TABLE OF CONTENTS 1 – INTRODUCTION About this Manual ............................................................................................................................ 1-1 Safety Messages Used in this Manual .............................................................................................. 1-1 Pre-Delivery Inspection .................................................................................................................... 1-2 Front Axle Tire Alignment ........................
Table Of Contents Hazard Warning Flashers .................................................................................................................. 3-3 Mirrors – Power Sideview Exterior .................................................................................................. 3-3 Mirrors – Power Sideview Exterior .................................................................................................. 3-5 Battery Boost Switch ........................................................
Table Of Contents House/Coach Battery Disconnect Switch ......................................................................................... 6-6 Battery Access .................................................................................................................................. 6-6 Battery Care ...................................................................................................................................... 6-7 Circuit Breakers and Fuses – House 12-Volt DC ..............
Roller Shades (Manual) - Solar Day/Night ....................................................................................... 9-9 Wood Furniture and Cabinetry ......................................................................................................... 9-9 10 – SLIDEOUT ROOMS Slideout Room Keylock .................................................................................................................. 10-1 Slideout Room Operation – Electric ..........................................
Power Roof Ventilator .................................................................................................................... 12-7 Effects of Prolonged Occupancy ....................................................................................................
SECTION 1 – INTRODUCTION ABOUT THIS MANUAL This operator’s manual was prepared to aid you in the proper care and operation of the vehicle and equipment. Please read this manual completely to understand how everything in your coach works before taking it on its “maiden voyage”. In addition, please become familiar with the New Vehicle Limited Warranty. NOTE: This manual describes many features of your motorhome and includes instructions for its safe use.
SECTION 1 – INTRODUCTION WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious personal injury. CAUTION CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate personal injury. NOTICE NOTICE is used to address practices not related to personal injury.
SECTION 1 – INTRODUCTION or go to their website at http://www.safercar.gov or write to: Administrator, NHTSA 1200 New Jersey Avenue S.E. Washington, D.C. 20590 You can also obtain other information about motor vehicle safety from the NHTSA website at http://www.safercar.gov OCCUPANT AND CARGO CARRYING CAPACITY LABEL This label is affixed in the driver’s area next to or near the Vehicle Certification Label.
SECTION 1 – INTRODUCTION VEHICLE CERTIFICATION LABEL This label is affixed to the lower driver side armrest panel, driver door, or the driver side door jamb, depending on model. It contains vehicle identification numbers and other important reference information. EXPLANATION OF DATA 1. Chassis manufacturer. 2. Chassis manufacture date. 3. Month and year of manufacture at Winnebago Industries®. 4.
SECTION 1 – INTRODUCTION SPECIFICATIONS AND CAPACITIES 22BR ® Chalet Ford E350 Chassis 24VR Standard Optional Ford® E350 Ford® E450 Chassis Chassis 26QR ® Ford E450 Chassis 31CR ® Ford E450 Chassis 31JR ® Ford E450 Chassis 31RR Ford® E450 Chassis Feature Number 16C 16C 16Y 16Y 16Y 16Y 16Y Length 23' 25' 0.7" 25' 0.7" 27' 11.3" 31' 8.4" 32' 0.2" 32' 0.4" Exterior Height 1 Exterior Width 2 Exterior Storage 3 10' 10" 11' 11' 1" 11' 2" 11' 2" 11' 1" 11' 1" 8' 5.5" 8' 5.
SECTION 1 – INTRODUCTION OWNER AND VEHICLE INFORMATION OWNER INFO Owner’s Name(s) __________________________________________________________________ Address __________________________________________________________________________ __________________________________________________________________________ VEHICLE INFORMATION Motorhome Model Number __________________________________________________________ Motorhome Serial Number ___________________________________________________________ Chassis Vehicle I
SECTION 2 – SAFETY AND PRECAUTIONS • • • • • • • • • Only seats equipped with seat belts are to be occupied while the vehicle is moving. Make sure all passengers have seat belts fastened. Lap belts should fit low on the hips and upper thighs. The shoulder belt should be positioned snug over the shoulder. For pregnant women: Never place the shoulder belt behind your back or under your arm. Adjust the lap belt across your hips/ pelvis, and below your belly.
SECTION 2 – SAFETY AND PRECAUTIONS WARNING Propane gas containers, gasoline, or other flammable liquids shall not be placed or stored onboard the vehicle because a fire or explosion may result. Propane gas containers are equipped with safety valves, which relieve excessive pressure by discharging gas to the atmosphere. Failure to comply could result in death or serious injury.
SECTION 2 – SAFETY AND PRECAUTIONS PROPANE GAS LEAK DETECTOR Your coach is equipped with a Propane Gas Leak Detector, similar to the one shown below. The leak detector sounds an alarm if an unsafe amount of propane gas is present inside the coach. battery during storage periods when the house battery will not be charged regularly by the engine or shoreline. Further Information See the manufacturer’s user guide provided in your InfoCase for further instructions.
SECTION 2 – SAFETY AND PRECAUTIONS a 9-volt battery and has a sensor that is designed to detect toxic carbon monoxide gas fumes resulting from incomplete combustion of fuel. It will detect CO gas from any combustion source such as the furnace, gas range/oven, water heater, refrigerator, chassis engine, and electric generator engine. SMOKE ALARM Your coach is equipped with a Smoke Alarm (located on the ceiling in the lounge area.
SECTION 2 – SAFETY AND PRECAUTIONS FIRE EXTINGUISHER ELECTRICAL A dry chemical Fire Extinguisher is located near the main entrance door. • • Fire Extinguisher (Typical installation - your coach may vary according to model and floorplan) We recommend that you become thoroughly familiar with the operating instructions displayed on the side of the Fire Extinguisher and in the information supplied in your InfoCase.
SECTION 2 – SAFETY AND PRECAUTIONS MAINTENANCE • • • • Do not remove the radiator cap while engine and radiator are still hot. Always check coolant level visually at the see-through coolant reservoir. Never get beneath a vehicle that is held up by a jack only. Do not mix different construction types of tires on the vehicle, such as radial, bias, or belted tires, as vehicle handling may be affected. Replace tires with exact size, type, and load range.
