TO THE OWNER Congratulations! We welcome you to the exciting world of motor home travel and camping. You will find it convenient and enjoyable to have all the comforts of home and still enjoy the great outdoors wherever you choose to go. Your motor home has been carefully designed, engineered and manufactured to provide dependability as well as safety. Before sliding into the driver’s seat, take a few minutes to become familiar with operations and features.
CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, could result in damage mainly to equipment or property, but in some cases may also result in minor or moderate personal injury. NOTE: A ‘Note’ is not necessarily safety related but indicates a recommendation or special point of information that could assist in understanding the use or care of a feature item.
OWNER’S NAME STREET ADDRESS CITY AND STATE (OR PROVINCE IN CANADA) MOTOR HOME SERIAL NUMBER VEHICLE CHASSIS IDENTIFICATION NO. (VIN) DATE OF DELIVERY TO FIRST RETAIL PURCHASER VEHICLE MILEAGE AT TIME OF DELIVERY SELLING DEALER NAME AND ADDRESS TANK CAPACITIES Chassis Fuel Tank....................................................................................................................................... 75 gal. LP Gas Tank Model 30W....................................................................
2004 NEW VEHICLE LIMITED WARRANTY WINNEBAGO INDUSTRIES, INC. WARRANTY COVERAGE TO OWNER Winnebago Industries, Inc. of Forest City, Iowa warrants each new Winnebago Industries motor home to the owner for use in the U.S.A. and Canada as follows: WARRANTY PERIOD The Warranty Period for all coverages begins on the date the vehicle is delivered to the first retail purchaser or first placed in service as a demonstrator or company vehicle.
WINNEBAGO INDUSTRIES’ RESPONSIBILITY Any part of the vehicle subject to warranty which is found to be defective in material or workmanship, will be repaired or replaced at Winnebago Industries’ option upon notice of the defect without charge to the customer for parts or labor. While any Winnebago Industries motor home dealer can perform warranty service, we recommend you return to the dealership that sold you your vehicle.
TABLE OF CONTENTS INTRODUCTION About This Manual ....................................... 0- 1 Chassis Operating Guide .............................. 0- 1 Owner’s InfoCase ......................................... 0- 1 Options and Equipment ................................ 0- 1 Before Driving .............................................. 0- 2 Service and Assistance.................................. 0- 2 Warranty ....................................................... 0- 2 Drinking and Driving...............
TABLE OF CONTENTS Mountain Driving ......................................... 4- 6 Campsite Selection ....................................... 4- 7 Leveling ........................................................ 4- 7 Blocking........................................................ 4- 7 Effects of Prolonged Occupancy .................. 4- 8 Humidity and Condensation ......................... 4- 8 SECTION 5: LP GAS SYSTEM LP Gas Supply ..............................................
TABLE OF CONTENTS Tables and Countertops ................................ 9- 5 Galley Sink .................................................. 9- 6 Range and Refrigerator ................................. 9- 6 Bathroom ...................................................... 9- 6 Doors and Windows...................................... 9- 7 Engine Access............................................... 9- 7 Engine Cover ................................................ 9- 8 Engine Cooling System ..................
INTRODUCTION Congratulations on the purchase of your new Brave motor home, which has been carefully designed, engineered and quality built by Winnebago Industries, Inc. ABOUT THIS MANUAL Please read this operator’s manual completely to understand how everything in your coach works before taking it on its “maiden voyage.” This manual is a guide to safe operation of the features, equipment and controls in this coach.
INTRODUCTION WARRANTY BEFORE DRIVING Before sitting in the driver’s seat, always check around your vehicle to be sure you have proper clearance for maneuvering. If necessary, have a passenger help guide you out of a difficult parking space. Although your coach features automotive conveniences like power steering and power brakes, driving a motor home is different from driving a car.
INTRODUCTION To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in Washington, D.C. area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.
INTRODUCTION VEHICLE CERTIFICATION LABEL This label contains vehicle identification and other important reference information. The vehicle certification label is located on the sidewall to the left of the steering wheel, or on the driver’s door. Never remove or destroy this label. MANUFACTURED BY INCOMPLETE VEHICLE MANUFACTURED BY MOTOR CORP.
INTRODUCTION EXTERIOR FEATURE IDENTIFICATION Actual locations of features depends on coach model and options. NOTE: Some equipment shown may be optional.
SECTION 1 SAFETY PRECAUTIONS Read and understand all instructions and precautions in this manual before operating your new motor home. About Safety Messages Used in This Manual Throughout this manual, certain items are labeled Note, Caution, Warning or Danger. These terms alert you to precautions that may involved damage to your vehicle or a risk to your personal safety. Read and follow them carefully.
SECTION 1 SAFETY PRECAUTIONS heater. They contain carbon monoxide, which is an odorless, colorless and poisonous gas. DRIVING · Do not attempt to adjust the driver’s seat while the vehicle is moving. · Do not adjust tilt steering in a moving vehicle. · Do not operate the cruise control on icy or extremely wet roads, winding roads, in heavy traffic, or in any other traffic situation where a constant speed cannot be maintained. · Use care when accelerating or decelerating on a slippery surface.
SECTION 1 SAFETY PRECAUTIONS WARNING IT IS NOT SAFE TO USE COOKING APPLIANCES FOR COMFORT HEATING Cooking appliances need fresh air for safe operation. Before operation 1. Open overhead vent or turn on exhaust fan. 2. Open window LP gas is present inside the coach. Because LP gas is heavier than air, the detector is located on a cabinet face near the floor of the coach. A green light on the face of the alarm shows when the unit is active. FAILURE TO COMPLY COULD RESULT IN DEATH OR SERIOUS INJURY.
SECTION 1 SAFETY PRECAUTIONS or an LP gas service center to have the problem corrected before using the LP system again. WARNING Never use an open flame to test for gas leaks. When testing for gas line leaks with a soapy water solution, DO NOT use a detergent containing ammonia or chlorine. These substances may generate a chemical reaction causing corrosion to gas lines, resulting in dangerous leak conditions. Power Connection The gas alarm is powered by the coach batteries.
