LED INDOOR SHOP LIGHT TM WITH MOTION SENSOR ITM. / ART. Model: LM55973 CARE & USE INSTRUCTIONS IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY For assistance with assembly or installation, parts and customer service, call us at 1-866-294-9244 (English), Monday - Friday, 8am - 5pm Pacific Time, email us at info@winplususa.com 820 South Wanamaker Ave., Ontario, CA 91761, USA www.winplus.
This light is operated by a Smart Sensor Control. It will automatically switch on when motion is detected and will turn off automatically when there is no movement in area for preset time. Important Safety Instructions: Please read the following safety information before use. To reduce risk of fire, electric shock, or injury to persons: • Grounded lights must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances.
Package Contains: Please lay out all parts and read the instructions prior to installation. 1 x LED Indoor Shop Light with 1.5 m / 5 ft power cable NOTE: The product is intended to be connected to a p lug and does not need t o be s witched Measuring Template The default setting for the Smart sensor is set at Very near and the light will dim when no motion is detected within 30 seconds, and will turn OFF when no motion is detected within an additional 699 mm / 27.5 in / 27.
Product Specifications: 1. Input Voltage and Current: 120 Vac, 60 Hz, 4 A max 2. LED Wattage: 48 W / Stand-by mode: 1 W 3. Power Socket: 120 Vac, 3.5 A max 4. Light Output: 3800 lm 5. Color Temperature: 4000K 6. LED Life Cycles: up to 50,000 hrs 7. Weight: 2.23 kg / 4.91 lb 8. Operating temperature: -0°C to 40°C / -4°F to 104°F This product is ETL/cETL Listed Light fixture dimensions: 7 cm / 2.7 in 12 cm / 4.
2 3 2. Wear safety glasses before drilling pilot holes. 4 3. Screw in the screw hooks. 5 4c 4a 4b 4a. Slip the hanging hook through the wire. 5. Clip mounting brackets onto the light. 4b. Insert the hanging hook into the openings of the mounting bracket. Repeat for another mounting bracket. The light is intended to be installed directly beneath a ceiling-mounted receptacle.
Ceiling flush mount: 1 Final installed illustration 2 2. Wear safety glasses before drilling pilot holes. 4 4. Clip mounting brackets onto the light. 6 1. Select a suitable mounting location, and make sure the wooden surface is suitable for supporting the light. Use the measuring template to mark the hook locations on the mounting surface. 3 3. Screw the mounting bracket with the wood screws provided. Repeat for the second mounting bracket.
Ceiling hanging with hooks: 1 Final installed illustration 2 1. Select a suitable mounting location, and make sure the wooden surface is suitable for supporting the light. Use the measuring template to mark the hook locations on the mounting surface. 3 2. Wear safety glasses before drilling pilot holes. 4 3. Screw in the screw hooks. 5 a b 4a. Mount the hanging hook into the screw hook. Repeat for the second hanging hook. 5. Clip mounting brackets onto the light. 4b.
Link up multiple Shop Lights Connect to Power Outlet Connect to another shop light Linkable up to 6 shop lights Smart Sensor Control Setting and Operation: Unplug and allow the unit to cool before changing the control setting. You can use the light in different locations by selecting the Smart Sensor control setting that is most suitable for the desired location and use. Please refer to the following instructions for choosing the Smart Sensor control setting.
Definition of each Smart Sensor Control Setting: Switches 1 & 2: Sensor Detection Distance Setting Very near Maximum Sensing Distance (D) 1 m / 3.2 ft - 1.5 m / 4.9 ft Near 1.5 m / 4.9 ft - 3 m / 9.8 ft Mid-range 3 m / 9.8 ft - 4.5 m / 14.7 ft Far 4.5 m / 14.7 ft - 6 m / 19.6 ft 3 m / 9.8 ft Sensor Detection Distance is the detection area of the smart sensor. You can choose from various settings: Very near, Near, Mid-range and Far. The sensing distance would be ranged from around 1 m / 3.
Switches 5 & 6: Ambient Light Sensor Ambient Light Sensor refers to the surrounding light level to keep lighte OFF during the day time regardless of any movement. You can choose from Off, Overcast, Dusk and Night. For example, if you set to Overcast, when the surrounding is bright enough, such as sunny day, the light will stay OFF even if motion has been detected. When the surrounding area is less bright than overcast and there is motion detected by the sensor, the light will turn ON.
If you have selected Time Dim function ON, the timer will start counting the Time Until Dim function (S3 & S4) and then the Time Until Off (S9 & S10). E.g. for S3 & S4 as 30 sec and S9 & S10 as 5 min: the light will be dimmed down when no motion has been detected for 30 seconds and the light will be turned OFF when no motion is detected within 5 minutes after. Any movement detected within this period will restart the timer, and the light will turn on again.
Always On: 1 & 2 Distance: Far 3 & 4 Time Until Dim: 10 min 5 & 6 Ambient Light Sensor: Off 7 & 8 Brightness Level: 100% 9 & 10 Time Until Off: Off By selecting this mode, the light will be ON all the time. When there is no movement within 10 min, the light will dim down. The light will return to full brightness when there is movement detected.
Troubleshooting: Issue The light is not working Cause Remedy The light is not plugged in or the Main switch is OFF Plug in and turn on the Main switch The ambient light sensor is ON and it switches OFF the light while the ambient is bright.
Warranty: Winplus North America This Winplus product carries a 1 year warranty against defects in workmanship and materials. This product is not guaranteed against wear or breakage due to misuse and/ or abuse. NOTE: Warranty only applies for North American customers of purchases made in North America.
NOTE: Toll Free # is for North America Customers ONLY. See Customer service section for customer contact numbers for other regions/offices. For customer service and technical support, please call us at 1.866.294.9244 or email us at info@winplususa.com. If at that time it is determined that a replacement unit is needed, the support representative will issue a Return Authorization and instruct on how to get a new unit.
the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement.