TO THE OWNER Congratulations! We welcome you to the exciting world of motor home travel and camping. You will find it convenient and enjoyable to have all the comforts of home and still enjoy the great outdoors wherever you choose to go. Your motor home has been carefully designed, engineered and manufactured to provide dependability as well as safety. Before sliding into the driver’s seat, take a few minutes to become familiar with operations and features.
CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, could result in damage mainly to equipment or property, but in some cases may also result in minor or moderate personal injury. NOTE: A ‘Note’ is not necessarily safety related but indicates a recommendation or special point of information that could assist in understanding the use or care of a feature item.
OWNER’S NAME STREET ADDRESS CITY AND STATE (OR PROVINCE IN CANADA) MOTOR HOME SERIAL NUMBER VEHICLE CHASSIS IDENTIFICATION NO. (VIN) DATE OF DELIVERY TO FIRST RETAIL PURCHASER VEHICLE MILEAGE AT TIME OF DELIVERY SELLING DEALER NAME AND ADDRESS TANK CAPACITIES Chassis Fuel Tank....................................................................................................................................... 75 gal. LP Gas Tank Brave model 30W .............................................................
INTRODUCTION Congratulations on the purchase of your new Brave motor home, which has been carefully designed, engineered and quality built by Winnebago Industries, Inc. ABOUT THIS MANUAL Please read this operator’s manual completely to understand how everything in your coach works before taking it on its “maiden voyage.” This manual is a guide to safe operation of the features, equipment and controls in this coach.
INTRODUCTION WARRANTY BEFORE DRIVING Before sitting in the driver’s seat, always check around your vehicle to be sure you have proper clearance for maneuvering. If necessary, have a passenger help guide you out of a difficult parking space. Although your coach features automotive conveniences like power steering and power brakes, driving a motor home is different from driving a car.
INTRODUCTION To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in Washington, D.C. area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.
INTRODUCTION VEHICLE CERTIFICATION LABEL This label contains vehicle identification and other important reference information. The vehicle certification label is located on the sidewall to the left of the steering wheel, or on the driver’s door. Never remove or destroy this label. MANUFACTURED BY INCOMPLETE VEHICLE MANUFACTURED BY MOTOR CORP.
INTRODUCTION EXTERIOR FEATURE IDENTIFICATION Actual locations of features depends on coach model and options. NOTE: Some equipment shown may be optional.
SECTION 1 SAFETY PRECAUTIONS Read and understand all instructions and precautions in this manual before operating your new motor home. About Safety Messages Used in This Manual Throughout this manual, certain items are labeled Note, Caution, Warning or Danger. These terms alert you to precautions that may involved damage to your vehicle or a risk to your personal safety. Read and follow them carefully.
SECTION 1 SAFETY PRECAUTIONS heater. They contain carbon monoxide, which is an odorless, colorless and poisonous gas. DRIVING · Do not attempt to adjust the driver’s seat while the vehicle is moving. · Do not adjust tilt steering in a moving vehicle. · Do not operate the cruise control on icy or extremely wet roads, winding roads, in heavy traffic, or in any other traffic situation where a constant speed cannot be maintained. · Use care when accelerating or decelerating on a slippery surface.
SECTION 1 SAFETY PRECAUTIONS WARNING IT IS NOT SAFE TO USE COOKING APPLIANCES FOR COMFORT HEATING Cooking appliances need fresh air for safe operation. Before operation 1. Open overhead vent or turn on exhaust fan. 2. Open window LP gas is present inside the coach. Because LP gas is heavier than air, the detector is located on a cabinet face near the floor of the coach. A green light on the face of the alarm shows when the unit is active. FAILURE TO COMPLY COULD RESULT IN DEATH OR SERIOUS INJURY.
SECTION 1 SAFETY PRECAUTIONS or an LP gas service center to have the problem corrected before using the LP system again. WARNING Never use an open flame to test for gas leaks. When testing for gas line leaks with a soapy water solution, DO NOT use a detergent containing ammonia or chlorine. These substances may generate a chemical reaction causing corrosion to gas lines, resulting in dangerous leak conditions. Power Connection The gas alarm is powered by the coach batteries.
SECTION 1 SAFETY PRECAUTIONS · · Avoid overloading electrical circuits. Replace fuses or circuit breakers with those of the same size and amperage rating only. Never use a higher rated fuse or breaker. Use caution when handling or working near electrical storage batteries. Always remove jewelry and wear protective clothing and eye covering. Avoid creating sparks. LOADING · · · Store or secure all loose items inside the motor home before traveling.
SECTION 1 SAFETY PRECAUTIONS · Each time the vehicle is raised for an oil change. · Whenever a change in the sound of the exhaust system is noticed. · Whenever the exhaust system, underbody or rear of the vehicle is damaged. To allow proper operation of the vehicle’s ventilation system, keep front ventilation inlet grill clear of snow, leaves or other obstructions at all times. DO NOT OCCUPY A PARKED VEHICLE WITH ENGINE RUNNING FOR AN EXTENDED PERIOD.
SECTION 1 SAFETY PRECAUTIONS RED LOOP Instructions for removal are also located on a label on the glass for quick reference and for passengers who may not be familiar with the exit. Never removed or destroy this label. WARNING Use emergency window for emergency exit only. Do not test for proper operation. If the cord is released by accident, but the glass remains in place, the cord can be replaced using a blunt instrument, preferably one made of plastic. We suggest you contact your dealer for assistance.
SECTION 1 SAFETY PRECAUTIONS We recommend that you become thoroughly familiar with the operating instructions displayed on the side of the fire extinguisher or in the information supplied in your Motor Home Operations Manual binder. We also recommend that you inspect the fire extinguisher for proper charge at least once a month in accordance with National Fire Protection Association (NFPA) recommendations as stated on the label. If the charge is insufficient, the fire extinguisher must be replaced.