SECTION 2 – SAFETY AND PRECAUTIONS place, the cord can be replaced using a blunt instrument, preferably one made of plastic. We recommend you contact your dealer for assistance. POWER SOFAS AND BEDS WARNING Keep people away from operating mechanism and pinch hazard areas during use. Failure to do so could cause injury. SLIDEOUT ROOMS WARNING Your motorhome may have more than one slideout room. Understand which switch operates which slideout room prior to operation.
SECTION 2 – SAFETY AND PRECAUTIONS MOLD, MOISTURE, AND YOUR MOTOR HOME What is Mold? Molds are part of the natural environment. They are as old as the Earth itself and mold spores are almost everywhere at some level waiting to grow. Mold plays a part of nature by breaking down dead organic matter, such as fallen leaves and dead trees. Indoors however, mold growth should be avoided. Molds reproduce by means of tiny spores.
SECTION 2 – SAFETY AND PRECAUTIONS The ladder on your motorhome is provided for limited access to the roof. Walking or working on the roof should be left to qualified service personnel using proper safety equipment in a safe environment. You should only walk or work on the roof if you are qualified and have created a safe environment. For your safety, it is not recommended that you store or carry items on the roof. Before Using the Ladder • • • Inspect the ladder to make sure it is not damaged.
SECTION 2 – SAFETY AND PRECAUTIONS Check your tires for proper inflation before each trip and at least once a month with an accurate tire gauge. Spare Tire Storage If your coach is supplied with a spare tire, it may be fastened to the backwall of the coach or inside a rear storage compartment. Some models, however, may have a swingdown spare tire carrier beneath the rear of the coach. Please follow all safety warnings and instructions for removing spare tire from the carrier.
SECTION 2 – SAFETY AND PRECAUTIONS NOTICE Operating a vehicle under a severe overheating condition can result in damage to the vehicle. For information on what to do in case of overheating, consult your chassis manual.
SECTION 3 – DRIVING YOUR MOTOR HOME The information in this section refers only to features installed or adapted to the dash and driver compartment area by Winnebago Industries®. It also includes passenger seating in the living area of the coach. Further Information See the chassis manual in your InfoCase for all original chassis related controls, instrumentation, switches, and other features.
SECTION 3 – DRIVING YOUR MOTOR HOME one person use the same safety belt at any one time, and do not let the safety belts become damaged by pinching them in the doors or in the seat mechanism. After any serious accident, any seat belts which were in use at the time must be inspected and replaced if necessary. Lap/Shoulder Belts See your chassis manual for instructions on proper fastening, adjustment, and releasing of lap/shoulder belts.
SECTION 3 – DRIVING YOUR MOTOR HOME 3. Be certain that it is appropriate for the child's height, weight, and development. The instructions and/or the regulation label attached to the restraint typically provides this information. 4. Review the instructions for installation and use of the restraint. Be sure that you understand them fully and can install the restraint properly and safely in your vehicle.
SECTION 3 – DRIVING YOUR MOTOR HOME Mirror Heat Switch Mirror Adjustment Control • Mirror surface tilts in direction of arrow button pressed. • Middle switch selects L or R mirror to adjust. • Center position is “neutral” to disable arrow buttons and prevent misadjustment of mirrors. Mirror Pivot Lock • Unscrew protective cap and loosen Allen head set screw to pivot mirror head. Allen Head Set Screw Turn Signal Indicator Lights • The mirrors can be folded back against the cab doors, if needed.
SECTION 3 – DRIVING YOUR MOTOR HOME MIRRORS – POWER SIDEVIEW EXTERIOR –If Equipped Always adjust mirrors for maximum rear visibility before traveling. Make sure the seat is adjusted for proper vehicle control and that you are sitting back squarely into the seat. The mirrors may also contain heating elements to de-fog or de-ice the mirror glass during cold weather operation. An ON-OFF switch for the mirror heaters is located near the remote mirror controls.
SECTION 3 – DRIVING YOUR MOTOR HOME NOTE: The dash air conditioner is not designed to cool the entire interior of the coach, but is intended only to provide cooling for the cab area. RADIO IN-DASH/REARVIEW MONITOR SYSTEM –If Equipped The radio in your coach can receive AM/FM stereo and weather band stations. It also has a compact disc (CD) player for your listening enjoyment through quality high-output speakers located in several areas of the coach.
SECTION 3 – DRIVING YOUR MOTOR HOME iPod Cable -Typical View See the manufacturer’s information in your InfoCase for operating instructions. Radio Remote Control A hand-held remote control for the radio lets you change radio stations or CD selections from a distance for your convenience. The remote control is included in your InfoCase.
SECTION 3 – DRIVING YOUR MOTOR HOME Satellite Radio –If Equipped Your coach may be equipped with a Sirius® satellite radio receiver that plays through your radio. See the receiver manufacturer’s information in your InfoCase for programming and operating instructions. by house batteries. If the House/Coach Battery Disconnect switch is OFF, the speakers will not emit sound. iPod Cable -If Equipped Your coach may be equipped with a cable to connect your iPod to play through your dash radio.
SECTION 3 – DRIVING YOUR MOTOR HOME WARNING Make sure all replacement tires are of the same size and rating as those shown on your Vehicle Certification Label. SUSPENSION ALIGNMENT AND TIRE BALANCE Front Engine Latches -Typical View ENGINE COOLING SYSTEM Do not remove the radiator cap while engine and radiator are still hot. Always check coolant level visually at the see-through coolant reservoir.
SECTION 3 – DRIVING YOUR MOTOR HOME AIR SPRINGS – REAR HELPER (AIR BAGS) –If Equipped The rear air helper springs (air bags) are an enhancement to the standard suspension system to provide adjustable load and ride conditions. This feature is not intended to increase the load capacity of the rear axle or vehicle. Adjustment Check and adjust the air bag pressure periodically to maintain optimal ride and handling characteristics according to cargo weight.
