Wine Cellar Cooling Systems 酒卫酒窖冷却系统 Humidifier 加湿机 Installation, Operation and Maintenance Guide 50 Hz Application 安装，操作及维修指南 50 赫兹专用 Manufactured by: www.wineguardian.com Syracuse, NY www.airinnovations.com 制造商 美国空气创新公司 酒卫保留权利，恕不另行通知，可自行决定更改此文件。 如需酒卫使用手册和其他最新文本请访问我们的网站。 Wine Guardian 是空气创新公司的注册商标（注册号 2972262） 2010 年 12 月版 Wine Guardian reserves the right, without notice, to make changes to this document at its sole discretion.
TABLE OF CONTENTS INTRODUCTION 导言 ................................................................................ 1 Receiving, Unpacking and Inspection 接受，拆包和检查 ............................................ 1 General Description 总体描述 ..................................................................... 2 Size and Capacity 尺寸大小和制湿量 .......................................................................... 4 OVERVIEW ...........................................................................................
INTRODUCTION 导言 Dear Customer: Congratulations and thank you for purchasing a Wine Guardian® Humidifier. We believe it to be the best wine cellar humidifier on the market and hope that you will agree. This guide is intended to help the installer and owner of the Wine Guardian Humidifier to properly install and maintain the equipment. In order to ensure optimal performance, the equipment should be installed properly and have proper care and maintenance.
装，不与冷却装置接触。基本或集成加湿机是拟安装在酒卫冷却装置（参见图 6.0）主机 上，并带有接口配板。 在收到并打开包装之前，检查包装箱是否明显的包装损坏或处理不当的地方。写下任何关 于提单签署前明显损坏和差异的地方。 查找装箱单和检查内容的完整性。请确保它是正确的机型，包括工厂选项和配件。 酒卫加湿机湿度调节器用电线接入酒卫主机接线板终端，并带有排水管 线，需要用管道 接入地漏排水口或冷凝排水泵。检查所有的任何损坏或在运输途中造成的松动部件标设 备。立即将所有可见的或隐蔽的损坏文件报告给承运人。 NOTE: If this procedure is not followed, the shipping company may reject the claim and the consignee may suffer the loss. Do not return the shipment to the factory.
line to restrict the flow of water but a throttling valve may be needed to keep too much water from going to the pad. All that is needed is a steady dripping of water out of the drain to ensure adequate wetting and flushing of the pad media. Excess water does not negatively impact the humidifier’s operation but neither does it contribute to more humidification. The drain volume is too much for just a bucket.
湿机将自动关闭。建议的酒窖设定值是 55％。这个湿度值足以防止瓶塞干燥，也足够 低，以防止窖内产生霉菌。加湿机启动后水电磁水阀门打开，风扇开启。如果加湿机与酒 卫冷却主机集成组装并连接，湿度调节器也控制主风机的空气流通。 CAUTION 警告 CAREFULLY FOLLOW THE INSTALLATION INSTRUCTIONS INCLUDED WITH THE HUMIDIFIER. REFER TO THE MANUFACTURER’S INSTRUCTIONS CONTAINED IN THE BOX FOR THE HUMIDISTAT. WE RECOMMEND YOU KEEP THESE INSTRUCTIONS IN A FOLDER ALONG WITH THIS GUIDE FOR FUTURE REFERENCE.
Factory tested – all Wine Guardian Humidifiers are run in the factory and tested for operational performance prior to shipment. Fan – turns “On” and “Off” on signal from the humidistat when humidity in the cellar is required. The fan draws air across the evaporative drip pad to absorb moisture. Grille – for freestanding applications only. Used to separate the inlet air from the discharge air. Orifice – small fitting with a very small hole in the center to restrict the flow of water.
Dimensional Drawing 尺寸图 （所有尺寸以 MM 为单位） (All dimensions in Metric MM) 303m m 256m m 351mm 12.7mm m 151mm 327mm 256 mm Figure 1.
Component Parts Cutaway Drawing 构件切角图 Figure 2.
Wiring Diagram 接线图 Figure 3.
Safety 安全 The Wine Guardian Humidifier uses only 24-volt power. However, that power comes from a transformer, which uses 120-volt power. Therefore, before servicing the humidifier, be sure to disconnect the main power to the cooling unit or to the humidifier. The water supply to the humidifier may be hot. Turn off the humidifier and allow the water to cool before servicing the humidifier.