SECTION 1 SAFETY PRECAUTIONS · · · Be sure that all electrical appliances to be used contain 3-prong plugs for proper grounding. Avoid overloading electrical circuits. Replace fuses or circuit breakers with those of the same size and amperage rating only. Never use a higher rated fuse or breaker. Use caution when handling or working near electrical storage batteries. Always remove jewelry and wear protective clothing and eye covering. Avoid creating sparks.
SECTION 1 SAFETY PRECAUTIONS be inspected by a qualified motor home service center. · Each time the vehicle is raised for an oil change. · Whenever a change in the sound of the exhaust system is noticed. · Whenever the exhaust system, underbody or rear of the vehicle is damaged. To allow proper operation of the vehicle’s ventilation system, keep front ventilation inlet grill clear of snow, leaves or other obstructions at all times.
SECTION 1 SAFETY PRECAUTIONS RED LOOP Instructions for removal are also located on a label on the glass for quick reference and for passengers who may not be familiar with the exit. Never removed or destroy this label. WARNING Use emergency window for emergency exit only. Do not test for proper operation. If the cord is released by accident, but the glass remains in place, the cord can be replaced using a blunt instrument, preferably one made of plastic. We suggest you contact your dealer for assistance.
SECTION 1 SAFETY PRECAUTIONS We recommend that you become thoroughly familiar with the operating instructions displayed on the side of the fire extinguisher or in the information supplied in your Motor Home Operations Manual binder. We also recommend that you inspect the fire extinguisher for proper charge at least once a month in accordance with National Fire Protection Association (NFPA) recommendations as stated on the label. If the charge is insufficient, the fire extinguisher must be replaced.
SECTION 2 DRIVING YOUR MOTORHOME (See also Safety Precautions, Section 1 of this manual.) NOTE: See your Ford or Workhorse chassis operator's guide for information on starting the engine, operating the transmission, steering column controls descriptions of instrument gauges and other chassis related information. Some items described in this section may be optional or unavailable on your coach.
SECTION 2 DRIVING YOUR MOTOR HOME 2. Adjust the driver's seat for proper distance from foot pedals and steering wheel to allow for safety and ease in controlling your vehicle. 3. Place front seats in the forward facing position. 4. Be sure to fasten all safety belts to fit you comfortably, but tight enough to obtain the full safety of the belts. 5. Make sure all doors are completely shut and locked. When the doors are shut and locked, there is less chance of the doors flying open in event of an accident.
SECTION 2 DRIVING YOUR MOTOR HOME REPLACEMENT FUEL CAPS To protect gasoline system from excessive pressure or vacuum, or from sudden pressure, replace lost caps with caps of the same design available from your dealer. STARTING AND STOPPING ENGINE Refer to your chassis operating guide for the manufacturer's recommendations on starting and stopping the engine. Brake-Shift Interlock (Workhorse Chassis) Workhorse chassis are equipped with a brakeshift interlock safety feature.
SECTION 2 DRIVING YOUR MOTOR HOME Dead Deadbolt ELECTRIC ENTRANCE STEP The power switch for the electric entrance step is located to the left of the main entry door as you enter the coach. Door Handle Lock Entrance Door Handle - Inside Press lever to separate screen door from main entrance door Screen Door Latch - Inside Lubricate the locks periodically with graphite to maintain good working condition.
SECTION 2 DRIVING YOUR MOTOR HOME Automatic Retraction Feature The coach is equipped with a step retraction feature that retracts the step automatically when the Ignition Switch key is turned to either the On or Start position regardless of whether the Step Power Switch is On or Off. This feature is standard and is installed to prevent injury or damage which may be caused by an extended step when the vehicle is moving. An associated feature is the “Last Out Feature”.
SECTION 2 DRIVING YOUR MOTOR HOME Lift to Slide Lift to Swivel 1 2 SEAT BELTS Passenger Seat - Aisle Side (Recline lever on opposite side) Seats intended for occupancy while the vehicle is in motion are equipped with seat belts for the protection of the driver and passengers. Lap Belts WARNING Do not adjust driver’s seat while vehicle is in motion. After adjusting seat, always use body pressure to make sure slide and swivel locking mechanism have engaged.
SECTION 2 DRIVING YOUR MOTOR HOME To Release: Press button in center of buckle and slide tongue out of buckle. · WARNING Snug and low belt positions are essential. This will ensure that the force exerted by the lap belt in a collision is spread over the strong hip area and not across the abdomen, which could result in serious injury. Only seats equipped with seat belts are to be occupied while vehicle is in motion.
SECTION 2 DRIVING YOUR MOTOR HOME More Info - To read more about power mirrors, see the mirror manufacturer’s information in your Owner InfoCase. MIRRORS Always adjust mirrors for maximum rear visibility before driving off. Make sure the seat is adjusted for proper vehicle control and that you are sitting back squarely into the seat. Power Electric Mirrors The electric mirrors are adjusted using a multi-directional switch located on the dash to the right of the steering column.
SECTION 2 DRIVING YOUR MOTOR HOME REARVIEW TV MONITOR SYSTEM - Optional If your motor home is equipped with this optional system, refer to the Owner InfoCase for specific instructions provided by manufacturer. INSTRUMENT PANEL GAUGES AND CONTROLS The illustrations on the following page showing switches and features provided by Winnebago. See your chassis owner's manual for detailed information on the instrument gauges, steering column controls, brakes, and other chassis original equipment.
SECTION 2 DRIVING YOUR MOTOR HOME INSTRUMENT PANEL Workhorse instruments shown for illustration purpose only. NOTE: Some equipment or controls shown may be optional or unavailable on your model.
SECTION 2 DRIVING YOUR MOTOR HOME MULTI-FUNCTION SIGNAL LEVER The multi-function signal lever controls the turn signals, high/low beam changing, windshield washer, wipers and wiper delay, and the electronic speed control (cruise) on some models.* See your chassis operating guide for complete operating information. *Ford chassis models have the cruise control system integrated into the steering wheel. See your Ford chassis guide for operating instructions.