SECTION 4 – APPLIANCES AND SYSTEMS The appliances installed in your motorhome are manufactured by reputable RV appliance makers and have been tested by independent laboratories to meet all applicable standards and codes set for RV appliances. See Section 2 - Safety and Precautions of this manual for any safety and precautions you need to take regarding the operation of your appliances.
SECTION 4 – APPLIANCES AND SYSTEMS To Open 1. Use a screwdriver or coin to turn the latch knobs to the vertical position as shown. • • • • • Gas- Refrigerator will operate on gas from the propane tank if the main valve is open and the tank contains gas. Auto- Refrigerator will operate on 120-VAC household current if the shoreline is connected or the auxiliary generator is running. If electricity is lost, it will automatically switch over to Gas operation if gas is available.
SECTION 4 – APPLIANCES AND SYSTEMS WARNING IT IS NOT SAFE TO USE COOKING APPLIANCES FOR COMFORT HEATING Cooking appliances need fresh air for safe operation. Before operation: 1. Open overhead vent or turn on exhaust fan. 2. Open window. To Light Range Top Burners • Turn the desired burner knob counter-clockwise to the ON or LITE position (do NOT attempt to light more than one burner at a time). • Turn the SPARK knob clockwise one “click”.
SECTION 4 – APPLIANCES AND SYSTEMS MICROWAVE OVEN -If Equipped Refer to the manufacturer’s user guide located inside the appliance for complete operating instructions. pump and water heater. Indicator lights tell you if the water pump is on or if the water heater pilot light is out. Water And Holding Tank Levels Press and Hold the Levels Test switch to show approximate level on the monitor lights.
SECTION 4 – APPLIANCES AND SYSTEMS Tank Capacities See “Tank Capacities” in Section 1 Introduction. Propane Gas Level Press and Hold the Levels Test switch to show approximate propane tank level. The propane level is registered by a sending unit on the tank. The gauge mounted on the side of the tank will give a more accurate indication of actual tank level if needed. Battery Charge Meter Press and Hold the Levels Test switch to check the level of charge (voltage) in the 12-volt house battery.
SECTION 4 – APPLIANCES AND SYSTEMS Further Information Read the operating and safety information provided in the Water Heater Operation Manual in your InfoCase. WATER HEATER - GAS/ ELECTRIC Gas Water Heater Switch (Located on Systems Monitor Panel) For Electric Operation Turn on the Water Heater electric element switch. The shoreline must be connected or generator running for electric operation. -If Equipped (with Motoraid water heating system) The gas/electric water heater has a dual power feature.
SECTION 4 – APPLIANCES AND SYSTEMS Further Information Read the operating and safety information provided in the Water Heater Operation Manual in your InfoCase. PRESSURE-TEMPERATURE RELIEF VALVE Gas Water Heater Switch (Located on Systems Monitor Panel) On occasion, water may be seen seeping from the water heater pressure temperature relief valve. This is no cause for repair or replacement of the valve. For Electric Operation Turn on the Water Heater electric element switch.
SECTION 4 – APPLIANCES AND SYSTEMS 2. Open a faucet in the motorhome to relieve water pressure. 3. Pull the handle of the P-T valve straight out and allow water to flow until it stops. •Lift handle straight out to open P-T valve when water heater is cold 4. Let the handle of the P-T valve snap shut. 5. Close the faucet and turn on the water supply before switching the water heater on. Manually operate the pressure temperature relief valve at least once a year.
SECTION 4 – APPLIANCES AND SYSTEMS To Shut Down • • Move Thermostat switch to OFF position. Close Propane Gas Tank valve if coach will be stored for a period of time. Further Information Refer to the manufacturer’s user guide provided in your InfoCase for further information, including operating precautions and periodic maintenance. See the Coach Maintenance Schedule for recommended intervals. PROPANE GAS FURNACE To Start Up 1. Open the LP gas tank valve by turning fully counter-clockwise.
SECTION 4 – APPLIANCES AND SYSTEMS NOTE: The ducted roof air conditioning system has ceiling registers that can be closed if necessary to force more cool air toward a specific area of the coach or to route cool air away from a specific area. If too many vents are closed, however, it can cause the air conditioner unit to shut down, particularly in high humidity conditions. Further Information Refer to the manufacturer’s user guide provided in your InfoCase for complete operating instructions.
SECTION 5 – PROPANE GAS PROPANE GAS SUPPLY The propane gas system supplies fuel for the gas range/oven, water heater, furnace, and refrigerator (while in gas mode). When used and handled properly, this system is safe and economical and provides modern living conveniences wherever you travel. See Section 2 - Safety and Precautions in this manual for other safety and precautions you need to be aware of related to propane.
SECTION 5 – PROPANE GAS DAN G E R DO NOT FILL CONTAINER TO MORE THAN 80 PERCENT OF CAPACITY. FAILURE TO COMPLY COULD RESULT IN A FIRE OR PERSONAL INJURY. Make sure the motorhome is level when filling. It is possible to accidentally overfill the tank if the vehicle is not level, with the fill valve on the uphill side. Overfilling the propane gas tank can result in uncontrolled gas flow, which can cause fire or explosion.
SECTION 5 – PROPANE GAS • • • • • • • • • Exercise caution at all times. Be familiar with the distinctive odor of propane gas. If a leak is suspected, turn off the supply valve immediately. Have the propane gas system checked by your dealer or other qualified propane gas service center. Do not tamper with the propane gas piping system, pressure regulator, or gas appliances.
SECTION 5 – PROPANE GAS WARNING Propane cylinders shall not be placed or stored inside the vehicle. Propane cylinders are equipped with safety devices that relieve pressure by discharging propane to the atmosphere. Failure to comply could result in death or serious injury. • • • Never use an open flame to test for propane gas leaks. Replace all protective covers and caps on propane system after filling. Make sure valve is closed and door latched securely.