SECTION 2 DRIVING YOUR MOTORHOME (See also Safety Precautions, Section 1 of this manual.) NOTE: See your Ford or Workhorse chassis operator's guide for information on starting the engine, operating the transmission, steering column controls descriptions of instrument gauges and other chassis related information. Some items described in this section may be optional or unavailable on your coach.
SECTION 2 DRIVING YOUR MOTOR HOME 3. Place front seats in the forward facing position. 4. Be sure to fasten all safety belts to fit you comfortably, but tight enough to obtain the full safety of the belts. 5. Make sure all doors are completely shut and locked. When the doors are shut and locked, there is less chance of the doors flying open in event of an accident. It also prevents unintentional opening of doors and keeps intruders out of your vehicle. 6. Check to see that all gauges are operating properly.
SECTION 2 DRIVING YOUR MOTOR HOME REPLACEMENT FUEL CAPS To protect gasoline system from excessive pressure or vacuum, or from sudden pressure, replace lost caps with caps of the same design available from your dealer. STARTING AND STOPPING ENGINE Refer to your chassis operating guide for the manufacturer's recommendations on starting and stopping the engine. Brake-Shift Interlock (Workhorse Chassis) Workhorse chassis are equipped with a brakeshift interlock safety feature.
SECTION 2 DRIVING YOUR MOTOR HOME Dead Deadbolt ELECTRIC ENTRANCE STEP The power switch for the electric entrance step is located to the left of the main entry door as you enter the coach. Door Handle Lock Entrance Door Handle - Inside Press lever to separate screen door from main entrance door Screen Door Latch - Inside Lubricate the locks periodically with graphite to maintain good working condition.
SECTION 2 DRIVING YOUR MOTOR HOME Stationary Retracted Mode To keep the step in the retracted position: • turn the Power Switch to On, • close the screen door to extend the step, • then turn the Power Switch to Off. The step will now stay retracted when the screen door is open or closed. This position is normally used where an exterior step is not required or to avoid damage to the setp, such as when parked near a high curb or similar object.
SECTION 2 DRIVING YOUR MOTOR HOME Lift to Slide Lift to Swivel 1 2 SEAT BELTS Passenger Seat - Aisle Side (Recline lever on opposite side) Seats intended for occupancy while the vehicle is in motion are equipped with seat belts for the protection of the driver and passengers. Lap Belts WARNING Do not adjust driver’s seat while vehicle is in motion. After adjusting seat, always use body pressure to make sure slide and swivel locking mechanism have engaged.
SECTION 2 DRIVING YOUR MOTOR HOME To Release: Press button in center of buckle and slide tongue out of buckle. · WARNING Snug and low belt positions are essential. This will ensure that the force exerted by the lap belt in a collision is spread over the strong hip area and not across the abdomen, which could result in serious injury. Only seats equipped with seat belts are to be occupied while vehicle is in motion.
SECTION 2 DRIVING YOUR MOTOR HOME More Info - To read more about power mirrors, see the mirror manufacturer’s information in your Owner InfoCase. MIRRORS Always adjust mirrors for maximum rear visibility before driving off. Make sure the seat is adjusted for proper vehicle control and that you are sitting back squarely into the seat. Power Electric Mirrors The electric mirrors are adjusted using a multi-directional switch located on the dash to the right of the steering column.
SECTION 2 DRIVING YOUR MOTOR HOME Video Center (Front Overhead Compartment) REARVIEW TV MONITOR SYSTEM - Optional If your motor home is equipped with this optional system, refer to the Owner InfoCase for specific instructions provided by manufacturer. INSTRUMENT PANEL GAUGES AND CONTROLS The illustrations on the following page showing switches and features provided by Winnebago.
SECTION 2 DRIVING YOUR MOTOR HOME INSTRUMENT PANEL Workhorse instruments shown for illustration purpose only. NOTE: Some equipment or controls shown may be optional or unavailable on your model.
SECTION 2 DRIVING YOUR MOTOR HOME MULTI-FUNCTION SIGNAL LEVER The multi-function signal lever controls the turn signals, high/low beam changing, windshield washer, wipers and wiper delay, and the electronic speed control (cruise) on some models.* See your chassis operating guide for complete operating information. *Ford chassis models have the cruise control system integrated into the steering wheel. See your Ford chassis guide for operating instructions.
SECTION 2 DRIVING YOUR MOTOR HOME 3. Turn the fan switch to high (largest dot). 4. Turn on auxiliary (dash) fans if additional air movement is needed B. For reduced defrosting: 1. Turn the temperature control knob to the left to an intermediate warm setting. 2. Adjust the fan speed for desired volume. VENTILATION A. To vent outside air into the vehicle when neither heating or cooling is required. 1. Turn the mode selection knob to VENT. 2.
SECTION 2 DRIVING YOUR MOTOR HOME WARNING Do not use the passenger side front workstation in the extended position while the vehicle is in motion. BEVERAGE TRAY - Storage Space Lifting the hinged top of the beverage tray will reveal room to store several small items. Aux. Batt. Switch (Near entrance door) The Aux. Batt switch is conveniently located near the entrance steps. Passenger Work Station - Optional Pull the workstation top backward toward you until it latches in the fully extended position.
SECTION 2 DRIVING YOUR MOTOR HOME in the direction needed to extend jack pairs according to lit yellow lights. ALWAYS LEVEL THE VEHICLE FROM SIDE TO SIDE BEFORE LEVELING THE VEHICLE FRONT TO REAR. Only one yellow LEVEL light can be on at one time. Extend jack pairs accordingly until all yellow lights are out. If the ground is too uneven, the jacks may not have enough stroke to level the vehicle. The vehicle may have to be moved or blocking placed under the pads. 5.