Pre-Installation Check To check for any possible non-visible shipping damage, you may wish to test the unit before actually installing it. To do so, remove the unit from its packaging and set it on any sturdy level surface. If a freestanding unit, plug in the unit. If the unit is to be mounted into a cooling unit, you need to wire the humidifier to the cooling unit and the cooling unit must be turned on. Then turn on the rocker switch on top of the humidifier. The switch light should come on.
Free Standing Installation with Stand-Alone Model 独立型自由站立安装 Figure 4.0 Stand-Alone Installation 1) Mount the face grille onto the humidifier box so that the separation plate slides in on top of the fan and between the insulation on the sides. The two metal tabs (top and bottom) should slide in between the insulation and the metal wall. Install two screws (top and bottom) into the metal tabs to secure the grille in place. 2) Determine where unit will be mounted. a.
独立安装 1）安装加湿机 格栅框，分离板应从顶部插入风扇上端和绝缘层之间。两个金属片（顶部 和底部）用以固定插入绝缘层和金属墙的分离板。安装两个螺丝穿过金属片（顶部和底 部）固定格栅。 2）确定机器安装位置。 a 如果是挂墙式安装，使用提供的金属支架。将支架固定到墙上，顶部小洞，底部大 洞。装入加湿机时，注意底部的排水管。使用提供的螺丝固定加湿机顶部。 b 如果用货架安装，货架上应钻一个 1 英寸 直径的小孔，加湿机底部排水管就此穿 过。 c 如果是穿墙式安装，打孔大小应以设备外形尺寸为准。注意允许排水管线，进水管 和法兰盘的空间。机器插入后应固定（法兰盘用于前端）。用保温绝缘材料填补加湿机与 墙体框架 之间空间漏洞。 NOTE: In all mounting arrangements make sure the humidifier is level and plumb in all directions. 3) Install a 6.
Stand-Alone Humidifier Mounting (Typical) 独立加湿机安装（典型） Figure 5.0 Wine Guardian-Mounted (Integrated Installation) 酒卫安装(集成安装) NOTE: Integrated humidifiers can be mounted in either of the two side openings of the cooling unit on the cooling or evaporator end only. Do not mount the humidifier on the condenser end of the unit. If a duct connection is in that position, move the duct connection to the top or other side.
在侧面开口处。接口配板允许将加湿机安装在任一向前或向后的位置，只需旋转接口配板 180 度即可。 3) Install a 12.70 mm flexible drain line from the bottom of the humidifier to an open drain or connect into the drain line from the cooling unit. 加湿机底部，安装一个 12.70 毫米灵活排水管线，接到地面的排水口，或用管线连接 到冷却装置的排水管。 4) Install a 6.35 mm hot water line from the water supply into the opening on the top of the humidifier. A shut off valve (not provided) is recommended to isolate the humidifier from the water system when needed. 加湿机顶部应安装一个 6.
电线重新安装后，在电线上做一个轻微的拉回测试。如果需要额外的布线，拼接到工厂提 供的线路上。为了保持连续性， 尽量用同一颜色的电线，并用绝缘胶带使每根电线分 开。 CAUTION 警告 BE SURE THAT EACH COLORED WIRE IS IN ITS PROPER COLOR-CODED SLOT ON THE TERMINAL STRIP AND THAT THEY ARE TIGHT. MIS-CONNECTED HUMIDISTAT WIRING MAY RESULT IN IMPROPER OPERATION AND/OR CAUSE DAMAGE TO THE UNIT AND HUMIDISTAT. 电线颜色与接线板终端的颜色必须正确匹配，各终端线路接紧。接错的线路可能导致操作 不正常 和/或 损害机器和湿度调节器。 1）Mount the humidistat on a solid surface away from doors, corners, air outlets or other drafty or heat generating equipment.
Start-Up and Operation 启动和运行 Now that the installation is complete, it’s time to start the unit. 1) Check to make sure all connections are secure. 2) Turn on the cooling unit if so mounted. 3) Turn on the rocker switch on the top of the humidifier. 4) Test the operations by setting the humidistat above the room condition. The humidifier should come on, the water solenoid should open, and water should flow. It may take a few minutes for water to appear in the drain line.