SECTION 5 – PROPANE GAS Regulator Freeze-up Regulator freeze-ups are caused by the presence of moisture in fuel. This moisture will pass through the cylinder valve and into the regulator where it can freeze. Fuel producers, tank and bottle manufacturers, and propane gas dealers take every precaution to reduce moisture, but sometimes only a fraction of an ounce entering the tank can cause problems.
SECTION 6 – ELECTRICAL ELECTRICAL CAUTIONS • • • • • • Careless handling of electrical components can be fatal. Never touch or use electrical components or appliances while feet are bare, while hands are wet, or while standing in water or on wet ground. Improper grounding of the vehicle can cause personal injury. Do not plug the utility power cord into an outlet which is not grounded and do not adapt the plug to connect to a receptacle for which it is not designed.
SECTION 6 – ELECTRICAL 30 Amp Receptacle The power cord is designed to ground the electrical system through the receptacle. It is also designed to carry the amperage output of most campground outlets. If the electrical receptacle to be used is designed to mate with the prongs of the power cord plug, the electrical connection can be expected to carry rated load.
SECTION 6 – ELECTRICAL 120-Volt Circuit Breakers 12-Volt House Fuses Power Center (Converter) -Typical View Certain circuits, however, remain unchanged for use by items which require 120-volt current, such as the air conditioner(s), the refrigerator in AC mode, the microwave oven, etc. NOTE: The converter will not change 12-volt DC current to 120-volt AC.
SECTION 6 – ELECTRICAL “Off” and back to “On”. If the breaker is continually tripped and no overload is evident, have the system checked for a short in the wiring or the appliances. If the GFCI keeps tripping, have the electrical system checked and repaired, if necessary, before using again. •Push to Reset circuit after monthly testing or ground fault tripping. •Push to Test at least monthly. Should break circuit. Press Reset button to reconnect.
SECTION 6 – ELECTRICAL To use the 120-volt generator, plug the power cord into the generator receptacle within the utility compartment before starting the generator. Refer to the hourmeter to determine when periodic maintenance is due and to record services which have been performed. Operation Warnings and Cautions WARNING Generator Receptacle Power Cord WARNING Do not plug the power cord into the generator receptacle while the generator is running. Electrical shock can cause personal injury.
SECTION 6 – ELECTRICAL Converter See “Power Center.” Chassis Battery The chassis battery is used to operate the engine starter and automotive accessories and controls found on the instrument panel. The slideout room systems and the electric step are also connected to the chassis battery. See your chassis manual for further information on chassis batteries and chassis electrical system. Always leave this switch ON while using the coach.
SECTION 6 – ELECTRICAL Lift UP to release slide tray 3. Slide battery tray out. energy is removed from the battery, it should be replaced by the engine alternator or the coach converter system. If a battery sits unused for 30 days or more, especially during warm weather, it can develop a deposit of sulfate crystals on the metal plates inside the battery. This condition is called “sulfating” and prevents the battery from either releasing or accepting a charge.
SECTION 6 – ELECTRICAL To ensure that the battery will always accept and hold a charge, follow these simple maintenance practices: • Make sure the batteries always remain securely clamped in the battery tray. • Make sure battery cable clamps are tight on the terminal posts and are free of corrosion. • Neutralize corrosion buildup or acid film on top of battery by washing with a baking soda/ water solution. Rinse with clear water.
SECTION 6 – ELECTRICAL House 12-Volt Fuses (Located on the right-hand side of the power converter) -Typical View Automotive Chassis and House 12-Volt Circuit Breakers (Located inside passenger compartment) -Typical View The fuse panel accepts only blade type plug-in fuses. Always replace fuses with those of the same amperage rating. 30 30 Functional Non-Functional Battery Charge Meter See related item under “Systems Monitor Panel” in Section 4 - Appliances.
SECTION 7 – PLUMBING FRESH WATER SYSTEM Water Pressure Regulators Because city water pressure varies from location to location, we recommend obtaining an in-line water pressure regulator to prevent damage to any components, connections, and seals in your fresh water system. These devices simply connect in-line between the supply hose and the city water input on the coach. We recommend regulators that control water pressure to 50 psi. max.
SECTION 7 – PLUMBING NOTE: Always keep the tank fill valve in Normal position unless you are filling the tank. If this valve is left in the Tank Fill position while using the city water, water will keep flowing into the tank and out the tank vent tube onto the ground and the water pump will run without delivering water to faucets. Disconnecting from City Water 1. Turn the city water source OFF. 2. Open a faucet on the coach (such as the exterior wash station, if equipped) to relieve line pressure. 3.
SECTION 7 – PLUMBING 2. 3. 4. 5. 6. Turn water pump switch to “OFF” position. Fill water tank. Open all faucets, hot and cold. Turn on water pump switch. Close each faucet as it begins to deliver a steady stream of water (close cold water first). Leave hot water faucets on until they also deliver a steady stream of water. This will ensure that the water heater is filled with water. 7. Check to be sure pump stops soon after all faucets have been closed. 8. Pump is now ready for automatic operation.
SECTION 7 – PLUMBING open for some time to flush the water heater with clean water. You may also want to turn the water heater off until this is done to avoid wasting energy trying to heat “unused” water). 7. Water system is now disinfected. Continuous Tank Disinfection (Superchlorination) Some RVers like to ensure continuous sanitation of their fresh water tank by “superchlorination”– maintaining an effective low level of chlorine in the tank at all times.
SECTION 7 – PLUMBING • • the holding tank. Toilet tissue made specifically for use in RV toilets and holding tanks is available at most RV supply centers. Don’t dispose of sanitary napkins or other non-dissolving items in the toilet. Don’t put automotive antifreeze or caustic chemicals, such as laundry bleach or heavy detergents into the toilet or holding tank. These products may damage plastic or rubber parts in the system.
SECTION 7 – PLUMBING Sewage Drain Outlet/Dust Cap 7. Rinse sewage drain hose thoroughly with water and stow. NOTE: We recommend that you dump all holding tanks before traveling to avoid carrying unnecessary weight. Using On-Site Sewer Hook-Ups The sewage drain hose may remain attached to the dump outlet and be routed out the bottom of the compartment while the motorhome is parked and connected to an on-site sewage hook-up.