SECTION 2 DRIVING YOUR MOTOR HOME . SLIDEOUT ROOM The slideout living room provides a spacious living area at the push of a button. The slideout room is extended and retracted using a hydraulic mechanism with an electronic control system. The slideout control switch is located near the leveling system pad on the lower left dash area. CAUTION Release slideout room travel straps before attempting to extend slide-out room. Fasten travel straps before driving vehicle. See instructions below.
SECTION 2 DRIVING YOUR MOTOR HOME · WARNING To Retract SlideOut Room: Keep all persons clear of the slideout room and moving parts while extending or retracting. Do not occupy the slideout room while it is being extended or retracted. CAUTION Although there is an awning over the roof of the slideout room, there is a possibility of debris getting onto the roof.
SECTION 2 DRIVING YOUR MOTOR HOME using the control switch, you can manually retract the room using the emergency winch system described below. The winch is stored in a basement storage compartment. WARNING Stop engine, place transmission in parking position and apply parking brake before lying beneath vehicle for this procedure. DO NOT OPEN ANY OF THE 4 VALVES ON THE OUTBOARD END OF THE PUMP because they regulate the leveling jacks.
SECTION 2 DRIVING YOUR MOTOR HOME Winch attachment beneath dinette seat · Guide strap through cutout in aisle side of dinette seat at carpet level. Insert hook into sewn loop end of strap from beneath couch. · Crank winch handle clockwise slowly, a few “clicks” at a time, until the room is fully retracted. Allow about 10 minutes to crank room in fully. NOTE: Attempting to crank room in too quickly will raise pressure in hydraulic fluid lines and make cranking more difficult.
SECTION 3 IN CASE OF DRIVING EMERGENCY SPARE TIRE STORAGE HAZARD WARNING FLASHER The hazard warning flasher provides additional safety when the vehicle must be stopped on the side of the roadway and presents a possible hazard to other motorists. When the flasher is on, it serves as a warning to the other drivers to approach and overtake your vehicle with caution. WARNING Operating the hazard warning flasher system while moving on the highway is illegal.
SECTION 3 IN CASE OF DRIVING EMERGENCY MOTOR HOME TIRE CHANGING PROCEDURE WARNING We advise you to obtain qualified road service whenever possible. Do not try to change a tire yourself except under emergency conditions, and only by closely following instructions in this manual and the chassis operating guide. If you do satisfactorily complete an emergency tire change, we recommend that you have the wheel nuts checked and properly torque tightened by qualified service personnel as soon as possible.
SECTION 3 IN CASE OF DRIVING EMERGENCY 1. Place jack under jacking point specified in your chassis operating guide. Position jack so it may be operated without placing your body beneath vehicle. 2. Screw jack extension pad out (up) until it touches jacking point surface. 3. Begin jacking until jack is firmly positioned and just begins to bear weight, but do not lift tire off the ground. 4. “Crack” wheel nuts loose with lug wrench, but do not unscrew nuts yet. 5.
SECTION 3 IN CASE OF DRIVING EMERGENCY JUMP STARTING WARNING Automotive batteries produce caustic acid, explosive gases, and electrical current which may cause burns. It is important that the instructions below are followed exactly, or personal injury (particularly to eyes) or property damage may result due to battery explosion, battery acid, or electrical (short circuit) burns. • • • • NEVER smoke near the battery or expose it to open flame or electrical sparks.
SECTION 3 IN CASE OF DRIVING EMERGENCY CONNECTING A BATTERY CHARGER To connect a battery charger, first make sure the engine is switched off. Disconnect the negative lead from the battery. Never disconnect the battery while the engine is running or alternator damage could result. Connect the positive “+” (red) lead of the charger to the positive “+” terminal on the battery. Next, connect the negative “-” (black) lead of the charger to a suitable ground. Finally, plug in or switch on the charger.
SECTION 4 TRAVELING WITH YOUR MOTORHOME (See also SAFETY PRECAUTIONS, Section 1 of this manual.) LOADING THE VEHICLE NOTE: Your motor home’s load capacity is designated by weight, not by volume, so you cannot necessarily use all available space when loading your motor home. When loading the vehicle, distribute the cargo load equally so that you do not exceed either the Front or Rear Gross Axle Weight Rating (GAWR) or the Gross Vehicle Weight Rating (GVWR).
SECTION 4 TRAVELING WITH YOUR MOTOR HOME Weighing: There is typically a scale operator to direct you but the basic routine is to take three separate weights - front axle, whole vehicle, and rear axle. You will first drive only your front wheels onto the scale pad, then drive ahead so that the whole vehicle is on the scale, then finally pull off until just the rear wheels are on the pad.
SECTION 4 TRAVELING WITH YOUR MOTOR HOME loaded weight of the coach and the towed vehicle. See preceding items “Loading the Vehicle” and “Weighing Your Loaded Vehicle” for explanation of weight ratings. Because of individual vehicle use and loading habits, we recommend weighing the vehicle while fully loaded to avoid exceeding any of the listed Gross Weight Ratings. See “Vehicle Certification Label” in the Introduction Section for information on gross weight ratings.
SECTION 4 TRAVELING WITH YOUR MOTOR HOME - Sewer and Water Supply Hose - Unhook and store. - TV Antenna - Make certain the TV antenna and/or satellite dish are lowered and seated in their support cradles. - Loose Items Inside the Motor Home - Store or secure items. - Pilot Lights - Make sure all pilots are off. - Fuel Tanks - Check level. - Water Tank - Fill with fresh water. - Exterior Door and Step - Make sure doors are closed, locked and step retracted.
