IC70-series Panel PC Intel® i5/i7 800/1066 MHz Mini-ITX SBC, High Performance Design with Intel HM55 Platform, CRT/LCD/TV and versatile expansions. User Guide Version 1.
FCC Statement This device complies with part 15 FCC rules. Operation is subject to the following two conditions： This device may not cause harmful interference. This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class "a" digital device, pursuant to part 15 of the FCC rules.
Copyright Notice ALL RIGHTS RESERVED. No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer. Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners.
Check List Before using this Panel PC, please make sure that all the items listed below are present in your package 1 x IC70 series Panel PC 1 x IC70 series Panel PC User Guide 1 x IC70 SBC User Manual 1 x Power adapter 1 x CD-ROM disc with Driver Utility and User's Manual Make sure that all of the items listed above are present. Do not attempt to apply power to the system if there is damage to any of its components.
Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card. Modern electronic devices are very sensitive to static electric charges.
Safety and Warranty 1. 2. 3. Please read these safety instructions carefully. Please keep this user's manual for later reference. Please disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Revision History Version Date 1.0 2011.08.
Contents CHAPTER 1 GENERAL INFORMATION.........................................................................................1 1-1 Introduction................................................................................................. 1 1-2 IC70 series Panel PC System Specifications ................................................ 2 1-3 LCD Selection Guide................................................................................... 3 CHAPTER 2 GETTING STARTED..................................
Chapter 1 GENERAL INFORMATION 1-1 Introduction The IC70 series Panel PC is high performance PC with Intel® HM55 chipset which combines with a TFT LCD Panel. The Intel® i5/i7 high performance Processor delivers the most performance per watt available in the market. The Panel PC is designed to satisfy most of the applications in the industrial market, such as POS, KIOSK, Industrial Automation, HMI and Programmable Control System.
1-2 IC70 series Panel PC System Specifications Form Factor Mini-ITX CPU Intel® i5/i7 800/1066 MHz Processor Chipset HM55 Memory DDR3 1066/800MHz SO-DIMM x 2 Slot (MAX 8GB) BIOS AMI UEFI BIOS Graphic Controller Integrated Gfx Gen5.
1-3 LCD Selection Guide The IC70 series Panel PCs support form 10.4-inch to 15-inch TFT Panel w/ touchscreen function, please refer the below: Item Size Resolution (Recommended) Display Color 15” R15IC7T-XXC3 1024 x 768 16.2M colors (RGB 8-bits). 15” R15IC7T-XXA1 1024 x 768 16.2M colors (RGB 8-bits). 17” R17IC7T-XXM1 1280 x 1024 16.7M (6bits+FRC) 19” R19IC7T-XXM1 1280 x 1024 16.7M colors (8bits) 20.1” R20IC7T-XXA2 1600 x 1200 16.7M colors (8bits) 21.5” W22IC7T-XXA1 1920 x 1080 16.
Chapter 2 Getting Started 2-1 Input / Output Devices The following figure shows the I/O arrangement of the Panel PC. The backside of the chassis contains most of the connectors. 5 1 8 4 6 7 3 2 1 Power On / Off / Reset Power on/off and Reset the power on your computer. 2 Audio Audio Jack for Audio (Line-Out, Line-In, Mic-in) 3 USB port USB-compatible devices can be plugged directly into the USB 2.0 port.
2-2 Starting the Panel PC& O/S Installation 1. Connect the power to AC/DC adapter, and connect the power cord to the AC outlet. 2. 3. Press the power on switch to start the Panel PC. Press “DEL” to enter the CMOS setting and check the BIOS setup. 4. You may install your own O/S if it is not installed. When installing O/S for this Panel PC, please follow the steps and use external equipment as Keyboard and Mouse.
Chapter 3 Touch Driver Installation 3-1 Introduction The PPC supports three kinds of Touch Panel Solutions: ELO AccuTouch touchscreen, Premier Touch system. Both of the touchscreen system consists of a touchscreen and an electronic touchscreen controller. The IC70 series Panel PC’s touch device is used RS232 interface touch controller card via the COM2 port inside Panel PC. When the touch driver installed either for ELO or Premier Touch systems, it will detect COM2 port automatically.
3-2 The ELO AccuTouch Driver Installation ELO AccuTouch driver software provides a consistent software interface among all ELO AccuTouch touch screens and controllers. Go to http://www.elotouch.com/Support/dnld.asp for a complete list of available drivers. For Driver Installation, please install the “ELO Touch System Touch Tools CD” for Windows XP, Windows 2000, Windows Me, Windows 98, Windows 95, Windows NT, Windows CE 2.x, 3.0, 4.x, Windows XP Embedded, Windows 3.1, DOS, OS/2 Warp, and Apple Macintosh.
3-2-1 Configuration Utility After finishing the installation, please follow the steps to test the configuration utility. Step.1 Enter “My Computer”, click the “Elo touchscreen” shortcut function. Step.2 Click “Align” function key to go to next step.
Step.3 Correct 4 point locations on screen with the Panel PC. Screen display as follows. Step.4 Touch the “yes” function if the cursor follows your finger and finish the utility test.
3-3 The Premier Touch Driver Installation TouchKit is the Premier Touch software, which contains drivers of the touch panel controllers for the specified communication connectors, RS232, PS/2 and USB, and the other two utilities. The two utilities are as follows: Touch Tray support This is utility for emulating the right and left button of mouse through controlling touch panel. Users can toggle between right or left mouse buttons by this utility.
3-3-1 Configuration Utility After finishing the installation, please follow the steps to test the configuration utility. Step.1 Click the “TouchKit” shortcut function in the desktop. Step.2 Enter “General” function and choose the language you need. Then go to next step.
Step.3 Correct 4 point locations on screen with the Panel. Screen display as follows Step.4 Play “Yes” to continue if 4 points calibration test is fine and finish the test.
Chapter 4 IC70 series Panel PC Mounting Guide The Panel PC is suitable for most of the industrial/commercial application, by any kind of mounting approach. Three main mounting approaches, such as Panel Mount / Chassis / Open Frame, are very easy for user to install the Panel PC. As the pictures guided: 4-1 Open Frame Panel PC: -Panel is aligned with the same height of the front of open frame metal housing -Customers can fix our Panel PC with their own front bezel.
Panel PC size 15” 17” 19” VESA Mount Dimension 75 x 75 mm / 100 x 100 mm 75 x 75 mm / 100 x 100 mm 75 x 75 mm / 100 x 100 mm 14 IC70 series Panel PC User Guide
4-2 5mm Panel Mount Panel PC: -Panel is aligned with the same height of the front of open frame metal housing. -Touch/Glass is higher than Open frame metal housing. -Customers can fix our Panel PC with their fixture (max.12mm) -VESA mount holes are also available for mounting from back side.
16 IC70 series Panel PC User Guide
4-3 10mm IP65 Panel PC -Touch/Glass is aligned with the same height of the front of open frame metal housing -Customers can fix our Panel PC with their fixture by M3 screws. -VESA mount holes are also available for mounting from back side.
18 IC70 series Panel PC User Guide
4-4 Chassis Panel PC Fix the Panel PC with four screws (standard VESA), and fasten to the wall with other four screws.