SECTION 7 – PLUMBING water holding tank contains the waste water from the galley sink, shower, and may include bathroom lavatory. See “Specifications” in Section 1– Introduction for tank capacities for your model. Waste Pump The 12-volt Waste Pump disposes gray holding tank waste through a small diameter sewer hose, which is then drained through the main sewage drain outlet. 2. Remove dust cap from sewage drain outlet and connect sewage drain hose. Be sure it is firmly attached.
SECTION 7 – PLUMBING sewage back-up into gray tank. Gray water also rinses any black water solids from the sewage drain hose. 5. Open the Gray Waste Tank Drain valve (located beneath driver side of coach ahead of rear wheel) and press and hold the Waste Pump switch (located near the exterior shower.) Release the Waste Pump switch and close the Gray Waste Tank Drain valve as soon as the gray tank is empty. NOTE: Sound of Waste Pump will change significantly when tank is empty.
SECTION 7 – PLUMBING Holding Tank Level Indicators See “Systems Monitor Panel” in Section 4– Appliances for further information on the monitor panel and checking tank levels. See “Specifications” in Section 1– Introduction for tank capacities for your model. HOLDING TANK HEATER –If Equipped Your coach may be equipped with black water and gray water holding tank heaters to allow use of waste utilities in freezing temperatures. The holding tank heater power switch is located near the monitor panel.
SECTION 7 – PLUMBING Normal Flow Water Tank Drain Valve (Typical) By-Pass Mode CAUTION Leave bypass valve handle in NORMAL FLOW position if draining water and blowing out waterlines. Place in BYPASS position ONLY when using antifreeze solution in waterlines. WINTERIZING PROCEDURE You can winterize the water and plumbing system of your coach using one of the following two methods – 1) Blow out waterlines using compressed air or – 2) Fill waterlines with RV water system antifreeze.
SECTION 7 – PLUMBING left in the shower line. Also place the tip of your finger into the city water inlet and gently press the backflow valve button in the center of the inlet to drain any water trapped in the inlet line. • Also, open the Pressure-Temperature Relief valve at the top right portion of the tank to prevent air locking in the tank while draining.
SECTION 7 – PLUMBING 8. Let air flow for five minutes until water is completely drained out of faucets and drain valves. Then close faucets one at a time. 9. Drain Toilet. Operate and hold toilet flush lever until water is completely drained from toilet. 10. Turn air pressure off. Disconnect water purge adapters. Recap the city water inlet to avoid contamination by dirt or insects. After Disconnecting Air Pressure 11.
SECTION 7 – PLUMBING WARNING NEVER use automotive antifreeze/ coolant in your RV water system. Auto antifreeze contains ethylene glycol which, if ingested, can cause blindness and can be fatal. Set Up Winterization Valves 1. Turn Water Heater Bypass valve to BYPASS position. (See “Water System Drain Valve Locations” chart at the end of this section for location of bypass valve on your model). 2.
SECTION 7 – PLUMBING and prevent entry and contamination by airborne debris, insects, and rodents. Your drainage and fresh water systems are now winterized. See instructions for removal from storage in Section 11 - Maintenance and Storage. Water Heater Drain Plug (Remove with socket) • Open the Pressure-Temperature Relief valve at the top right portion of the tank to prevent air locking in the tank while draining.
SECTION 7 – PLUMBING WATER SYSTEM DRAIN VALVE LOCATIONS MODEL 24VR SYSTEM Waterlines Water Tank • Water Heater • Water Heater Bypass Valve Winterization (Antifreeze) Valve Waterlines • DRAIN VALVE LOCATIONS Two (2) valves beneath shower. Access through removable panel on lower front of shower cabinet. Two (2) valves beneath the bed. Lift mattress to expose access hole.
SECTION 7 – PLUMBING 31CR 31JR 7-16 Waterlines • Water Tank • Water Heater • Water Heater Bypass Valve Winterization (Antifreeze) Valve Waterlines • Three (3) valves under galley sink. Remove bottom drawer to access. Also, place the tip of your finger inside the city water connection and gently press the backflow valve (small “button” in center of connector) to drain any water left in the city waterline. One (1) valve beneath the bed. Lift mattress to expose access hole.
SECTION 7 – PLUMBING 31RR 22BR Waterlines • Water Tank • Water Heater • Water Heater Bypass Valve Winterization (Antifreeze) Valve Waterlines • Two (2) valves beneath the bed. Lift mattress to expose access hole. Also, place the tip of your finger inside the city water connection and gently press the backflow valve (small “button” in center of connector) to drain any water left in the city waterline. One (1) valve beneath the bed. Lift mattress to expose access hole.
SECTION 8 – ENTERTAINMENT VIDEO SELECTION SYSTEM –If Equipped The Video Selection System allows you to switch the antenna, AUX/VCR, cable TV, satellite TV, or DVD signal to any TV set location in the coach. This means one person can watch a program coming in on the roof antenna on the bedroom TV while another person watches a satellite or cable TV program or video on the front TV.
SECTION 8 – ENTERTAINMENT TV – (SWING-OUT) –If Equipped (Typical View - your coach may vary in appearance according to floorplan) Your coach may be equipped with a TV swivel/telescoping mechanism, which allows you to angle the TV to best suit your viewing needs. To Swivel TV 1. Pull the black strap (located on back side of TV) straight DOWN to release the TV from the mounting bracket.
SECTION 8 – ENTERTAINMENT TV/DVD MASTER POWER SWITCH (12-VOLT) (Swing-Out TV) –If Equipped The TV and DVD player unit on models with the swing-out TV are powered by 12-volt coach current and have a master power input switch located on the underside of a side overhead cabinet or on a wall near the TV. Turn off the 12V TV/DVD Master Power switch when not using the TV to conserve house battery charge.