SECTION 4 TRAVELING WITH YOUR MOTOR HOME · During a flash flood, if you cannot move your vehicle, abandon it. Do not attempt to return to your vehicle before the water has receded. · Do not attempt to wade to your vehicle if the water is above your knees - fast moving water exerts an enormous amount of pressure, making it impossible to remain standing or walking. · Do not try to drive through flooded areas.
SECTION 4 TRAVELING WITH YOUR MOTOR HOME NIGHTTIME DRIVING · · Make sure all running lights and signal lights are clean and in working order. Have your headlights periodically checked and adjusted. Use care when passing other vehicles. Your motor home is a longer vehicle than a car, and you may have a more difficult time knowing when to pull back into your lane. If possible, have another person in the coach help you watch while maneuvering your motor home in traffic. ing action.
SECTION 4 TRAVELING WITH YOUR MOTOR HOME HUMIDITY AND CONDENSATION True Level Blocks under downhill wheel(s) Leveling Your Motor Home When placing blocks beneath a set of rear dual wheels, be sure the blocks support both tires so that the load weight is not resting on one tire, which could damage that tire. THIS NOT THIS Moisture condensing on the inside of windows is a visible indication that there is too much humidity inside the coach.
SECTION 5 LP GAS SYSTEM (See also Safety Precautions, Section 1 of this manual.) LP GAS SUPPLY The LP gas system supplies fuel for the range, water heater, furnace and refrigerator (while in gas mode). When used and handled properly, this system is safe and economical and provides modern living conveniences wherever you travel. · Have the entire LP gas system inspected for possible leaks and missing or damaged parts at each tank filling.
SECTION 5 LP GAS SYSTEM LP Gas Tank Tank Supply Valve Overflow Valve Brave models 30W ............................18 gal.* (23 gal. w.c.) Brave model 32V, 34D & 36M .........23 gal.* (28 gal. w.c.) *LP Gas tank capacity shown is the usable “full” LP gas capacity, which is 80% of the tank manufacturer’s listed water capacity (w.c. shown in parenthesis). An LP tank must have at least 20% of tank volume free to allow for expansion and proper vaporization of the liquid fuel.
SECTION 5 LP GAS SYSTEM come sooted and lose efficiency by using butane fuel. REFILLING LP TANK There are many LP gas refueling stations located throughout the country. These stations are listed in the telephone directory Yellow Pages under “Gas - Liquified Petroleum - Bottled and Bulk.” Since the LP tank is permanently mounted to the frame, the motor home must be taken to an LP dealership for filling. Do not attempt to remove the LP tank from the vehicle.
SECTION 5 LP GAS SYSTEM REGULATOR The pressure regulator is protected from the elements by a plastic cover which should be left in place at all times. Only your dealer or a qualified LP gas service should remove the regulator cover for adjustments. Be sure vent hole is not blocked WARNING Inspect the pressure regulator vent hole periodically for blockage. If any obstruction is apparent, have the regulator serviced by your dealer or a qualified LP gas service center.
SECTION 5 LP GAS SYSTEM DANGER IF YOU SMELL GAS 1. 2. 3. 4. 5. 6. EXTINGUISH ANY OPEN FLAME, PILOT LIGHTS AND ALL SMOKING MATERIALS. DO NOT TOUCH ELECTRICAL SWITCHES. SHUT OFF THE GAS SUPPLY AT THE TANK VALVE(S) OR GAS SUPPLY CONNECTIONS. OPEN DOORS AND OTHER VENTILATING OPENINGS. LEAVE THE AREA UNTIL ODOR CLEARS. HAVE THE GAS SYSTEM CHECKED AND LEAKAGE SOURCE CORRECTED BEFORE USING AGAIN. FAILURE TO COMPLY COULD RESULT IN EXPLOSION RESULTING IN DEATH OR SERIOUS INJURY.
SECTION 6 ELECTRICAL SYSTEMS (See also Safety Precautions, Section 1 of this manual.) Your motor home is equipped with an electrical system consisting of two separate voltages; a 12-volt DC system and a 110-volt AC system. The 12-volt system consists of two internal power sources, while the 110-volt system is operated from an outside power source or the optional 110-volt generator. All systems operate through a single power converter control center to provide electrical power to the motor home.
SECTION 6 ELECTRICAL SYSTEMS 30 Amp Receptacle 50 Amp. Power Receptacle The optional 50-amp shoreline gives your coach extra current handling capacity. This allows you to run the central air conditioning system at maximum (both compressors running) while using other electrical equipment without fear of constantly tripping the shoreline pole circuit breaker.
SECTION 6 ELECTRICAL SYSTEMS WARNING Do not store anything around or on top of the converter, or in front of the cover. The converter generates heat while operating, and needs unrestricted air flow for proper cooling. Charging Section The converter charges coach batteries while 110-volt external power is connected. The converter will automatically “sense” the condition of the RV battery. If it is below “full charge”, the Charging Section will start charging the battery.
SECTION 6 ELECTRICAL SYSTEMS GROUND FAULT CIRCUIT INTERRUPTER Exterior, bath and galley outlets are connected to a GFCI (Ground Fault Circuit Interrupter), which is an extremely sensitive circuit breaker that will help to protect against severe electrical shock if a ground fault develops. If such a condition occurs, the GFCI will break the circuit by turning off the power to the protected outlets.
SECTION 6 ELECTRICAL SYSTEMS This coach may be equipped with one of several models of generators. Consult the generator owner’s manual in your Owner’s InfoCase for specific instructions on starting and stopping your generator. Stopping: · · Before shutting generator down, turn off electrical loads and let engine run at no-load for a few minutes to cool down. Press the generator switch Off and hold until the generator engine comes to a complete stop.
