LED CEILING LIGHT ITM. / ART. 1165831 Model: LM56123 CARE & USE INSTRUCTIONS IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY For assistance with assembly or installation, parts and customer service, call us at 1-866-294-9244 (English), Monday - Friday, 8am - 5pm Pacific Time, email us at info@winplususa.com 820 South Wanamaker Ave., Ontario, CA 91761, USA www.winplus.
This LED Ceiling Light is suitable for use in any indoor location (e.g. home, office, warehouse, workshop, garage, and etc.). This light has the following unique features: • Built-in Smart Sensor Control System: This LED Ceiling Light uses a microwave sensor to automatically turn on when motion is detected and will turn off automatically after no movement is detected in the area after the preset (5 min or 30 min) time.
common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. • Do not install this LED with a dimmer. Doing so may damage the driver inside if used with a dimming circuit. • This device does not have a plug; rewiring is required. If you are unsure how to rewire this light, please contact a qualified electrician to install instead of attempting to rewire yourself. • Power will still run to the light even after the LED lifespan runs out.
Before Installation: Carefully remove the light fixture, mounting package, and wireless remote from the box and check that all parts are included. Do not attempt to assemble the product if any part is missing or damaged. The outlet box described in this manual is not provided. A standard outlet box needs to be pre-installed in the ceiling, and the power supply wires need to be run to the outlet box providing 120Vac of power. If an outlet box does not exist, contact a qualified electrician for installation.
4. Carefully place all the wires and wire connections into the outlet box. 5. Place the lamp body over the outlet box and feed the mounting screws through the inner keyhole slots. 6. Rotate the lamp body clockwise so that the mounting screws slide into the narrow ends of the keyhole slots. 7. Tighten the mounting screws to ensure the lamp body is secured against the ceiling. 8. Attach the cover to the lamp body, and rotate the cover counter-clockwise to secure in place.
Wireless Remote: Before use, please open the switch cover on the back of the remote, and insert two AAA batteries. When using the remote, you must point the remote directly to the light, to ensure the signals can be sent to the light. When the light receives the remote signal, the light will blink once so that you will recognize it. Remote Setting: 1 2 4 6 3 5 7 8 1. Motion Sensor You can press the Motion Sensor button to switch ON (green indicator) or OFF (red indicator).
5. Power Button You can press the power button to turn light on and off accordingly. NOTE: When you press power button to turn light off while the Motion Sensor function is set to ON, the light will turn ON automatically again when there is motion detected. 6. Distance Distance is the sensor detection area of the smart sensor. You can choose from various settings: Very near, Near, Mid-range and Far. The sensing distance would be ranged from around 1 m / 3.2 ft to 8 m / 26.2 ft.
Product Specifications: 1. Operating Voltage: 120Vac, 60 Hz 2. Maximum wattage: 22 W 3. Maximum Light Output: 1700 lm 4. Color Temperature: 2700K – 5000K 5. LED Life Cycles: up to 50,000 hrs* 6. CRI: 90 *Note: 50,000-hour lifespan is for the LED only. Lifespan depends on operating temperature, environmental conditions, etc. Troubleshooting: Problem Light does not illuminate. Light does not turn on. Light does not turn on during the day. Fuse blows or circuit breaker trips when light is illuminated.
Warranty: Winplus North America This Winplus product carries a 1 year warranty against defects in workmanship and materials. This product is not guaranteed against wear or breakage due to misuse and/ or abuse. NOTE: Warranty only applies for North American customers of purchases made in North America.
NOTE: Toll Free # is for North America Customers ONLY. See Customer service section for customer contact numbers for other regions/offices. For customer service and technical support, please call us at 1.866.294.9244 or email us at info@winplususa.com. If at that time it is determined that a replacement unit is needed, the support representative will issue a Return Authorization and instruct on how to get a new unit.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. DISTRIBUTED BY: COSTCO WHOLESALE CORPORATION P.O.
