Range Hoods Installation Instructions, Maintenance, Use and Warranty INSTRUCTIONS FOR MODELS: WP119 1
IMPORTANT SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, READ THE FOLLOWING: ➢ ➢ ➢ ➢ ➢ ➢ ➢ Use this unit only in the manner intended by the manufacturer. If you have questions, please contact the manufacturer. Before servicing or cleaning the unit, switch the power off and turn power off at the electrical panel and lock the service panel. This will prevent the power from accidentally turning on.
LOCATION REQUIREMENTS IMPORTANT: Observe all governing codes and ordinances. Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. Canopy hood's location should be away from strong draft areas, such as windows, doors, and strong heating vents. Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.
VENTILATION REQUIREMENTS General requirements ➢ ➢ ➢ ➢ Range hoods must be ventilated to the outdoors, except for non-vented (recirculating) installations. Do not ventilate the range hood into an attic or other enclosed areas. Do not use 4” (10.2 cm) laundry-type wall caps. The length of the range hood and the number of elbows should be kept to a minimum to provide maximum performance. For the most efficient and quiet operation ➢ ➢ ➢ ➢ ➢ ➢ ➢ Use no more than three 90-degree elbow.
Rear Discharge A 90-degree elbow may be installed immediately above the hood. Calculating Vent System Length To calculate the length of the system you need, add the equivalent feet (meters) for all vent pieces used in the system. INSTALLATION DIMENSION RECOMMENDATIONS For the WP119 model wall mount range hoods: A. Standard counter top from floor to top of counter is 36 inches B. From the bottom of the range hood, with grease tray installed, minimum of 14 inches and a maximum of 18 inches from cooktop.
Exhibit A INSTALLATION INSTRUCTIONS for Wall Mount Range Hood Parts supplied A. B. C. D. E. F. G. H. I. J. K. L. Range Hood Power Cord (attached to range hood) 6” or 8” round vent air flap depending on model. (attached to range hood on top of unit) Stainless Steel Baffle Filters (Preinstalled to the bottom of the range hood) Duct bracket: 1 bracket w/2 screws attached (1) 6” or 8” round flexible duct exhaust hose, depending on model (2) Stainless Steel Ducts (inner and outer) (1) Grease collection tray.
C A B E D F G H I J K L 7
Parts not supplied ➢ ➢ ➢ ➢ Fasteners for range hood mounting bracket (I) Duct tape Preinstalled ventilation system and ductwork Preinstalled outside duct cap or weatherproofing Installing the range hood This installation is for mounting the product to a wall. Ensure your wall has the proper support to hold the range hood weight.
6. 7. Secure the range hood mounting bracket (J) into wall studs or a wooden cross support system with the two mounting clips on the bracket facing upward towards the ceiling. Please refer to the dimensions on page 5 to determine location of the range hood mounting bracket. It is recommended that a professional installer be used for installation. These two mounting clips, on the bracket (I) will hold the range hood once mounted.
OPERATING INSTRUCTIONS Note: There are different operating instructions based on the control panel for your model. Please choose the operating instruction for your unit. Powering on/off and Settings: Lamp ➢ ➢ ➢ ➢ ➢ Timer Minus Clock Plus Fan Power/Standby Lamp: Press the lamp display one time to activate the light, press the lamp display again to deactivate it. Power/Standby: When the range hood is in the “original” state, touch this button. It will enter the standby mode.
Powering on/off and Settings: Lamp ➢ ➢ ➢ ➢ ➢ Timer Clock Fan Lamp: Press the lamp display one time to activate the light, press the lamp display again to deactivate it. Power/Standby: When the range hood is in the “original” state, touch this button. It will enter the standby mode. Setting the clock: When the range hood is on “Standby” Mode, press and hold the timer button for 3 seconds. The range hood will then enter the time setting state; the display screen will show numbers.
➢ ➢ o 4=Low If you choose a new speed by pressing a different button, the new fan speed will replace the old fan speed. To turn fan off push button 5 To operate light on/off push button 1 (Note: The fan and light operate independently of each other) Powering on/off and Settings: Lamp Timer Minus ➢ ➢ ➢ ➢ ➢ Plus Fan Power/Standby Lamp: Press the lamp display one time to activate the light, press the lamp display again to deactivate it.
Powering on/off and Settings: Timer Lamp Fan Fan Speed ➢ ➢ ➢ ➢ ➢ Clock Power/Standby Lamp: Press the lamp display one time to activate the light, press the lamp display again to deactivate it. Power/Standby: When the range hood is in the “original” state, touch this button. It will enter the standby mode. Setting the clock: When the range hood is on “Standby” Mode, press and hold the timer button for 3 seconds.
CARE and MAINTENANCE Cleaning Self-Cleaning function This Winflo premium range hood comes with a self-cleaning function. Operation instructions: 1. 2. Remove the grease tray (I) from the range hood. Insert the Water reservoir for self-cleaning function (K). The reservoir will slide underneath the bottom of the range hood. Underneath the range hood there is a Exterior Surfaces To avoid damage to the exterior surface, do not use steel wool or soap filled scouring pads. Always wipe dry to avoid water marks.
• Do not use chlorine bleach. Grease/Baffle Filter • • • • • • • Remove the filter by pulling the spring release handle and then pulling down the filter. Wash filters as needed in dishwasher or hot detergent solution (low temperature, short cycle). If your model has a grease tray, please remove, drain and clean periodically. Make sure filters are completely dry before putting back into range hood. Reinstall the filter by making sure the spring release handles are toward the front.
LIMITED WARRANTY This warranty extends to the original purchaser only. This warranty is not transferable, between homes or owners and is only applicable to residential use. Winslyn Industries, LLC provides a 3-year limited parts warranty for all range hoods. Under this warranty, you (the customer), is entitled to replacement parts at no cost to repair and restore functionality if any part of the product were to fail. No labor is provided.
Winslyn Industries, LLC 1232 Hardt Circle Bartlett, Illinois 60103 Email: support@winslyn.