SECTION 6 ELECTRICAL SYSTEMS Operation Warnings and Cautions WARNING The exhaust of all internal combustion engines contains carbon monoxide (CO). This poisonous gas is colorless, odorless, tasteless, and lighter than air. The exhaust systems of both your motor home engine and your generator engine have been installed with your safety in mind. However, certain precautions must be taken when using them to protect yourself from conditions beyond the control of the manufacturer.
SECTION 6 ELECTRICAL SYSTEMS BATTERY STORAGE AND MAINTENANCE House 12V Circuit Breakers A label on the panel states the amperage rating and circuit protected for each fuse or breaker. BATTERY INFORMATION BATTERY ACCESS The batteries are located beneath the top inside entrance step. Unhook the latch assembly fastening the top step and remove. Removable Step Latch Lead -acid type batteries are electro-chemical devices for storing and releasing electrical charge.
SECTION 6 ELECTRICAL SYSTEMS can lose electrolytic fluids and become damaged from continuous charging without periodic use. WARNING We recommend following regular battery inspection and maintenance, especially in cold weather. Before removing any battery cables or battery, make sure all 12-volt equipment in the motor home is off and the power cord has been disconnected. Further precautions are: · Remove the battery from the coach.
SECTION 6 ELECTRICAL SYSTEMS WARNING To prevent wiring damage, it is essential when replacing the cables on the battery, or when using a “booster” battery, that the positive post and the positive cable be attached and the negative post and negative cable be attached. The posts are marked (+) plus and (-) minus. If a “fast charger” is used while battery is in the motor home, disconnect both battery cables before connecting the charger. Never attempt to charge or boost a frozen battery.
SECTION 6 ELECTRICAL SYSTEMS CAUTION The CB radio could become damaged if the CB antenna SWR is not adjusted before operating the CB radio. TRAILER WIRING CONNECTOR Your coach is pre-wired for trailer or car towing lights with a 6-pin socket on the rear bumper. The connector plug is supplied in the coach parts package provided to you by your dealer when you took delivery of the vehicle. The diagram shows proper connection of trailer or tow vehicle wiring to the coach light system.
SECTION 7 PLUMBING SYSTEMS FRESH WATER SYSTEM The fresh water system provides water to the galley sink, shower, bathroom lavatory, toilet and water heater. Water may be supplied by either of two sources: - a water tank located within the motor home, or - any external water source to which the motor home may be connected, known as “city water”. FRESH WATER TANK FILLING PROCEDURES: Always fill the fresh water tank at an approved potable water filling facility or a known purified drinking water source.
SECTION 7 PLUMBING SYSTEMS Fresh Water Tank Capacity Brave model 30W .......................................78 gal. Brave model 32V (Ford).............................80 gal. Brave model 32V (Workhorse) ................. 58 gal. Brave model 34D....................................... 80 gal. Brave model 36M ...................................... 70 gal. Pump Strainer Filter The pump is equipped with a cleanable strainer filter to capture any possible tank borne particles that could damage pump components.
SECTION 7 PLUMBING SYSTEMS Initial Water Line Priming 1. Make sure that all water drain valves are closed, including water heater valve. (Refer to Section 10.) 2. Turn water pump switch to “OFF” position. 3. Fill water tank. 4. Open all faucets, hot and cold. 5. Turn on pump switch. 6. Close each faucet as it begins to deliver a steady stream of water (close cold water first). Leave hot water faucets on until they also deliver a steady stream of water.
SECTION 7 PLUMBING SYSTEMS Replacing the water filter cartridge: Replace the filter cartridge when water flow from the purifier faucet is too slow for convenience. · · · Place a container beneath the filter to catch any remaining water during removal. Raise the valve handle near the top of the filter base to block water flow to filter. Twist the filter cartridge counterclockwise about a quarter-turn and pull it down and out of the filter head. 4. Turn on the external water source (faucet).
SECTION 7 PLUMBING SYSTEMS 3. Disconnect the hose from the vehicle and replace the cap on the connection. SHOWER HOSE VACUUM BREAKER After using the shower, you may notice water dripping from the shower faucet assembly. The dripping results when vacuum in the shower hose (after closing the shower faucet) slowly releases and allows water remaining in the hose to drain down. This is a normal function of the shower valve assembly and is not a leak or defect.
SECTION 7 PLUMBING SYSTEMS 8. Rinse sewer hose thoroughly with water and stow. NOTE: We recommend that you dump all holding tanks before traveling to avoid carrying unnecessary weight. Pull last to drain gray tank Pull first to drain black tank DUMPING HOLDING TANKS 1. Remove drain hose from exterior storage compartment. 2. Remove dust cap from drain and connect drain hose. Be sure it is firmly attached. 3. Place the other end of sewer hose into disposal opening. 4.
SECTION 7 PLUMBING SYSTEMS DRAIN DRAIN CLOSE CLOSE LINE-END VALVE IN-LINE VALVE Water Drain Valves (typical) Water Tank Drain Valve In Right Side Rear Cargo Compartment Water Line Drain in right front compartment 7-7
SECTION 7 PLUMBING SYSTEMS TANK CAPACITIES HT1 - Black Water Holding Tank Brave model 30W (Toilet & Lavatory) ......................................................................................40 gal. Brave model 32V (Toilet) ..........................................................................................................40 gal. Brave model 34D (Toilet) ..........................................................................................................50 gal. Brave model 36M (Toilet).....
SECTION 7 PLUMBING SYSTEMS WATER SYSTEM DRAIN VALVE LOCATIONS SYSTEM Water Lines: DRAIN VALVE LOCATIONS One (1) valve in the front storage compartment on the passenger side of the coach. Open exterior shower faucet and lay shower head on ground. Also, to drain any water left in the city water line, place the tip of your finger inside the city water connection and gently press the backflow valve (small “button” in center of connector).