SECTION 2 DRIVING YOUR MOTOR HOME 3. Turn the fan switch to high (largest dot). 4. Turn on auxiliary (dash) fans if additional air movement is needed B. For reduced defrosting: 1. Turn the temperature control knob to the left to an intermediate warm setting. 2. Adjust the fan speed for desired volume. VENTILATION A. To vent outside air into the vehicle when neither heating or cooling is required. 1. Turn the mode selection knob to VENT. 2.
SECTION 2 DRIVING YOUR MOTOR HOME WARNING Do not use the passenger side front workstation in the extended position while the vehicle is in motion. BEVERAGE TRAY - Storage Space Lifting the hinged top of the beverage tray will reveal room to store several small items. Aux. Batt. Switch (Near entrance door) See also Battery Storage and Maintenance on page 6-7. Passenger Work Station - Optional Pull the workstation top backward toward you until it latches in the fully extended position.
SECTION 2 DRIVING YOUR MOTOR HOME NOTE: When parking at an uneven site, always park the front of the motor home to the downhill side. This allows you to level by raising the front end rather than the rear. Since only the rear wheels are locked while in PARK, raising either one or both of the rear wheels off the ground could allow the vehicle to roll off the jacks. NOTE: The leveling system should be cycled once a month or whenever the vehicle is used, to keep the system in operating condition.
SECTION 2 DRIVING YOUR MOTOR HOME The travel straps are located near the floor at the front and/or rear ends of the slideout room. · To Release: · Pull the strap buckle outward and up to release tension on strap. · Pull a short length of the excess strap back through the buckle to provide sufficient slack. · Unhook the strap end pegs from the mooring bracets on the floor and wall edge. Store straps in location of your choice. (Under the couch is one choice.) .
SECTION 2 DRIVING YOUR MOTOR HOME connects the coach batteries to assist in retracting the room. Rear Slideout Switch (on wall in rear of coach) · Press slideout switch and hold until room is fully extended, then release switch. To Retract SlideOut Room: CAUTION Although there is an awning over the roof of the slideout room, there is a possibility of debris getting onto the roof.
SECTION 2 DRIVING YOUR MOTOR HOME See the HWH Operator’s Manual included in your InfoCase for specific instructions on which valves to open for front or rear slideout rooms and what additional precautions to follow. Winch attachment beneath dinette seat Solenoid Valves Use provided 1/4” nut drive tool to turn nut open 3 TURNS ONLY Slideout Room Solenoid Valve · · · · The hydraulic pump is located between the front frame extensions between the radiator and grille/bumper area.
SECTION 3 IN CASE OF DRIVING EMERGENCY SPARE TIRE STORAGE HAZARD WARNING FLASHER The hazard warning flasher provides additional safety when the vehicle must be stopped on the side of the roadway and presents a possible hazard to other motorists. When the flasher is on, it serves as a warning to the other drivers to approach and overtake your vehicle with caution. WARNING Operating the hazard warning flasher system while moving on the highway is illegal.
SECTION 3 IN CASE OF DRIVING EMERGENCY MOTOR HOME TIRE CHANGING PROCEDURE WARNING We advise you to obtain qualified road service whenever possible. Do not try to change a tire yourself except under emergency conditions, and only by closely following instructions in this manual and the chassis operating guide. If you do satisfactorily complete an emergency tire change, we recommend that you have the wheel nuts checked and properly torque tightened by qualified service personnel as soon as possible.
SECTION 3 IN CASE OF DRIVING EMERGENCY 1. Place jack under jacking point specified in your chassis operating guide. Position jack so it may be operated without placing your body beneath vehicle. 2. Screw jack extension pad out (up) until it touches jacking point surface. 3. Begin jacking until jack is firmly positioned and just begins to bear weight, but do not lift tire off the ground. 4. “Crack” wheel nuts loose with lug wrench, but do not unscrew nuts yet. 5.
SECTION 3 IN CASE OF DRIVING EMERGENCY JUMP STARTING WARNING Automotive batteries produce caustic acid, explosive gases, and electrical current which may cause burns. It is important that the instructions below are followed exactly, or personal injury (particularly to eyes) or property damage may result due to battery explosion, battery acid, or electrical (short circuit) burns. • • • • NEVER smoke near the battery or expose it to open flame or electrical sparks.
SECTION 3 IN CASE OF DRIVING EMERGENCY CONNECTING A BATTERY CHARGER To connect a battery charger, first make sure the engine is switched off. Disconnect the negative lead from the battery. Never disconnect the battery while the engine is running or alternator damage could result. Connect the positive “+” (red) lead of the charger to the positive “+” terminal on the battery. Next, connect the negative “-” (black) lead of the charger to a suitable ground. Finally, plug in or switch on the charger.
SECTION 4 TRAVELING WITH YOUR MOTORHOME (See also SAFETY PRECAUTIONS, Section 1 of this manual.) LOADING THE VEHICLE NOTE: Your motor home’s load capacity is designated by weight, not by volume, so you cannot necessarily use all available space when loading your motor home. When loading the vehicle, distribute the cargo load equally so that you do not exceed either the Front or Rear Gross Axle Weight Rating (GAWR) or the Gross Vehicle Weight Rating (GVWR).
SECTION 4 TRAVELING WITH YOUR MOTOR HOME Weighing: There is typically a scale operator to direct you but the basic routine is to take three separate weights - front axle, whole vehicle, and rear axle. You will first drive only your front wheels onto the scale pad, then drive ahead so that the whole vehicle is on the scale, then finally pull off until just the rear wheels are on the pad.
SECTION 4 TRAVELING WITH YOUR MOTOR HOME axle. For example, on the rear axle, if the left side weighs more than the right, fill the left tires to the pressure required for that weight, then fill the right tires to the same pressure as the left ones. NOTE: The Hitch Load from a Towed Vehicle or carrier box must also be counted on the Rear GAWR and subtracted from the rear axle cargo capacity. roof-mounted luggage carrier designed for this purpose is available from your dealer.