SECTION 8 – ENTERTAINMENT • • • Press FUNCTION button on DVD player or remote to set DVD player to TV CABLE. Use TV Menu button to set TV audio output to “Variable Audio Output”. This routes TV stereo sound output through home theater system. > Audio (turn speaker Off) > Setup (change to Variable) Select TV channels and adjust volume with remote for either the TV or DVD. • The TV screen will display the DVD player logo when the correct input is selected.
SECTION 8 – ENTERTAINMENT FLIP-DOWN SCREEN VIDEO PLAYERS (Rear Bunk models only) –If Equipped The flip-down LCD screen DVD Video Players are mounted overhead in each of the bunk beds. POWER AV MENU 12-Volt Master Power • NOTE: To avoid drain on the 12-volt house battery, we recommend turning the master power switch off when Video Players will not be in use.
SECTION 8 – ENTERTAINMENT • Insert the CD label side down (facing you) into the slot on the side of the player. The player will automatically switch to proper mode to play audio or video CD. To Connect Game Systems or Other A/V Components • • • • • Plug the audio and video cables of the game system or component into the audio-video input jacks at the rear underside of the Video Player. Switch the game system or component ON. Press AV button on Video Player to select. VIDEO 1 or VIDEO 2 input.
SECTION 8 – ENTERTAINMENT Operating the Digital Antenna Further Information 1. Turn the Video Selection box ON. See the antenna manufacturer’s user guide provided in your InfoCase for complete operating and maintenance information. TV SIGNAL AMPLIFIER Video Selection Box (Located near entertainment center cabinet) 2. Turn ON the Signal Meter Power switch (located on the side of the Signal Meter).
SECTION 8 – ENTERTAINMENT EXTERIOR CABLE TV - 12V CONNECTION –If Equipped The exterior cable TV/12-volt connection receptacle on your coach provides connection for use of a TV and/or 12-volt device for your outdoor entertainment. Interior Connection for Satellite Dish (Located near entertainment center cabinet) Exterior Cable TV / 12-Volt Connection (Located near entrance door) -Typical View TV DIGITAL SATELLITE SYSTEM WIRING Your coach is pre-wired for installation of a digital satellite TV system.
SECTION 9 – FURNITURE AND SOFTGOODS SLEEPING FACILITIES WARNING WARNING Sleeping facilities are not intended for use while vehicle is in motion. For safety, passengers must use safety belted seating positions while vehicle is in motion. FRONT OVERHEAD BUNK • • • • –If Equipped The overhead front bunk is located above the driver’s compartment. The rear mattress section can be stacked on top of the front section for storage while traveling or when not in use.
SECTION 9 – FURNITURE AND SOFTGOODS •Lower ladder to floor. •Make sure top of ladder is properly engaged onto retainer brackets and ladder is resting firmly on floor before using. Security Latch (Located on front of sofa) - Pull OUT to release • • Lift the front edge of the sofa seat upward and outward from the wall while gently pushing downward on the backrest until the cushions lie flat. The bed is now ready for use.
SECTION 9 – FURNITURE AND SOFTGOODS DINETTE/BED CONVERSION –If Equipped (Typical view – your coach may differ) Security Latch Handle accessible through front sofa opening Dinette to Bed 1. Release the catch on the table leg brace and fold the leg up against the bottom of the table.
SECTION 9 – FURNITURE AND SOFTGOODS 3. Arrange dinette cushions to cover bed area. DINETTE/BED CONVERSION DREAM DINETTE™ –If Equipped (Typical view – your coach may differ) Dinette to Bed 1. Release the lock rod (located on the bottom of the table) by turning the lock rod clockwise. Bed to Dinette 1. Reattach the table onto the wall support and lower the table leg. Wall Support 2. Lift the dinette cushions upward and push table straight down. Table Bracket 2.
SECTION 9 – FURNITURE AND SOFTGOODS 4. Arrange dinette cushions to cover bed area. 3. Place dinette table(s) securely onto the dinette pedestal leg(s). 5. Reverse steps to convert back into dinette. DINETTE CONVERSION –If Equipped (Typical view – your coach may be featured with two dinette tables and pedestal legs, depending on model) Dinette Table Setup 1. Remove the dinette table(s) and pedestal leg(s) from rear wardrobe or galley cabinet, depending on model. 2.
SECTION 9 – FURNITURE AND SOFTGOODS Sofa to Bed 1. Remove seat back cushions and set aside. 3. Rotate the lever lock (located on the bottom right-hand side of the sofa air bed) “clockwise” to release the bottom section of the sofa air bed. 2. Using the pull strap (attached to the back side of the sofa), pull the sofa back out and extend all the way down to the floor. 4. Unfold the bottom section of the sofa air bed and extend all the way down to the floor. 5.
SECTION 9 – FURNITURE AND SOFTGOODS NOTE: The air mattress is plugged into an AC power outlet behind the sofa. It may be necessary to press the “Reset” button on the galley GFCI outlet before operating. 6. Press and Hold the INFLATE button on the hand control to fill the air mattress. 7. Press and Hold the ADJUST button on the hand control to adjust the firmness of your air mattress to the setting that best suits your needs.
SECTION 9 – FURNITURE AND SOFTGOODS NOTE: If using Deflation Valve to deflate air mattress, pressing down on the mattress itself and forcing air out will speed up the deflation process. OR 4. Lift up the bottom section of the sofa bed and bring all the way up. 2. Fold bottom edges on each side of the mattress IN approximately 6 inches (to avoid pinching and obstruction of the mattress). 3. Fold in the bottom section of the air mattress.
SECTION 9 – FURNITURE AND SOFTGOODS 6. Grasp the pull strap and proceed to bring sofa all the way up. Once the sofa is back in original position, replace the sofa back cushions. Further Information For further operating information and care instructions, see the manufacturer’s user guide provided in your InfoCase. Further Information See the air bed manufacturer’s user guide provided in your InfoCase for complete air bed operating instructions, safety precautions, and repair information.
