Installation Guide

ManualsBrandsWINSOON ManualsBarn Door Hardware6 ft./72 in. Stainless Steel Sliding Barn Door Hardware Kit T-Shaped Wheel for Double Door with Non-Routed Floor Guide

Installation Manual

Barn Door Hardware

www.winsoonhardware.com

Track Accessories

Single Door Hardware Kit Includes

Part Name

5FT4FT

6FT 6.6FT7.5FT 8FT 9FT 11FT10FT 12FT 13FT 14FT 15FT 16FT 17FT 18FT

1 1 1 2 2 2 2 2

0 0 0 1 1 1 1 1

2 2 2

2 2 2 2 2 2 22 2 2 2

4 5 6

4 6 6 8 9 10

8 8 10 12

2 2 2

2 2 2 2 2 2 22 2 2 2

2 2 2

2 2 2 2 2 2 22 2 2 2

1 1 1

1 1

1 1 1 11 1 1

1 1 1

1 1

1 1 1 11 1 1

picture

Junction

Tube

Tube Plug

Spacer

Floor

guide

Door

Stopper

Hex

Wrench

Track

Hanger

Double Door Hardware Kit Includes

Part Name

5FT4FT

6FT 6.6FT7.5FT 8FT 9FT 11FT10FT 12FT 13FT 14FT 15FT 16FT 17FT 18FT

1 1 1 2 2 2 2 2

0 0 0 1 1 1 1 1

4 4

4 5 6

4 6 6 8 9 10

8 8 10 12

2 2 2

2 2 2 2 2 2 22 2 2 2

2 2 2

2 2 2 2 2 2 22 2 2 2

1 1 1

1 1

1 1 1 11 1 1

picture

Junction

Tube

Tube Plug

Spacer

Floor

guide

Door

Stopper

Hex

Wrench

Track

Hanger

Note: If you encounter any problem with the package and the following installa-

tion, please email us at productservicecenter@outlook.com . Please also tell

us your “ORDER ID,” we will solve any issues for you as soon as possible.

● Installation Tools

※ Check the Quantities of Flat Track ,Accessories and Steel

Hanger.

Pencil Level RatchetWrenchRuler

drill

Router

Summary of content (6 pages)

PAGE 1
Track Accessories Single Door Hardware Kit Includes Part Name Barn Door Hardware Installation Manual picture 4FT 5FT 6FT 6.6FT7.
PAGE 2
Prepare Your Doors Chart: Track Junction 4.3” 19.7” 4FT 10.3” 19.7” 5FT 3.45”19.7” 5.5FT 6.45” 19.7” 6FT 10.05” 19.7” ● Steel Hanger 19.7” 4.3” Tip: Different Steel Hanger styles match with different Door Stoppers. Please identify the matching Hanger and Stopper you bought. 19.7” 10.3” 19.7” 19.7” 3.45” 19.7” 19.7” 6.45” 19.7” 19.7” 10.05” 6.6FT 7.5FT 8FT 9FT 10FT 5.6” 19.7” 19.7” 4.3” 19.7” 19.7” 4.3”4.3” 19.7” 4.3” 19.7” 19.7” 4.3”10.3” 19.7” 10.3” 19.7” 3.45”19.
PAGE 3
※Hardware Installation 2-1/8”(54mm) 5-1/8”(130.75mm) 2-15/16”(74.50mm) Type-a Step 1: Attach Steel Hangers to Your Doors Drill 3/8” (10mm) holes at the position from the top of the doors shown in the above chart. 7/16”(12mm) Type-a 1/4”(6mm) 2-1/4”(57mm) 3-5/16”(84mm) 1-1/8”(30mm) Type-b 2”(50mm) 2-3/4”(70mm) 2 (57 -1/4” mm ) 5/8”(16mm) 5/16”(8mm) 1-1/8”(30mm) Type-b Type-c 7/16”(12mm) 2-1/8”(54mm) 2-1/4”(58mm) 2-3/16”(55.
PAGE 4
Step 2: Cut Floor Guide Slot At The Bottom Of The Door Cut a 5/16” (7mm) wide, 3/4” (20mm) deep slot at the bottom of the door. Recommended: Cut the slot with a router and slot cutter bit. 5/1 6”( Step 4: Install Spacers a.Putting the b-3 into the rail and make the hole direction of b-3, rail and b-2 is consistent. b.Installing in order from inside to outside to prevent missing the hole.
PAGE 5
Step 6:Mark and Drill Track Holes 1.Mark the positions of each set’s two spacer holes, the distance between each hole is shown as the picture. 2.Punch all the marked positions into the wall with impact drill, put the expansion pipes into the holes created, then punch the pipe pins into the wall until the expansion pipes expand at their ends, screw b - 1 into the expansion pipe. 1.1” Step 8: Install Your Doors a.
PAGE 6
Step 9:Install the Floor Guide Position the door at your desired close position, put half of the floor guide under the door, mark the location, and then fix guide to the floor. WARNING • Failure to wear proper safety gear (i.e.,eye protection) may result in serious injury or death. Always wear proper safety gear before using power tools. • Improper operation of power tools may result in loss of control, serious injury or death.