SECTION 4 TRAVELING WITH YOUR MOTOR HOME NOTE: If you tow a car or trailer that weighs over 1,000 lbs., it must be equipped with automatically activated brakes. See the Towing Guidelines for Winnebago Industries motor homes included in your InfoCase for maximum towing capacity and GCWR for your chassis. Before descending a steep or long grade when towing a trailer, reduce speed and shift into a lower gear to control vehicle speed.
SECTION 4 TRAVELING WITH YOUR MOTOR HOME TRAVEL TIPS As you travel around the country in your motor home, you will pick up useful advice from other motor home owners. A number of suggestions can also be obtained by reading articles and regular columns in outdoor and camping magazines. Some magazines and publishing companies print an annual park and campground directory. These can be found at your local news stand or RV supply dealer. Here are a few travel tips to begin with. 1.
SECTION 4 TRAVELING WITH YOUR MOTOR HOME NOTE: We recommend that all motor home occupants become familiar with these safety precautions, and be alert to change in weather. · Be alert, because thunderstorms can form at any time, in any month of the year. Thunderstorms can produce large amounts of rain over a small area in a short time, which may result in a flash flood. Listen frequently to weather reports on the radio for weather and flood conditions.
SECTION 4 TRAVELING WITH YOUR MOTOR HOME shift as needed to climb most hills. If the hill is long or very steep, however, you may need to manually shift to a lower gear to keep the transmission from repeatedly upshifting and downshifting. Select the lowest adequate gear range for the duration of the incline. See your chassis operating guide for more information. CAUTION Observe the engine temperature gauge more frequently than normal.
SECTION 4 TRAVELING WITH YOUR MOTOR HOME These devices are not intended to lift the coach; only to hold it rigid and steady. NOTE: We do not recommend lifting any of the wheels off the ground for leveling. This could allow the coach to roll off the jacks, possibly resulting in damage to the vehicle. EFFECTS OF PROLONGED OCCUPANCY Your motor home was designed primarily for recreational use and short term occupancy.
SECTION 5 LP GAS SYSTEM (See also Safety Precautions, Section 1 of this manual.) LP GAS SUPPLY The LP gas system supplies fuel for the range, water heater, furnace and refrigerator (while in gas mode). When used and handled properly, this system is safe and economical and provides modern living conveniences wherever you travel. · Have the entire LP gas system inspected for possible leaks and missing or damaged parts at each tank filling.
SECTION 5 LP GAS SYSTEM LP Gas Tank Model 30W........................................18 gal.* (23 gal. w.c.) Models32V, 34D & 36M ...................23 gal.* (28 gal. w.c.) *LP Gas tank capacity shown is the usable “full” LP gas capacity, which is 80% of the tank manufacturer’s listed water capacity (w.c. shown in parenthesis). An LP tank must have at least 20% of tank volume free to allow for expansion and proper vaporization of the liquid fuel.
SECTION 5 LP GAS SYSTEM come sooted and lose efficiency by using butane fuel. REFILLING LP TANK There are many LP gas refueling stations located throughout the country. These stations are listed in the telephone directory Yellow Pages under “Gas - Liquified Petroleum - Bottled and Bulk.” Since the LP tank is permanently mounted to the frame, the motor home must be taken to an LP dealership for filling. Do not attempt to remove the LP tank from the vehicle.
SECTION 5 LP GAS SYSTEM REGULATOR The pressure regulator is protected from the elements by a plastic cover which should be left in place at all times. Only your dealer or a qualified LP gas service should remove the regulator cover for adjustments. WARNING Inspect the pressure regulator vent hole periodically for blockage. If any obstruction is apparent, have the regulator serviced by your dealer or a qualified LP gas service center.
SECTION 5 LP GAS SYSTEM WARNING Never use an open flame to test for gas leaks. When testing for gas lines leaks with a soapy water solution, DO NOT use a detergent containing ammonia or chlorine. These substances may generate a chemical reaction causing corrosion to gas lines, resulting in dangerous leak conditions. Temperature 20° F. 10° F. 0° F. -5° F. -10° F. -15° F. -20° F. -44° F. Percentage of BTU’s Available at 0° F.
SECTION 6 ELECTRICAL SYSTEMS (See also Safety Precautions, Section 1 of this manual.) Your motor home is equipped with an electrical system consisting of two separate voltages; a 12-volt DC system and a 110-volt AC system. The 12-volt system consists of two internal power sources, while the 110-volt system is operated from an outside power source or the optional 110-volt generator. All systems operate through a single power converter control center to provide electrical power to the motor home.
SECTION 6 ELECTRICAL SYSTEMS WARNING Do not plug the power cord into an outlet which is not grounded, or adapt the plug to connect to a receptacle for which it is not designed. Be sure that all three prongs of the supply cord are properly plugged into the receptacle. The shoreline cord is designed to ground the electrical system through the receptacle. It is also designed to carry the amperage output of most campground outlets.
SECTION 6 ELECTRICAL SYSTEMS Please read your PowerLine Energy Management System Owner’s Guide for important information on running both front and rear roof air conditioner units at the same time. This guide will also explain how this system operates under several conditions, whether 20-amp or 30-amp connections. POWER CENTER (Converter) The power center changes 110-volt AC current from the auxiliary generator or the shoreline into 12-volt DC current for use by 12-volt equipment in the motor home.
SECTION 6 ELECTRICAL SYSTEMS TEST (Black) Press at least monthly. Should break circuit. Press RESET button to reconnect. RESET (Red) Press to reconnect circuit after monthly testing or ground fault tripping. 110-Volt Circuit Breaker Panel GFCI Outlet (Ground Fault Protector) Further Information Refer to the converter manufacturer’s information provided in your Owner InfoCase for additional information about your power converter system.
SECTION 6 ELECTRICAL SYSTEMS WARNING Careless handling of the generator and electrical components can be fatal. Never touch electrical leads or appliances when your hand are wet, or when standing in water or on wet ground. Do not attempt to repair the generator yourself. Service should be performed by an authorized service center. Do not plug the power cord into the generator receptacle while the generator is running.