SECTION 9 – FURNITURE AND SOFTGOODS • Cherry is characterized by its red undertones, but may vary in color from white to a deep, rich brown. Cherry is a close-grained wood with fairly uniform texture, revealing pin knots and curly graining. All wood will age with time and the finish will darken. This is especially true for cherry. This is a soughtafter quality in cherry cabinetry, and those who select it expect this evolution.
SECTION 10 – SLIDEOUT ROOMS A Master Slideout Room Keylock is located near the interior slideout control switch(es). This keylock must be turned ON to operate slideout room(s). Master Slideout Room Keylock (Located near interior slideout control switches) SLIDEOUT ROOM OPERATION – ELECTRIC WARNING Your motorhome may have more than one slideout room. Understand which switch operates which slideout room prior to operation.
SECTION 10 – SLIDEOUT ROOMS To Retract Slideout Room WARNING CRUSH HAZARD. Keep people and objects clear of the inside and outside of the slideout room when operating. Failure to comply could result in death or serious injury. Before Retracting! • • • To Extend Slideout Room Before Extending! • Level the coach and set the Parking Brake. • Ensure exterior compartment doors are closed so that they will not interfere with slideout operation.
SECTION 10 – SLIDEOUT ROOMS • • • Press the Slideout Room “RETRACT/IN” switch and hold until the room is fully retracted, then release the switch. To stop retracting the room during operation, release the button. After the room is retracted, deactivate the slideout switch with the Slideout Room Master Keylock.
SECTION 10 – SLIDEOUT ROOMS • • Status LED’s • Motor Direction • Mode Button • (8) - HALL SIGNAL NOT PRESENT. Encoder is not providing a signal. This is usually a wiring problem. (9) - HALL POWER SHORT TO GROUND. Power to encoder has been shorted to ground. This is usually a wiring problem. NOTE: When an error code is present, the slideout control panel needs to be reset. Operating the Extend/Retract switch will reset the slideout control panel.
SECTION 10 – SLIDEOUT ROOMS There are two slideout motors equipped on the end wall of each slideout room. Pull back wipe seal to access motors. Push-In Procedure 1. Pull back wipe seal to access slideout motor. 2. Using a flat-head screwdriver, push bottom of slideout motor UP to disengage (approximately 1/2” from base). Repeat on opposite slideout motor. • Ensure slideout motor is disengaged approximately 1/2” from base. 3.
SECTION 10 – SLIDEOUT ROOMS 5. See your dealer for service of the slideout motors before using again. Further Information Please refer to the slideout manufacturer’s user guide provided in your InfoCase for further instructions and troubleshooting information. GENERAL SLIDEOUT CARE • • • • Keep slideout room seals clean. Clean the floors inside the coach before retracting the slideout room to avoid floor scratches or carpet pile snags.
SECTION 11 – MAINTENANCE AND STORAGE SEALANTS – INSPECTION AND GENERAL INFORMATION NOTE: Proper sealant inspection includes not just visual observation but running a finger along sealant seams to verify proper adhesion to the surface. Any loosened areas must be replaced. • Have the sealant replaced if you notice any of the above. Your local Winnebago Industries dealer has the correct and necessary parts and experience to help you maintain your sealants.
SECTION 11 – MAINTENANCE AND STORAGE weight to the vehicle. This, in effect, reduces the amount of cargo you can carry and remain within GVWR and GAWR limits. Corrosive materials, such as those used for ice and snow removal and dust control, can also accumulate on the underside of a vehicle. These materials should be removed by flushing the undercarriage regularly with water, especially horizontal surfaces, cavities, and other areas where mud and other deposits may collect.
SECTION 11 – MAINTENANCE AND STORAGE Washing • • • • Commercial vehicle wash facilities should be strictly avoided! They will scratch your RV! Truck-style wash centers have highpressure wands that emit higher than necessary water pressures and the brushes are very aggressive. Most truck wash brushes are made from a heavy plastic for durability and are under heavy pressure. They are designed to clean heavy road films on semi trailers and are often dirty.
SECTION 11 – MAINTENANCE AND STORAGE • • Avoid paste waxes. They sometimes have fillers and additives that give a very short term result. Stay away from silicones in polishes and soaps. Buffing compounds remove some of the mil film of the clearcoat, so we recommend that only professionals or very experienced users apply this type of product. Inspection A motorhome exterior is subjected to many physical forces and environmental conditions.
SECTION 11 – MAINTENANCE AND STORAGE • • • • Car washing soap and water Glass cleaners without ammonia Mineral oil Multipurpose cleaners (such as Fantastik®, Formula 409®, etc.
SECTION 11 – MAINTENANCE AND STORAGE UltraleatherTM Leather-Like Upholstery Vinyl Fabrics –If Equipped Ultraleather synthetic leather fabric material has the luxurious look and feel of the finest European calfskin, with the durability and resistance to soils and stains of vinyl fabrics. It is also tougher than real calfskin and has superior resistance to punctures, snags, and rips.
SECTION 11 – MAINTENANCE AND STORAGE The following cleaning chart is provided as a guideline for care and cleaning of ceiling fabrics used in your coach. .
SECTION 11 – MAINTENANCE AND STORAGE NOTE: Many cabinetry and furniture items throughout this motorhome are constructed either partially or completely of real hardwoods. Because of natural variations in woodgrain density, slight differences in stain hue may exist between one item and another. This is the distinctive character and beauty of real wood. TABLES AND COUNTERTOPS Work surfaces are covered with a plastic or thermo-formed laminate that resists solvents, stains, and abrasions.
SECTION 11 – MAINTENANCE AND STORAGE GALLEY SINK Care and Cleaning Instructions The galley sink has been designed and engineered to resist scratches and should not stain under normal household use if used properly. To keep this product looking its best, we recommend that you take a few easy precautions. Marks or Discoloration White automotive rubbing compound may be used to remove stubborn marks or discoloration. Use of these products will not damage the solid surface. Always follow label directions.
