You can backup all Setting of this router to a file, so you can make several copied of router configuration for security reason.
How to connect your computer/laptop with the AP/Router Adding a Wireless computers to the AP/Router 1. Log on to the computer. 2. Open Connect to a Network by right-clicking the network icon ( or ) in the notification area. 3. Choose the wireless network from the list that appears, and then click Connect. 4. Type the network security key or passphrase if you are asked to do so, and then click OK. You'll see a confirmation message when you are connected to the network. 5.
Adding a Wireless computers to the AP/Router with WPS Button This is the easiest way to establish a connection to the AP. First, check whether your end device supports WPS. For further details, please read the operating instructions for your end device. 1. 2. 3. Log on to the computer. Press the WPS button on the AP/Router for 3 seconds. The WIFI/WPS LED now flashes for approx. 2 minutes. Within these 2 minutes, please press the connection button (WPS) on your end device.
How to configure your computer/laptop with the Network IP Address 1. Log on to the computer. 2. Click the “Start” button (it should be located at the lower-left corner of your screen), then click “Control Panel”. Click “View Network Status and Tasks”, and then click “Manage Network Connections”. Rightclick “Local Area Network”, then select “Properties”. When the “Local Area Connection Properties” window appears, select “Internet Protocol Version 4 (TCP/IPv4)” and then click “Properties”. 3.
Warning: 1: For indoor use only. 2. The main plug is used as disconnect device, the socket-outlet should be near the appliance and it should be easily accessible. 3. This product must not be disposed together with the domestic waste. This product has to be disposed at an authorized place for recycling of electrical and electronic appliances. By collecting and recycling waste, you help save natural resources, and make sure the product is disposed in an environmental friendly and healthy way.