SECTION 6 ELECTRICAL SYSTEMS · Press the generator switch Off and hold until the generator engine comes to a complete stop. Approximate Power Requirements of Common Appliances Appliance or Tool Vacuum cleaner Coffee Maker Hair dryer Electric clothes iron Electric blanket Television Electric drill Air conditioner Converter Microwave Oven Approximate Power Consumption (Watts/Amps) 200-500W/1.7-4.3A 550-700W/4.8-6.1A 800-1500W/7.0-13.0A 500-1200W/4.3-10.4A 50-200W/0.4-1.7A 80-100W/0.7A 250-750W/2.2-6.
SECTION 6 ELECTRICAL SYSTEMS The house batteries are “deep-cycle” type batteries specially designed for recreational vehicle use. They will provide longer lasting power than standard automotive batteries, and will withstand the frequent drain-and-recharge cycles that occur under the demanding conditions of a camping outing. The house batteries are automatically charged by the engine alternator while the engine is running.
SECTION 6 ELECTRICAL SYSTEMS WARNING WARNING California Proposition 65 Warning: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the state of California to cause cancer and reproductive harm. Wash hands after handling. Before removing any battery cables or battery, make sure all 12-volt equipment in the motor home is off and the power cord has been disconnected.
SECTION 6 ELECTRICAL SYSTEMS WARNING To prevent wiring damage, it is essential when replacing the cables on the battery, or when using a “booster” battery, that the positive post and the positive cable be attached and the negative post and negative cable be attached. The posts are marked (+) plus and (-) minus. If a “fast charger” is used while battery is in the motor home, disconnect both battery cables before connecting the charger. Never attempt to charge or boost a frozen battery.
SECTION 6 ELECTRICAL SYSTEMS CAUTION The CB radio could become damaged if the CB antenna SWR is not adjusted before operating the CB radio. TRAILER WIRING CONNECTOR Your coach is pre-wired for trailer or car towing lights with a 6-pin socket on the rear bumper. The connector plug is supplied in the coach parts package provided to you by your dealer when you took delivery of the vehicle. The diagram shows proper connection of trailer or tow vehicle wiring to the coach light system.
SECTION 7 PLUMBING SYSTEMS FRESH WATER SYSTEM The fresh water system provides water to the galley sink, shower, bathroom lavatory, toilet and water heater. Water may be supplied by either of two sources: - a water tank located within the motor home, or - any external water source to which the motor home may be connected, known as “city water”. FRESH WATER TANK FILLING PROCEDURES: Always fill the fresh water tank at an approved potable water filling facility or a known purified drinking water source.
SECTION 7 PLUMBING SYSTEMS Fresh Water Tank Capacity Model 30W .................................................78 gal. Model 32V (Ford).......................................80 gal. Model 32V (Workhorse) ........................... 58 gal. Model 34D ................................................. 80 gal. Model 36M ................................................ 70 gal.
SECTION 7 PLUMBING SYSTEMS Initial Water Line Priming 1. Make sure that all water drain valves are closed, including water heater valve. (Refer to Section 10.) 2. Turn water pump switch to “OFF” position. 3. Fill water tank. 4. Open all faucets, hot and cold. 5. Turn on pump switch. 6. Close each faucet as it begins to deliver a steady stream of water (close cold water first). Leave hot water faucets on until they also deliver a steady stream of water.
SECTION 7 PLUMBING SYSTEMS Replacing the water filter cartridge: Replace the filter cartridge when water flow from the purifier faucet is too slow for convenience. · · · Place a container beneath the filter to catch any remaining water during removal. Raise the valve handle near the top of the filter base to block water flow to filter. Twist the filter cartridge counterclockwise about a quarter-turn and pull it down and out of the filter head. 4. Turn on the external water source (faucet).
SECTION 7 PLUMBING SYSTEMS 3. Disconnect the hose from the vehicle and replace the cap on the connection. SHOWER HOSE VACUUM BREAKER After using the shower, you may notice water dripping from the shower faucet assembly. The dripping results when vacuum in the shower hose (after closing the shower faucet) slowly releases and allows water remaining in the hose to drain down. This is a normal function of the shower valve assembly and is not a leak or defect.
SECTION 7 PLUMBING SYSTEMS 8. Rinse sewer hose thoroughly with water and stow. NOTE: We recommend that you dump all holding tanks before traveling to avoid carrying unnecessary weight. Pull last to drain gray tank Pull first to drain black tank DUMPING HOLDING TANKS 1. Remove drain hose from exterior storage compartment. 2. Remove dust cap from drain and connect drain hose. Be sure it is firmly attached. 3. Place the other end of sewer hose into disposal opening. 4.
SECTION 7 PLUMBING SYSTEMS DRAIN DRAIN CLOSE CLOSE LINE-END VALVE IN-LINE VALVE Water Drain Valves (typical) Water Tank Drain Valve In Right Side Rear Cargo Compartment Water Line Drain in right front compartment 7-7
SECTION 7 PLUMBING SYSTEMS TANK CAPACITIES HT1 - Black Water Holding Tank Model 30W (Toilet & Lavatory) ................................................................................................40 gal. Model 32V (Toilet).....................................................................................................................50 gal. Model 34D (Toilet).....................................................................................................................50 gal.
SECTION 7 PLUMBING SYSTEMS WATER SYSTEM DRAIN VALVE LOCATIONS SYSTEM Water Lines: DRAIN VALVE LOCATIONS One (1) valve in the front storage compartment on the passenger side of the coach. Open exterior shower faucet and lay shower head on ground. Also, to drain any water left in the city water line, place the tip of your finger inside the city water connection and gently press the backflow valve (small “button” in center of connector).
