WALL HOOD www.windsterhood.
Table of contents A. Important safety Instructions ---------------------------- P.1 B. Safety notes ------------------------------------------------------ P.3 C. Tools and materials required ---------------------------------- P.6 D. L E D l i g h t r e p l a c e m e n t E. Accessories - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P.6 ------------------------------------------------- P.7 F. Troubleshooting -------------------------------------------------- P.7 G.
A. IMPORTANT SAFETY INSTRUCTIONS Read and Save These Instructions 1. Make sure the power is off before installing, wiring or maintenance. 2. Please keep the range hood clean. 3. To get the best performance, the vertical clearance between the cook- top and the range hood should range from 28” to 32”. (Fig.1) 28”-32” Fig.1 : Optimum range hood height Ducting method A. This range hood must be flued to external air space either through the roof (fig.2 ) or through the wall (fig.3) Fig. 2 Fig.
WARNING - To reduce the risk of fire, electric shock, or injury, observe the following: A. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. B. Before servicing or cleaning the unit, switch the power for service panel and lock panel, to prevent power from being switched on accidentally. When the service is disconnecting, it cannot be locked, fasten a prominent warning device, such as a tag, to the service panel. C.
WARNING- To reduce the risk of injury in the event of a range top grease fire, observe the following: A. SMOTHER FLAMES with a close- fitting lid, cookie sheet, or metal tray, then turn off the burner. Be careful to prevent burns. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. B. NEVER PICK UP A FLAMING PAN - You may be burned. C. DO NOT USE WATER including wet dishcloths or towels- a violent steam explosion will result. D. USE AN EXTINGUISHER ONLY IF: 1.
Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. Connect the electrical wires. - Connect three wires (black, white and green) to house wires and cap with wire connectors.
Installation and Maintenance must be carried out by qualified person only Body Mounting Fit the range hood body at the correct height , via the brackets to the mounting surface. (Refer Fig.4 for mounting screw measurements). Locate the hanging screw allowing a distance of 0.2 inch of the screw head to the wall. Chimney Ducting A. Use the Upper Mounting Bracket to adjust the duct to the required height (maximum 27-1/6”) B.
C. TOOLS AND MATERIALS REQUIRED ◆ One common screwdriver. ◆ Plier (for opening electrical knockout). ◆ Electrical wire and supplies to comply with local cords. ◆ Electrical power drill. D. REPLACEMENT LED LIGHT Note: Before replacing LED light ensure the unit is switched off, when you want to change the LED light, please always wear working gloves. (Fig.6) 1. Using suitable tool (small slotted screw driver) gently pry off the LED light set. 2. Taking off the wire connecter with LED light set. 3.
E. ACCESSORIES Spare Parts Contents Item Part Spare Parts Contents Description Spec. Q'ty Item Manual 1 Part Description Spec. Q'ty OPERATION RA-1430C Please read and save this guide through before using your range hood Store the guide away in a safe place so that you will know where it is when you want to refer to it 2 Round Collar 6" 7" 1 3 Duct CoverMounting Bracket 1 4 Screws Package MANUAL 1 Screws Ø4x32 6 Screws Ø4x8 Plastic Screws 1/4" 8 6 F.
I. USE AND CARE Note: Operate switches (Fig.7) ④ Switch 1 : LED Fan speed indicator. 3 - Low speed 1 - High speed ③ ② ① 8 Switch 2 : Speed switch (Three speed fan) Fig.7 Switch 3 : Light switch Switch 4 : Power switch and delay switch. Push once : Delayed shut off. Push twice : Immediate shut off. Note: Range hood should be turn on either before or the same time when cooking begins. After cooking, range hood should be kept on for about 3 more minutes for complete ventilation of cooking odor.
J. PARTS LAYOUT DIAGRAM 4 Model: RA-14 3 0C RA-1490C 6 5 8 1 7 2 10 9 11 15 13 3 12 14 1. Duct cover-Mounting bracket 2. Duct cover 10. Capacitor support 3. Plastic plate 11. LED driver 4. Hood-Mounting bracket 12. Capacitor 5. Rubber stand 13. Squirrel cage 6. Hood casing 14. Aluminum filter 7. LED Light 15. 6”/7” round collar 8. Control board 16. 9.
K. CIRCUIT DIAGRAM Fig.8 Details the internal electrical circuit of this range hood unit. Any faults with this unit should only be attended to by a qualified technician. White Yellow Orange Red Brown Black Yellow Capacitor Brown White Blue Gray Red Motor Yellow Brown White Blue Gray Red Motor Brown Black LED driver Black LED light Red Black Power White Ground Fig.
L. SPECIFICATIONS RA-1 430 C /RA-1490C Specifications Body Dimension (WxDxH) (W)29-3/4” 35- 3 /4" x ( D ) 24 - 1 / 8 " x ( H )12- 3 / 16 " Low- 630 ± 50 R.P.M. /High- 1670 ± 50 R.P.M. Revolutions Consumption - Motor 1 42 W Consumption - Lamp 1 W * 2 / 3.6 Vdc / 1500 maH Rotation Squirrel Cage Diameter Exhausting Duct 6" / 7" Round Outlets 120V / 60 Hz Voltage Appearance Treatment Brushed Stainless Steel * Specifications subject to change without prior notice. M.
Limited Warranty Windster Hoods Inc. warrants this product against defects in material or wo rkmanship as fol lows: 1) Labor: For a period o f one (1 ) year from the date o f purchase, if th is p roduct is determined to be defective, Windster wi ll repair or replace the product, at i ts option, at no charge. After the warranty period, you must pay for all labor charges. During the “ labor” war ranty period there wil l be no charge for labo r.
Defective Products: All products will be inspected, tested, and carefully packed by the manufacturer before shipping to customers. Products that are damaged during transit can only be exchanged for the same product, under the condition that the customer must get a RMA (Return Merchandise Authorization) from Windster. When products are received defective, you must notify us within the 3 business days of receiving the package. Replacement products are only shipped when the RMA is issued. NO EXCEPTIONS.