SECTION 8 APPLIANCES & INTERIOR FEATURES (See also Safety Precautions, Section 1 of this manual.) NOTE: Because this model is available in several sizes and floor plans, some items described may be optional or unavailable on your coach. A small round bubble level is provided with your refrigerator. Place the bubble level on the bottom surface of the refrigerator and watch the position of the bubble in relation to the circle in top of the level.
SECTION 8 APPLIANCES & INTERIOR FEATURES OPERATING INSTRUCTIONS Norcold Models with Electronic Auto Mode Control Push door handle downward and pull to open refrigerator. Lift freezer handle upward to open. The ON/OFF button turns the refrigerator On or OFf. If the button is pressed, it will turn the refrigerator On and set the mode to AUTO. When the refrigerator is On, pressing this button for 2 seconds will turn the refrigerator Off.
SECTION 8 APPLIANCES & INTERIOR FEATURES AUTO indicator and the LP GAS indicator will illuminate. After 10 seconds, the LP GAS indicator will turn off and only the AUTO indicator will remain illuminated. Press and quickly release any button to display the operating mode. During operation in the AUTO mode, when a higher priority power source becomes available, the operating controls will cease using the current power source and will switch to the higher priority power source.
SECTION 8 APPLIANCES & INTERIOR FEATURES the freezer and fresh food compartment temperatures. (Frequent door opening prevents the temperatures from stabilizing.) Although the refrigerator can operate in this mode, Norcold recommends that you seek service to restore manual operation as soon as practical. REFRIGERATOR COMPARTMENT (Exterior) The exterior refrigerator compartment allows access to the rear of the refrigerator for inspection, maintenance and service.
SECTION 8 APPLIANCES & INTERIOR FEATURES The following warning label has been located in the cooking area to remind you to provide an adequate supply of fresh air for combustion. WARNING IT IS NOT SAFE TO USE COOKING APPLIANCES FOR COMFORT HEATING Cooking appliances need fresh air for safe operation. Before operation 1. Open overhead vent or turn on exhaust fan. 2. Open window WARNING FAILURE TO COMPLY COULD RESULT IN DEATH OR SERIOUS INJURY.
SECTION 8 APPLIANCES & INTERIOR FEATURES Operating Oven Control Push in and turn the oven control knob (counterclockwise) to the desired temperature setting. There is a delay of about 45 seconds before the main burner ignites. This is normal and there is no gas escaping during this delay. It is also normal for the oven burner flame to cycle off and on at all temperatures except broil (BR).
SECTION 8 APPLIANCES & INTERIOR FEATURES Tank Capacities See back of “To The Owner” page inside front cover of this manual. LP Gas Level Press and hold the “Levels Test” switch to show approximate LP tank level. The LP level is registered by a sending unit on the tank. The gauge mounted on the side of the tank will give a more accurate indication of actual tank level if needed. Water And Holding Tank Levels Press and hold the “Levels Test” switch to show approximate level on the monitor lights.
SECTION 8 APPLIANCES & INTERIOR FEATURES b) Remove red wire from left-hand terminal of ECO switch (ECO to valve). Generator Start/Stop Switch See Section 6, Electrical Systems for generator start-up and shut-down instructions. Generator Hourmeter See Section 6, Electrical Systems for generator hourmeter information. WATER HEATER Direct Ignition Models Water Heater Capacity: 6 gal. 1. Place Water Heater switch in the “On” position. The switch and “WH Pilot” light are located on the monitor panel.
SECTION 8 APPLIANCES & INTERIOR FEATURES 2. Open a faucet in the motor home to relieve water pressure. 3. Pull the handle of the P-T valve straight out and allow water to flow until it stops. Open CAUTION Lift handle straight out to open P-T valve 4. Let the handle of the P-T valve snap shut. 5. Close the faucet and turn on the water supply before switching the water heater on. Leave by-pass valve handle in NORMAL position if draining water and blowing out water lines.
SECTION 8 APPLIANCES & INTERIOR FEATURES Motor Aid Water Heater and Rear Auxiliary Heater Maintenance Have your authorized dealer check all hose clamp connections on the rear automotive heater and the motor aid water heater at least every six months and tighten them if necessary. LP GAS FURNACE (SUBURBAN) Start Up: 1. Open the LP gas tank valve by turning fully counterclockwise. not recommend removing the smoke alarm battery.
SECTION 8 APPLIANCES & INTERIOR FEATURES heat pump. The heat pump will not operate when the outside temperature falls below 36 degrees F. To operate the heat pump: • Slide the Thermostat switch to Electric heat mode. • If the inside temperature is 5 degrees or more below the thermostat set point, both the heat pump and the furnace will run initially to bring the interior temperature up to the set point as quickly as possible.
SECTION 8 APPLIANCES & INTERIOR FEATURES Operation The following chart shows the system functions with the “Heat/Cool” thermostat. Disregard references to heat functions when using the “Cool Only” thermostat in the rear bedroom. TV ANTENNA The TV antenna on your motor home can be easily raised, rotated a full 360° and lowered from inside the vehicle by simply turning a crank or rotating knob.
SECTION 8 APPLIANCES & INTERIOR FEATURES Rotating Antenna - Make sure antenna is in the “UP” position. Pull down on rotating knob until it disengages ceiling plate and rotate for best picture and sound on TV set. SIGNAL AMPLIFIER The amplifier power switch is located on the video selector system panel in the driver’s compartment overhead cabinet. To operate amplifier, turn on power switch.
SECTION 8 APPLIANCES & INTERIOR FEATURES for best picture. Then turn off the amplifier power switch. If the antenna amplifier is working properly, the TV picture will now be degraded (snowy). When you turn the switch back on, the picture should again be sharp. CHECKING PERFORMANCE The TV signals available to an RV are entirely dependent on its location in relation to the transmitter. Signals may vary from strong to no usable signal at all.