SECTION 8 APPLIANCES & INTERIOR FEATURES (See also Safety Precautions, Section 1 of this manual.) NOTE: Because this model is available in several sizes and floor plans, some items described may be optional or unavailable on your coach. A small round bubble level is provided with your refrigerator. Place the bubble level on the bottom surface of the refrigerator and watch the position of the bubble in relation to the circle in top of the level.
SECTION 8 APPLIANCES & INTERIOR FEATURES OPERATING INSTRUCTIONS Norcold Models with Electronic Auto Mode Control Push door handle downward and pull to open refrigerator. (Lift freezer handle upward.) Standard Norcold 9000-Series models with Electric Auto Mode Control The control panel is located between the freezer compartment and fresh food compartment. It contains pressure sensitive touch switches and a digital display.
SECTION 8 APPLIANCES & INTERIOR FEATURES erator is operating in the AUTO LP GAS mode, the refrigerator will switch to AUTO AC operation. If an operating mode is not functional, a diagnostic code will appear and the refrigerator will attempt to operate in a lower power priority source. If a lower power priority source is not available, an alarm will sound and the refrigerator will cease operation. Refer to the Diagnostic Codes and Their Meaning for corrective actions.
SECTION 8 APPLIANCES & INTERIOR FEATURES service center. A different mode of operation may be selected by pressing and holding the MODE button. The refrigerator will not switch to the new operating mode until the MODE button is released. · Food and beverages should also be cold before placing in RV refrigerator. Never put warm or hot items in a cold refrigerator. · Do not pack the refrigerator too full. The refrigerator needs room for cold air to circulate.
SECTION 8 APPLIANCES & INTERIOR FEATURES FROZEN FOOD STORAGE COMPARTMENT Quick frozen soft fruits and ice cream should be placed in the coldest part of the compartment, which is on the top freezer shelf. Frozen vegetables may be stored in any part of the compartment. This compartment is not designed for deep or quick freezing of food. Meat or fish, whether raw or prepared, can be stored in the frozen food storage compartment provided they are precooled first in the refrigerator.
SECTION 8 APPLIANCES & INTERIOR FEATURES WARNING IT IS NOT SAFE TO USE COOKING APPLIANCES FOR COMFORT HEATING Cooking appliances need fresh air for safe operation. Before operation 1. Open overhead vent or turn on exhaust fan. 2. Open window FAILURE TO COMPLY COULD RESULT IN DEATH OR SERIOUS INJURY. To Open: 1. Use a coin to turn the latch knobs to the vertical position as shown. 2. Remove the door from the opening.
SECTION 8 APPLIANCES & INTERIOR FEATURES WARNING Do not turn burner control knob to “On” and allow gas to escape before lighting match. Lighting Oven Pilot NOTE: If range has not been operated for a long period of time, a longer waiting period for ignition of the pilot may be necessary due to air in the gas line. 1. 2. 3. 4. Be sure all valves are in the “OFF” Position. The oven control knob should be in “OFF” position. Turn on main gas supply to range.
SECTION 8 APPLIANCES & INTERIOR FEATURES Hood Fan and Light Switches To turn on the range hood light, simply press the switch labeled “Light”. To operate the range hood fan, press the “Fan Hi/Lo” switch. actually be some water left in the tank. However, when the indicator reads FULL, the tank is actually full. SYSTEMS MONITOR PANEL (Wall Mounted) The System monitor Panel provides a convenient central location for checking the condition of all utility systems in your coach.
SECTION 8 APPLIANCES & INTERIOR FEATURES Battery Charge Meter Push the “Levels Test” button to check the level of charge (voltage) in the 12-volt coach battery. The colored segments (red, yellow and green) will light from the bottom up to the amount of charge the battery contains. * Green - good or adequate charge. * Yellow - marginal charge. * Red - battery needs charging before use. For Electric Operation: Turn on the Water Heater electric element switch.
SECTION 8 APPLIANCES & INTERIOR FEATURES For Quick Recovery Operation (Dual): Turn On both Water Heater switches; the gas one on the monitor panel and the electric one. This will help reheat the water heater tank more quickly than a single source would alone. Use this mode when you are using a larger than normal volume of hot water, for example, when someone is taking a shower and the dishwasher or clothes washer is also being used. Gas Safety Information A. This appliance does not have a pilot light.
SECTION 8 APPLIANCES & INTERIOR FEATURES Manually operate the pressure temperature relief valve at least once a year. *If your water heater is equipped with the optional Motor Aid system, it uses an extension from the engine cooling system to heat water in the water heater while driving. The engine cooling system must also be cold before opening the pressure-temperature relief valve. See “Motor Aid” on following page for more information.
SECTION 8 APPLIANCES & INTERIOR FEATURES Under normal conditions, the entire contents of the water heater can be heated to about 140°F in about two hours or 100 miles of driving. This means you can have hot water at the faucets immediately upon arriving at a site, or even while driving if needed. The motor aid also increases the capacity of the engine cooling system, allowing the engine to run cooler under many conditions.
SECTION 8 APPLIANCES & INTERIOR FEATURES For Further Information Please see the Suburban furnace operating instructions provided in your Owner InfoCase for further information, including operating precautions, and periodic maintenance. HEAT PUMP - Optional Your coach may be optionally equipped with an air source heat pump built into the air conditioning system.
SECTION 8 APPLIANCES & INTERIOR FEATURES See “Air Conditioner Selector Switch” on page 8-11 for instructions on using two roof air units at once, if equipped. See also “Powerline EMS” on page 6-2. Refer to the manufacturer’s information in your InfoCase for complete operating instructions. NOTE: The ducted roof air conditioning system has ceiling registers that can be closed if necessary to force more cool air toward a specific area of the coach or to route cool air away from a specific area.
SECTION 8 APPLIANCES & INTERIOR FEATURES Operation The following chart shows the system functions with the “Heat/Cool” thermostat. Disregard references to heat functions when using the “Cool Only” thermostat in the rear bedroom. TV ANTENNA The TV antenna on your motor home can be easily raised, rotated a full 360° and lowered from inside the vehicle by simply turning a crank or rotating knob.