湿度调节器广泛的应用在制造商的文献中，包含的信息可能不是特别针对您的酒窖中的应 用。请参阅制造商的湿度调节器说明书。我们建议您按照酒卫的湿度调节器的指示， 把 这些说明书于酒卫操作和维护手册保留统一的文件夹里，供未来参考。 1) Disregard the wiring diagrams shown within the manufacturer’s instructions. Refer to the wiring diagram shown in this guide on page 8. The remote outdoor sensor is not required for wine cellar applications and should not be programmed for use.
Inspection and Start-Up Checklist 检查和启动检查清单 Handling and Installation 搬运和安装 1) 2) 3) 4) 5) 6) 7) 8) Mount unit on solid, level surface. Allow sufficient space for access to unit and accessories. Provide proper electrical service. Provide hot water to humidifier. Install drain line with proper pitch. Install ductwork, fittings and grilles properly. Insulate all cold duct surfaces. Do not obstruct airflow.
Maintenance 保养 CAUTION 警告 BEFORE PERFORMING MAINTENANCE ON THE UNIT, READ AND UNDERSTAND THE SAFETY INFORMATION CONTAINED IN THIS GUIDE. 维护机器前，请阅读和理解安全指南。 The Wine Guardian Humidifier is designed for minimal maintenance. Never oil any part of the humidifier. Always disconnect the electrical power to the humidifier and the cooling unit if used. 酒卫加湿机的设计只需极少的维护。任何部分都不要上油。维护机器前，请务必切断加 湿机和冷却主机的电源。 A regular maintenance program prolongs the life of the humidifier and maintains the humidity in the cellar.
每年 –在每月维修的基础上： √清洁加湿机，如果需要更换加湿机分布垫 （见以下步骤） √腐蚀或生锈检查 -清洁和油漆 √检查是否有任何松动的绝热材料，紧固件，垫片或连接口 √检查线路连接和电源线的完整性 √检查加湿机风扇和电磁水阀的运行 √检查供水管瞄准到分布托盘中间位置的两个小孔。 Cleaning the Humidifier and Replacement of Evaporative Drip Pad 清洁加湿器，蒸发滴灌垫更换 Figure 7.0 CAUTION 警告 BEFORE STARTING WORK, BE SURE THE POWER TO THE WINE GUARDIAN COOLING UNIT AND HUMIDIFIER ARE TURNED OFF. MAKE SURE THE POWER CORD IS DISCONNECTED FROM THE POWER SOURCE.
4) Pull one side of the humidifier pad assembly frame toward you and remove the distribution tray from the frame. 拉加湿机分布垫 装配架一侧，从架上移开分布托盘。 5) Slide the humidifier evaporator pad out of its frame. Clean the frame by twisting and flexing it to loosen any calcium deposits, or use a putty knife. 分布垫即可滑出塑料架。轻轻扭曲塑料架来松动钙质沉积物，或使用油灰刀清理。 6) Carefully scrape any mineral deposits from the tray and frame. Be sure the frame drain hole has nothing blocking it.
Humidifier Water Line Maintenance (See Figure 8.0) 加湿机进水管线维修（见图 8.0） 1) Repeat steps 1 and 2 above. 重复以上 1 和 2 步骤。 2) Disconnect the water line at the inlet to the solenoid valve. 断开电磁阀门的进水口水管。 3) Remove the in-line strainer from inside the inlet fitting by using a small flat-bladed screwdriver. Do not insert anything into the strainer that a sharp end on it as it might penetrate the strainer and render it useless.
Water Line Maintenance Detail 进水管道维修详细 Figure 8.
Directory of Terms 缩写语言索引 Ambient Air – The surrounding area outside the cellar such as a room, basement, garage or outdoors. 环境空气 - 酒窖外的周围，如一个房间，地下室，车库或室外区域 CLS – Cubic litres per second. A unit of measurement for the amount of air handled by the fan. CLS-立方升每秒。一种用于空气由风机处理量的测量单位。 Condensate / Condensation – The water formed out of the air when it is cooled below a certain temperature (called dew point). Often referred to as “sweating” on pipes and cold surfaces.
Grille or Diffuser – Inlet or outlet plates to direct the airflow or protect the inside of the unit. 格栅或扩散片 – 空气进口或出口引导板，或机器的保护板。 Heat Gain / Loss – The amount of cooling or heating expressed in watts transferred between the wine cellar and the ambient space. The Wine Guardian must offset this load. 热增益/损失 - 酒窖和环境空间的冷却或加热的总额用瓦表示。酒卫系统必须抵消这种 负荷。 Inlet Air – The air entering the evaporator and condenser sections of the Wine Guardian unit.
