WINEGARD ® Movin’ View TM Digital Satellite Mobile Antenna for Two Receivers for Use While Stationary Models MV3500A (White Dome) MV3535A (Black Dome) Made in the U.S.A. U.S. Patent Nos. 6,023,247; 6,188,300 dy HD-Reeagard HD Win e with the Interfac Satellite rately) pa (sold se Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000 319/754-0600 • FAX 319/754-0787 • www.winegard.com Printed in U.S.A.
Introduction/How Does Digital Satellite TV Work? About this manual —We hope this manual will provide clear instructions to install and operate MV3500A. Two symbols have been used — Indicates suggestions to make Indicates caution should be taken! processes easier for you. ! Introduction Congratulations! You have purchased one of Winegard’s latest developments in the mobile satellite reception product line —the Movin’ ViewTM.
Quick Reference Guide NOTICE! ® This model is PRESET for DIRECTV receivers. If you have a DISH Network® or ExpressVu® (Canada) receiver, you must change the numbered switches inside the dome. TO CHANGE SWITCHES INSIDE DOME — 1. Remove screws holding dome to base and remove dome. Place dome in safe spot to avoid damage. Switches will be set at 101° for DIRECTV®. You may be changing these switches.
To toggle between satellites when subscribing to multi-satellite programming— The MV3500A will toggle between the primary and seconday satellites for either DISH Network or DIRECTV. Both have programming on more than one satelite. When a channel is selected on the remote control and is not on the satellite currently selected, the unit will automatically toggle to the correct satellite. 5. Your system is now set up to toggle between satellites.
Parts Included • Tools Needed • How to Unpack PARTS INCLUDED: All required screws, washers, bolts, and nylocks 1 base with electronics, dish, dual LNBF 30’ Coax Cable 30’ Power/Data Cable bundle 1 Radome 1 Power switch 1 Wall plate (white) 1 Surface mount box 1 Cable entry plate 4 Base feet large yellow flag connector 2 small red flag connectors TOOLS NEEDED FOR UNPACKING & INSTALLATION: Level Drill w/3/4” bit 1-1/4” hole saw (if mounting switch in wall) Phillips screw driver #2 3/8” Open end wrench 1/2”
Installation Diagram SIDES OF CONTROL UNIT MUST BE PARALLEL TO THE CENTER LINE OF THE VEHICLE AND FACE FRONT OF VEHICLE. OR REAR OF VEHICLE. CENTER LINE OF THE VEHICLE Control Unit LNBF ELEVATION MOTOR Used for Second Receiver (Not Included) Model MV3500A GPS ANTENNA (RoadTrip SDi In-Motion models ONLY) (#1 represents Switch DOWN; #0 represents Switch up) Sat. Rcvr. ....................... Switch Set Position .... 1. 2 3 4 5 6 7 8 DISH NETWORK........................ . ...... 0.... 0..
Installation Installing unit on roof of vehicle — 3. After selecting location for unit (see number 2), put the unit on the centerline of the vehicle. 4. Position base so that cables exit toward the rear of the vehicle. Electronics box should be parallel to the centerline of the vehicle. ! Install in DRY conditions only! IMPORTANT! Do not install this system in the rain, or under any wet conditions. Moisture may affect electronics and void your warranty! 1.
Installation Cable entry installation — INSTALLING THE POWER SWITCH 1. Decide the best location for the cables to enter the vehicle, and the location of the power switch and receiver (see “Installing the switch and receiver”on pages 9 and 10). Drill a 1/2” hole in the roof, push wires inside. Make proper connections. You must have filtered +12 VDC power source. 2. If installing a second receiver, route second coax cable (not supplied) through empty Heyco into base.
Installation • Wiring Connecting the receiver — Initializing & replacing the dome after connecting the receiver(s) — 1. Connect the coax cable from the MV3500A to the “SATELLITE IN” on the receiver. 1. Be sure that switch settings have been made according to your service provider. See page 3. 2. Be sure vehicle is in a location free of all obstructions and with a clear view of the satellite. 3. Power up unit, turn on receiver. Verify that the correct satellite is found.
Troubleshooting PROBLEM SOLUTION The MV3500A does not attempt to find a satellite or it never moves. 1. Check your Power switch to verify that it is in the ON position. The dish never stops on any of the signals that it sees. 1. Make sure that your receiver is set up correctly. 2. Check +12 V wires at unit to verify power. Check fuse on electronics. For DISH Network, the check switch should read either “Unknown” or “SW42”. For DirecTV the receiver should be set for a Two Satellite Oval Dish.
Specifications & Warranty Features and specifications • One button operation. • Dome UV protected. • Depending on receiver type, you can access satellites 119°, 110°, 101° or 92°. • Compact size — 32” diameter, 15-3/4” height Weight of unit - 28 lbs. Shipping weight - 41 lbs. • No user input required. • No data port required for DISH Network®, DIRECTV® or ExpressVu. • Operating temperature -13°F to +140°F • Elevation range 18° to 74.
Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601 • 319/754-0600 Fax 319/754-0787 • www.winegard.com Printed in U.S.A.