SECTION 8 APPLIANCES & INTERIOR FEATURES Rotating Antenna - Make sure antenna is in the “UP” position. Pull down on rotating knob until it disengages ceiling plate and rotate for best picture and sound on TV set. SIGNAL AMPLIFIER The amplifier power switch is located on the video selector system panel in the driver’s compartment overhead cabinet. To operate amplifier, turn on power switch.
SECTION 8 APPLIANCES & INTERIOR FEATURES for best picture. Then turn off the amplifier power switch. If the antenna amplifier is working properly, the TV picture will now be degraded (snowy). When you turn the switch back on, the picture should again be sharp. CABLE TV HOOK-UP The cable television connector is located in the shoreline cord compartment. VIDEO SELECTION CENTER The video selection center allows you to switch the antenna, cable TV or VCR signal to any TV set location in the coach.
SECTION 8 APPLIANCES & INTERIOR FEATURES · · The inverter must be switched on to operate. Turn the inverter off when not in use to avoid draining the coach or automotive batteries. EXTERIOR ENTERTAINMENT CENTER The optional exterior entertainment center contains a stereo radio with cassette player or CD player and convenient TV hook-ups for your outside listening or viewing pleasure. Exterior Entertainment Center 2.
SECTION 8 APPLIANCES & INTERIOR FEATURES Rest EasyTM Multi-Position Lounge Optional (If equipped) 4. Arrange dinette cushions to cover bed area. To Revert to Dinette: 1. Replace the table onto the wall support and lower the table leg. 2. Make sure that the table leg is secured into the floor support bracket and the leg brace is locked. To Recline: Press the bottom side of the switch on the front of the armrest. Push the top side to return to upright position.
SECTION 8 APPLIANCES & INTERIOR FEATURES To Extend Pull-Out Footrest Section: Reach through the ‘dip’ opening in the center of the lounge front as shown. Squeeze the latch on the inside of the lower face panel and pull the lower ‘trundle’ section of the lounge outward until fully extended. The gap between the footrest and seat provides ample room to enter and exit the lounge. If desired, however, the footrest section can be pushed against the lounge seat.
SECTION 8 APPLIANCES & INTERIOR FEATURES WARNING To avoid injury to young children, do not allow them to operate the sofa, or to play within the sofa or near the operating mechanism. Hoop Chair Mount The hoop base of lounge chair is mounted to the floor with a clamp as shown. CAUTION The chair must be clamped back into place before driving the coach. FRESH WATER TOILET The clamp knob can be unscrewed and removed to allow you to position the chair as you desire in the living area of the coach.
SECTION 8 APPLIANCES & INTERIOR FEATURES 2. To add more water to the bowl than the normal 2” automatic refill, lift the pedal and hold until desired amount has been added. Release pedal slowly. 4. Remove the water line from the base of the toilet and clean the screen. 5. If the flush valve becomes stiff after extended use, it may be lubricated with a silicone spray.Turn the water pump off and operate flush pedal to drain water from the toilet bowl.
SECTION 8 APPLIANCES & INTERIOR FEATURES SLIDER WINDOWS Lift the latch handle straight out from the window. Grasp the sliding window edge frame and slide the window to the side. Be sure the latch is raised before trying to slide the window closed. To loosen the tension, unwrap the guide cords from the spools one turn at a time until desired tension is achieved. DAY/NIGHTER PLEATED BLINDS Your coach may feature two-stage pleated window blinds that can be used for daytime or nighttime privacy.
SECTION 8 APPLIANCES & INTERIOR FEATURES After replacing the battery, simply place the clock back into the socket with 12 at the 9 o’clock position and rotate upright.
SECTION 9 CARE & MAINTENANCE CAUTION Sealants must be inspected every 6 months and resealed if necessary. ROOF The roof is made of Thermo-Panel materials like the walls and floor. It will support the weight of an average adult should it become necessary to repair the roof or roof mounted components. It is not recommended, however, that very large or heavy objects be carried on the roof while the vehicle is in motion. (See page 4-1 for roof loading specifications.
SECTION 9 CARE & MAINTENANCE Stains and Discolorations Regular cleaning and waxing will help prevent most discolorations and stains; however, please be aware that using caustic, highly alkaline cleaners or any cleaner with ammonia may actually darken your RV’s exterior. If stains or discolorations do appear, they can be removed by gently wet-sanding the discolored area with a fine grit sandpaper and then using an electric or pneumatic buffer and a liberal amount of rubbing compound.
SECTION 9 CARE & MAINTENANCE ing products. Some water-based household cleaning products are not formulated for use on fabrics and may cause excessive shrinkage or fading. Always test any cleaning product on a hidden area of fabric before using on visible areas. For best results, fabric cleaning should be referred to a professional carpet and upholstery cleaner.
SECTION 9 CARE & MAINTENANCE IMPORTANT: Make sure you have selected the right cleaning agent from the list below before your begin the cleaning process. NOTE: In many cases listed in the chart below, repeated steps may be required to fully extract contaminant from material. Items listed with (*) may also be removed through steam extraction method by a professional cleaner or service.
SECTION 9 CARE & MAINTENANCE IMPORTANT: The fabric manufacturer’s recommendeds made above are done in good faith and are based on a history of actual experiences and laboratory evaluations. Foss Manufacturing Company, Inc. and/or its designed distributor does not warrant, either expressed or implied, the effectiveness of the cleaning agents listed and the process for cleaning described above.
SECTION 9 CARE & MAINTENANCE Avoid paint remove or oven cleaner. The solid surface material is also resistant to most chemical substances but exposure to some harsh chemicals and solvents such as these can cause damage that would need professional repair or replacement. If one of these materials does spill or drip onto the counter surface, wipe it up immediately to avoid damage. Technical Assistance.
SECTION 9 CARE & MAINTENANCE DOORS AND WINDOWS Windows may be periodically cleaned with a good quality glass cleaner or mild soap solution using a soft cloth. Use care when removing ice or frost from the windows. Always use a plastic ice scraper, never one made of metal. Use care when removing ice from the mirrors to protect the reflective surfaces. Door locks and hinges should be lubricated periodically with powdered graphite to ensure trouble-free operation and to protect against freeze-up.