SECTION 8 APPLIANCES & INTERIOR FEATURES DC-AC ELECTRICAL VOLTAGE INVERTER - Optional SLEEPING FACILITIES WARNING Do not use sleeping facilities while vehicle is moving. The voltage inverter changes 12 volt DC current into 110 volt AC current to operate your TV and VCR while traveling or when shoreline hookup is not available. · The inverter must be switched on to operate. · Turn the inverter off when not in use to avoid draining the coach or automotive batteries.
SECTION 8 APPLIANCES & INTERIOR FEATURES 3. Remove the table from the wall support bracket by lifting the end of the table. Then lower the table to rest on the cleats attached to each dinette bench. Rest EasyTM Multi-Position Lounge Optional (If equipped) 4. Arrange dinette cushions to cover bed area. To Revert to Dinette: 1. Replace the table onto the wall support and lower the table leg. 2. Make sure that the table leg is secured into the floor support bracket and the leg brace is locked.
SECTION 8 APPLIANCES & INTERIOR FEATURES To Extend Pull-Out Footrest Section: Reach through the ‘dip’ opening in the center of the lounge front as shown. Squeeze the latch on the inside of the lower face panel and pull the lower ‘trundle’ section of the lounge outward until fully extended. The gap between the footrest and seat provides ample room to enter and exit the lounge. If desired, however, the footrest section can be pushed against the lounge seat.
SECTION 8 APPLIANCES & INTERIOR FEATURES WARNING To avoid injury to young children, do not allow them to operate the sofa, or to play within the sofa or near the operating mechanism. Hoop Chair Mount The hoop base of lounge chair is mounted to the floor with a clamp as shown. CAUTION The chair must be clamped back into place before driving the coach. FRESH WATER TOILET The clamp knob can be unscrewed and removed to allow you to position the chair as you desire in the living area of the coach.
SECTION 8 APPLIANCES & INTERIOR FEATURES 2. To add more water to the bowl than the normal 2” automatic refill, lift the pedal and hold until desired amount has been added. Release pedal slowly. 4. Remove the water line from the base of the toilet and clean the screen. 5. If the flush valve becomes stiff after extended use, it may be lubricated with a silicone spray.Turn the water pump off and operate flush pedal to drain water from the toilet bowl.
SECTION 8 APPLIANCES & INTERIOR FEATURES SLIDER WINDOWS Lift the latch handle straight out from the window. Grasp the sliding window edge frame and slide the window to the side. Be sure the latch is raised before trying to slide the window closed. To loosen the tension, unwrap the guide cords from the spools one turn at a time until desired tension is achieved. DAY/NIGHTER PLEATED BLINDS Your coach may feature two-stage pleated window blinds that can be used for daytime or nighttime privacy.
SECTION 8 APPLIANCES & INTERIOR FEATURES After replacing the battery, simply place the clock back into the socket with 12 at the 9 o’clock position and rotate upright. COFFEE MAKER - Optional The manufacturer’s instructions for use and care are included in your operation manual binder. To Remove for cleaning: · Unplug the coffee maker from the electrical receptacle and remove the carafe (pot) from the burner plate.
SECTION 9 CARE & MAINTENANCE CAUTION Sealants must be inspected every 6 months and resealed if necessary. ROOF The roof is made of Thermo-Panel materials like the walls and floor. It will support the weight of an average adult should it become necessary to repair the roof or roof mounted components. It is not recommended, however, that very large or heavy objects be carried on the roof while the vehicle is in motion. (See page 4-1 for roof loading specifications.
SECTION 9 CARE & MAINTENANCE Stains and Discolorations Regular cleaning and waxing will help prevent most discolorations and stains; however, please be aware that using caustic, highly alkaline cleaners or any cleaner with ammonia may actually darken your RV’s exterior. If stains or discolorations do appear, they can be removed by gently wet-sanding the discolored area with a fine grit sandpaper and then using an electric or pneumatic buffer and a liberal amount of rubbing compound.
SECTION 9 CARE & MAINTENANCE ing products. Some water-based household cleaning products are not formulated for use on fabrics and may cause excessive shrinkage or fading. Always test any cleaning product on a hidden area of fabric before using on visible areas. For best results, fabric cleaning should be referred to a professional carpet and upholstery cleaner.
SECTION 9 CARE & MAINTENANCE IMPORTANT: Make sure you have selected the right cleaning agent from the list below before your begin the cleaning process. NOTE: In many cases listed in the chart below, repeated steps may be required to fully extract contaminant from material. Items listed with (*) may also be removed through steam extraction method by a professional cleaner or service.
SECTION 9 CARE & MAINTENANCE IMPORTANT: The fabric manufacturer’s recommendeds made above are done in good faith and are based on a history of actual experiences and laboratory evaluations. Foss Manufacturing Company, Inc. and/or its designed distributor does not warrant, either expressed or implied, the effectiveness of the cleaning agents listed and the process for cleaning described above.
SECTION 9 CARE & MAINTENANCE Avoid paint remove or oven cleaner. The solid surface material is also resistant to most chemical substances but exposure to some harsh chemicals and solvents such as these can cause damage that would need professional repair or replacement. If one of these materials does spill or drip onto the counter surface, wipe it up immediately to avoid damage. Technical Assistance.
SECTION 9 CARE & MAINTENANCE To Reset Oil Change Reminder: • Turn the ignition switch to “ON” but Do Not Start the engine. • Fully press-and-release the accelerator pedal 3 times within 5 seconds, then turn ignition “OFF” for at least 10 seconds. • The 3000-mile oil life counter on the engine controller will be reset to start a new cycle. ENGINE ACCESS HOOD Insert the tamper-resistant hood key into the hood locks and turn them to the right (clockwise) to unlock the hood. Swing the hood outward and down.