SECTION 11 – MAINTENANCE AND STORAGE • • • • Use doormats (that do not contain bitumen) to keep out most of the dirt and dust. Remove spills immediately with a damp cloth, followed by rinsing with clean water. The use of stiletto heels is not recommended, as they may cause permanent damage to the flooring. Protect flooring from prolonged direct sunlight exposure.
SECTION 11 – MAINTENANCE AND STORAGE Clean and Prep Coach for Storage 1. Turn off the propane gas tank. 2. Turn the Electronic Thermostat switch OFF. 3. Remove all foods and items that may cause odors from cabinets and refrigerator. 4. Clean and defrost the refrigerator. Prop the door open slightly to allow any odors to dissipate. Place an open box of baking soda inside the refrigerator to help absorb odors. 5. Fully charge the batteries.
SECTION 11 – MAINTENANCE AND STORAGE 10. Check the toilet for proper operation. 11. Add water to the holding tank using the toilet flush pedal and galley sink faucet. Check to be sure dump valves seal tightly. 12. Check around all appliances for obstructions and ensure that all vent openings are clear. 13. Start refrigerator and check for proper cooling. 14. Clean wall and counter surfaces. 15.
SECTION 11 – MAINTENANCE AND STORAGE COACH MAINTENANCE CHART These recommendations apply for normal recreational use. Heavy duty or full-time use may require more frequent maintenance intervals.
SECTION 11 – MAINTENANCE AND STORAGE COACH MAINTENANCE CHART These recommendations apply for normal recreational use. Heavy duty or full-time use may require more frequent maintenance intervals. As Necessary Every Year Every 6 Months Every 3 Months Monthly Weekly Before Each Use Always use specified sections or manufacturer’s guide for further information and instructions.
SECTION 11 – MAINTENANCE AND STORAGE COACH MAINTENANCE CHART These recommendations apply for normal recreational use. Heavy duty or full-time use may require more frequent maintenance intervals. As Necessary Every Year Every 6 Months Every 3 Months Monthly Weekly Before Each Use Always use specified sections or manufacturer’s guide for further information and instructions.
SECTION 12 – MISCELLANEOUS NOTE: Your motorhome’s load capacity is designated by weight, not by volume, so you cannot necessarily use all available space when loading your motorhome. • Store or secure all loose items inside the motorhome before traveling. Possible overlooked items such as canned goods or small appliances on the countertop, cooking pans on the range, or free-standing furniture items can become dangerous projectiles during a sudden stop or evasive maneuver.
SECTION 12 – MISCELLANEOUS You will first drive only your front wheels onto the scale pad, then drive ahead so that the whole vehicle is on the scale, then finally pull off until just the rear wheels are on the pad. Front GAWR (Front Axle Only) GVWR - Whole Vehicle (All Axles) Corner Weighing (Side-to-Side) The most accurate method of weighing a motorhome is to weigh each “corner” of the coach separately (single L/R front wheels or L/R rear dual sets.
SECTION 12 – MISCELLANEOUS axle is 12,000 lbs., then the load on each rear dual set (left rear duals or right rear duals) should not exceed 6,000 lbs. Tires must be filled to the recommended air pressure for the highest loaded tire set on that axle. For example, on the rear axle, if the left side weighs more than the right, fill the left tires to the pressure required for that weight, then fill the right tires to the same pressure as the left ones.
SECTION 12 – MISCELLANEOUS Before descending a steep or long grade when towing a trailer, reduce speed and shift into a lower gear to control vehicle speed. Avoid prolonged or frequent application of brakes, which could cause overheating and brake failure. TRAILER WIRING CONNECTOR Your coach is pre-wired for trailer or car towing lights with a 7-pin socket. The following diagram shows proper connection of trailer or tow vehicle wiring to the coach light system.
SECTION 12 – MISCELLANEOUS this definition, the “trailer” can be a trailer, a vehicle towed on a dolly, or a vehicle towed by means of a tow bar. GCWR is typically specified based on durability and performance of the tow vehicle drive train: engine and cooling systems, transmission, drive line, drive axle, and others. The tow vehicle brakes may be rated for operation at GVWR, not GCWR.
SECTION 12 – MISCELLANEOUS Further Information For complete operating instructions, features, safety precautions, and maintenance care, refer to the awning manufacturer’s information provided in your InfoCase. STORAGE COMPARTMENT DOORS NOTE: Actual features and locations may vary depending on model, available equipment, and storage compartment configuration.
SECTION 12 – MISCELLANEOUS • • • • • • Do not overload. Ladder is intended for one person. Make sure you are physically capable to safely use the ladder. Strength, flexibility, and stability are required. Be aware that the vehicle may sway as you climb the ladder. Do not use the ladder in high winds. As you climb the ladder, grasp the side rails firmly and always use both hands. Keep your body centered between the side rails. Do not over-reach. Never allow children on the ladder.
SECTION 12 – MISCELLANEOUS Dome Crank Knob Fuse Fan Speed Selector Further Information See the power ventilator manufacturer’s operating instructions supplied in your InfoCase for further instructions, care, and cleaning information. EFFECTS OF PROLONGED OCCUPANCY Your motorhome was designed primarily for recreational use and short-term occupancy. If you expect to occupy your coach for an extended period, be prepared to deal with condensation and humid conditions that may be encountered.
About this Manual ....................................... 1-1 Air Conditioner Filter ................................ 4-10 Air Conditioner/Heater – Automotive (Dash) ........................................................ 3-5 Air Springs – Rear Helper ......................... 3-10 Audio-Video System Basic Operation ......... 8-3 Bathroom ................................................. 11-10 Battery Access ............................................. 6-6 Battery Boost Switch ............................
Index Power Sofas and Beds .................................. 2-7 Pre-Delivery Inspection ............................... 1-2 Pressure-Temperature Relief Valve ............. 4-7 Propane Gas Furnace ................................... 4-8 Propane Gas Furnace ................................... 4-9 Propane Gas Leak Detector ......................... 2-3 Propane Gas Leaks ....................................... 2-2 Propane Gas Pressure Regulator .................. 5-4 Propane Gas Supply .......................