SECTION 9 CARE & MAINTENANCE ENGINE COVER · Remove the beverage tray from the engine cover. Remove the drawer to expose the wing nut fasteners that hold the tray to the motor cover. · Insert the supplied hex wrench into the hole in the rear top or edge of the engine cover. The coolant system MUST be refilled or topped up with the same type of coolant as equipped to maintain the special longlife properties. Workhorse chassis use GM Dexcool LLC, which is a bright, pink/orange color.
SECTION 9 CARE & MAINTENANCE SUSPENSION ALIGNMENT AND TIRE BALANCE WINDSHIELD WASHERS AND WIPERS The front suspension and steering system of this vehicle was factory aligned using highly accurate equipment prior to delivery to the dealership. However, we recommend that alignment be checked and adjusted, if necessary, after you have fully loaded the motor home according to your personal needs. Thereafter, the alignment should be periodically inspected to help prevent uneven tire wear.
SECTION 9 CARE & MAINTENANCE Automotive 12-Volt Fuse Block (Under lift-up dash pod) Coach Fuse Panel Lift front of Instrument Pod Automotive Fuse Panel Automotive Fuse Access 9-10 30 30 Good Fuse Bad Fuse
SECTION 10 STORING YOUR MOTOR HOME PREPARING VEHICLE FOR STORAGE Properly preparing your vehicle for storage will lessen the possibility of damage to your vehicle. Prepare the motor home for vacancy just as you would if you were leaving your house for an extended period: · · · · · · Remove all perishables from cabinets and refrigerator Prop refrigerator door open. Turn off LP gas tank. Drain water heater, water tank and holding tank. Drain optional washer/dryer.
SECTION 10 STORING YOUR MOTOR HOME 5. Install the antifreeze diverter plug • Raise the valve handle on the filter base. • Hold the diverter by the support bar as shown and guide it up into the filter base. • Push the diverter up into the head as far as possible and turn it clockwise approximately 90° until it stops. • Lower valve handle to lock the diverter plug in place.
SECTION 10 STORING YOUR MOTOR HOME 8. After water has stopped draining at all faucets and drain valves, connect a “blow-out” plug to the city water connection on the coach. Then use a compressed air hose regulated to 30 psi or less to force air through the system. (A “blow-out” plug can be purchased at any Winnebago or Itasca dealer. P/N 701705-01-000.) City Water Connection 11. Now turn air pressure off and disconnect water purge adapters.
SECTION 10 STORING YOUR MOTOR HOME Water System Winterization Valve Your coach is equipped with a manually operated water line winterization system for your convenience in winterizing fresh water lines. The system features a diverter valve and suction tube in-line between the tank and water pump to draw non-toxic RV water system antifreeze into the water lines. This feature is located near the water pump and drain valves. See page 7-7 or 7-8 for location in your coach.
SECTION 10 STORING YOUR MOTOR HOME 15. Have the vehicle chassis completely serviced and lubricated. Be sure radiator antifreeze protection level is sufficient for the lowest anticipated temperatures. 16. Wash and wax the coach. 17. Inspect all seams and seals around doors, windows, vents, and any other joints. Replace or repair any that are damaged. Sealing materials and compounds can be purchased from your dealer. Badly damaged weather seals may need to be replaced by your dealer. 18.
SECTION 10 STORING YOUR MOTOR HOME NOTE: We do not recommend leaving the shoreline plugged in continuously during storage periods because the batteries can lose electrolytic fluids and become damaged from continuous charging without periodic use. We recommend following regular battery inspection and maintenance, especially in cold weather. See “Battery Maintenance” in Section 6 - Electrical Systems. REMOVAL FROM STORAGE 1. Completely air out the motor home. 2.
INDEX 110-Volt AC System..................................... 6- 1 110-Volt Circuit Breakers............................. 6- 3 110-Volt Receptacles (Outlets)..................... 6- 4 12-Volt DC System....................................... 6- 6 12-Volt House Fuses and Circuit Breakers... 6- 7 A About This Manual ....................................... 0- 1 Air Conditioning ......................................... 2- 12 Air in the LP Gas Tank ................................. 5- 3 Armrest Adjustment.......
INDEX Front Axle Tire Alignment ........................... 4- 1 Front Wheel .................................................. 3- 2 Fuel and LP Gas............................................ 1- 2 Fuel Selection ............................................... 2- 2 G Galley Sink .................................................. 9- 6 Gas/Electric Water Heater ............................ 8- 9 Gasoline Fuel Fill.......................................... 2- 2 Gelcoat Fiberglass Finish ........................
INDEX Seat Belt Care and Cleaning ......................... 2- 7 Seat Belts ...................................................... 2- 6 Seats .............................................................. 2- 5 Selecting LP Fuel Types ............................... 5- 2 Service and Assistance.................................. 0- 2 Severe Weather Information ......................... 4- 5 Shower Hose Vacuum Breaker..................... 7- 5 Signal Amplifier .........................................
IMPORTANT SERIAL NUMBERS Motor Home (Coach): Year _________ Model ___________________ Serial _____________ Chassis: Make ___________________ Serial (VIN) ______________ Roof Air Conditioner: Furnace: Water Heater: Power Converter: 110-Volt Generator: Range: Microwave Oven: Refrigerator: Television: Video Cassette Player: Brand ___________ Brand ___________ Brand ___________ Brand ___________ Brand ___________ Brand ___________ Brand ___________ Brand ___________ Brand ___________ Brand ___________ Model
MAINTENANCE RECORD Date Odometer Mileage Description of Service Cost
FUEL & OIL RECORD Date Odometer Mileage Fuel Gal. Oil Qts. MPG Cost Date Odometer Mileage Fuel Gals. Oil Qts.
FUEL & OIL RECORD Date Odometer Mileage Fuel Gal. Oil Qts. MPG Cost Date Odometer Mileage Fuel Gals. Oil Qts.