SECTION 9 CARE & MAINTENANCE TIRES Low air pressure results in tire overloading and abnormal wear and also affects handling and fuel economy. Obtain proper inflation pressures from your chassis operating guide or tire manufacturer. need to be balanced if uneven wear is detected or if ride comfort decreases noticeably. See your chassis operating guide for further information. FRONT AIR SPRINGS - Workhorse Chassis Some workhorse chassis are equipped with air bags inside the front suspension springs.
SECTION 9 CARE & MAINTENANCE AUTOMOTIVE 12-VOLT FUSES AND CIRCUIT BREAKERS The automotive fuses and breaker are conveniently located on a panel beneath the hinged instrument panel pod. Lift the pod upward as shown. The circuit breakers will pop outward if they are tripped. Simply push in to reset. Always replace plug-in type fuses with those of the same amperage size. See chassis guide for fuse application table.
SECTION 10 STORING YOUR MOTOR HOME PREPARING VEHICLE FOR STORAGE Properly preparing your vehicle for storage will lessen the possibility of damage to your vehicle. Prepare the motor home for vacancy just as you would if you were leaving your house for an extended period: · · · · · · Remove all perishables from cabinets and refrigerator Prop refrigerator door open. Turn off LP gas tank. Drain water heater, water tank and holding tank. Drain optional washer/dryer.
SECTION 10 STORING YOUR MOTOR HOME 5. Install the antifreeze diverter plug • Raise the valve handle on the filter base. • Hold the diverter by the support bar as shown and guide it up into the filter base. • Push the diverter up into the head as far as possible and turn it clockwise approximately 90° until it stops. • Lower valve handle to lock the diverter plug in place.
SECTION 10 STORING YOUR MOTOR HOME 8. After water has stopped draining at all faucets and drain valves, connect a “blow-out” plug to the city water connection on the coach. Then use a compressed air hose regulated to 30 psi or less to force air through the system. (A “blow-out” plug can be purchased at any Winnebago or Itasca dealer. P/N 701705-01-000.) City Water Connection 11. Now turn air pressure off and disconnect water purge adapters.
SECTION 10 STORING YOUR MOTOR HOME Water System Winterization Valve Your coach is equipped with a manually operated water line winterization system for your convenience in winterizing fresh water lines. The system features a diverter valve and suction tube in-line between the tank and water pump to draw non-toxic RV water system antifreeze into the water lines. This feature is located near the water pump and drain valves. See page 7-7 or 7-8 for location in your coach.
SECTION 10 STORING YOUR MOTOR HOME 15. Have the vehicle chassis completely serviced and lubricated. Be sure radiator antifreeze protection level is sufficient for the lowest anticipated temperatures. 16. Wash and wax the coach. 17. Inspect all seams and seals around doors, windows, vents, and any other joints. Replace or repair any that are damaged. Sealing materials and compounds can be purchased from your dealer. Badly damaged weather seals may need to be replaced by your dealer. 18.
SECTION 10 STORING YOUR MOTOR HOME during storage periods because the batteries can lose electrolytic fluids and become damaged from continuous charging without periodic use. We recommend following regular battery inspection and maintenance, especially in cold weather. See “Battery Maintenance” in Section 6 - Electrical Systems. REMOVAL FROM STORAGE 1. Completely air out the motor home. 2. Have the entire LP gas system checked for leaks. 3. Check window operation. 4. Check cabinet and door hinges.
INDEX 110-Volt AC System..................................... 6- 1 110-Volt Circuit Breakers............................. 6- 3 110-Volt Receptacles (Outlets)..................... 6- 3 12-Volt DC System....................................... 6- 6 12-Volt House Fuses and Circuit Breakers... 6- 6 A About This Manual ....................................... 0- 1 Air Conditioning ......................................... 2- 12 Air in the LP Gas Tank ................................. 5- 3 Armrest Adjustment.......
INDEX F Filling the Tank............................................. 2- 2 Fire Extinguisher........................................... 1- 7 Formaldehyde Information ........................... 1- 5 Fresh Water System ...................................... 7- 1 Fresh Water Toilet ...................................... 8- 18 Front Air Springs .......................................... 9- 8 Front Axle Tire Alignment ........................... 4- 1 Front Wheel .................................................
INDEX R Radio Power Switch...................................... 2- 8 Range and Oven............................................ 8- 4 Range and Refrigerator ................................. 9- 6 Range Hood .................................................. 8- 6 Rear Coach Heater ...................................... 2- 12 Rearview TV Monitor System ...................... 2- 9 Recovery Towing.......................................... 3- 3 Refrigerator ...................................................
IMPORTANT SERIAL NUMBERS Motor Home (Coach): Year _________ Model ___________________ Serial _____________ Chassis: Make ___________________ Serial (VIN) ______________ Roof Air Conditioner: Furnace: Water Heater: Power Converter: 110-Volt Generator: Range: Microwave Oven: Refrigerator: Television: Video Cassette Player: Brand ___________ Brand ___________ Brand ___________ Brand ___________ Brand ___________ Brand ___________ Brand ___________ Brand ___________ Brand ___________ Brand ___________ Model
MAINTENANCE RECORD Date Odometer Mileage Description of Service Cost
FUEL & OIL RECORD Date Odometer Mileage Fuel Gal. Oil Qts. MPG Cost Date Odometer Mileage Fuel Gals. Oil Qts.
FUEL & OIL RECORD Date Odometer Mileage Fuel Gal. Oil Qts. MPG Cost Date Odometer Mileage Fuel Gals. Oil Qts.
