QuattroPod Quick Start Guide Rev. 1.
Introduction Firstly, thanks for choosing QuattroPod as wireless presentation facility. It integrates powerful dual core SoC and advanced 802.11ac 5G Wi-Fi/Bluetooth (GFSK,п/4-DQPSK, 8DPSK) to provide you a smooth wireless display experience, and it supports almost all devices. Our features not only support ‘’Split Screens Display”, “ Host Control System” but also let cross platform devices throw the contents in APP-independence.
-Through USB 5V(required 1A at least, through adaptors or USB ports of laptops) or -Through POE (Power over Ethernet): Ethernet switch or router needs to support standard POE (Power over Ethernet) function and keep it active. 2. To connect TX with Laptops, to connect HDMI or DP2 ports with proper cables. To connect TX with Smart phones, to connect USB port with proper cable with phone’s connectors such as micro USB, Lighting or USB type C.
QuattroPod Receiver QuattroPod Transmitter Pairing: To pair Quattro TX with RX for first time use may be needed. It’s suggested if you are not sure QuattroPod TX has ever paired with the Quattro RX you want to cast. 1. Adjust the switch of the side to right . Plug Quattro TX’s USB cable onto Quattro RX’s USB port in the rear. 2. The Main LED and Side LED will start blinking while pairing, after pairing is done, the Rx’s main LED will turn to White and Tx LED will stop blinking. 3.
Finger Tips Before understanding the status of our Quattro, let us introduce the definition of the LED Lights. There are 2 LED indicators on Quattro RX upside surface. One is in central named Main Button. The smaller button named Side Button. Main Button indicated the projection status.
LED Status list Activate Host without source input Activate Guest without source input Activate Host & in projecting Host received request of projection Guest standby without projecting Host standby without projecting Guest send request of projection and wait for allow 1. Under connection 2. Pairing/TX OTA 3.
Function & Link Status* Outbound link can select only one of Wi-Fi and RJ45 wire line (LAN). Airplay activated after web setting. (Default is off) Quattro RX has been powered on, however, there is neither Quattro TX nor device linked. Shift in 3, which means “under pairing” or “building the connection”. Complete pairing or connection, the number showed total Quattro TX or Device linked. RJ45 wire line disconnected. Shift in 3, which means “building the connection”.
1.1 Direct link- you can apply notebook or mobile phone to search Quattro RX by wifi and key in relative SSID and Password. Turn on web browser and enter “192.168.168.1” in the address bar. 1.2 Through Wifi AP or Routers- if your Quattro RX has been connected to a certain networking device, you can apply notebook or mobile phone to connect the same device. Turn on web browser and enter the address show in mainpage in the Quattro Rx IP shown below.
- to indicate menu icon. - to indicate log-in icon. 2. Log inPress the on the right up corner to log in.
3. Start to set up 3.1 Click the menu button on the left up corner and there are drawer show 3 setting functions. They are Device Management, Network Management, and Admin Setting, and About which indicates device version, IP addresses and wifi frequency..etc. 4. Device ManagementThis section helps to manage user interface language, output resolutions, Max connection and QuattroPod Receiver & Transmitter pairing file download.
4.1 Language- click it and choose the language you prefer to show in the webpage.
4.2 Resolution- 4.3 Max Connection- to set the maximum users of the Receiver. Default is 20 users.
4.4 Pair File Download- down load the pairing file from here and copy to USB drive. Plug in Transmitter for pairing* when the Receiver has been installed on the ceiling or wherever difficult to plug directly. The switch of USB on Transmitter shall be adjusted to “mobile”.
5. Network Management- mainly provide outbound Wi-Fi setting. 5.1 Scan 5G SSID and Connect- this function can help you to scan available Wi-Fi AP and join.
5.2 Remember Wi-Fi- it to provide options to remember the AP setting parameter or not. 6.
6.1 Wi-Fi Channel- to select the channel between QuattroPod Receiver & Transmitter to adjust the performance. 6.2 LAN IP Setting- to configure the wire line connection through LAN cable. *we can support only one connection, either LAN or Wi-Fi at one time.
6.3 SSID- to set the SSID indication of the Receiver on the main screen.
6.4 users can change password of the Receiver, or hide the password to avoid connections without authorization. 6.5 My Screen- Users can replace the theme of the main page of Receiver by uploading graphic or photos.
6.6 Host Control- it can be selected the mode of cast request. Auto Allow means the new request will be cast on screen directly. Share screen will present in screen split when it was on. If set it off, the new casting will be full screen mode. 6.7 Airplay- to turn on/off the iOS /Mac devices can cast without QuattroPod Transmitters. 6.8 Change Admin Password- to change the web setting’s log in password.
6.9 Screen Saving- to configure the screen off when the input is idle for certain time. 6.
6.11 Reboot- to reboot the equipment. 7. About- showing the information of the Receiver. . Frequent Applications & Operation 1. Host has projected on screen, and quest required sharing the screen. Host allows.
2. Host has projected on screen, Host rejects Guest’s screen share request. Indicator 1 Indicator 2 Indicator 3 Result of screen Host Double Click Host Guest Click 3. From share screen mode, Host allows Guest full screen request. Indicator 1 Indicator 2 Indicator 3 Result of screen Host Click Guest GUEST Long Press 4. Guest full screen mode, Host retrieves share screen request.
5. Guest full/share screen mode, Host retrieves full screen request. Indicator 1 Indicator 2 Indicator 3 Result of screen Host Long Press Host Guest © 2017 Actions Microelectronics Co., Ltd. All right reserved. Quattro Pod or Quattro are trademarks of Actions Microelectronic Co., Ltd., registered in China and other countries. Other product and company names mentioned herein may be trademarks other respective companies. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules.
