Operating Instructions MODELS: T708 T716 T720 TP IPX4 230 VOLT ONLY 120 VOLT ONLY Read ALL instructions before using the machine .
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. WARNING DANGER: ! ! Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner’s Manual and on your machine.
! ! DANGER: Electrocution could occur if maintenance and repairs are performed on a unit that is not properly disconnected from the power source. Disconnect the power supply before attempting any maintenance or service. WARNING: Operating a machine without observing all labels, decals, etc., could result in injury or damage. Read all machine labels before attempting to operate the machine. Make sure all of the labels are attached or fastened to the machine.
THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors. EXTENSION CORDS: If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length. GROUNDING INSTRUCTIONS: This appliance must be grounded.
VACUUM AND ACCESSORIES A B C D E F G H I J K M N O P R Motor Block On/Off Switch Float: Keeps liquid out of Motor Block Polyester Filter: Remove for use with liquids Hooks: Secure Motor Block to Tank Suction Inlet Tank 2-pc. Chrome Wand 10-ft. x 1-1/2" Flexible Hose 2-pc PVC Wand Universal Adapter 3" Round Brush Crevice Tool 16" Brush 16" Squeegee Fixed Carpet Tool ATTENTION: The Polyester Filter must be cleaned after each use to maintain efficient suction.
OPERATION This machine is a commercial vacuum designed for wet and dry pick-up. L Dry soil can be vacuumed directly into the tank. To empty the tank of dry soil, remove the top and dump into trash receptacle. For wet pick-up, remove polyester filter. The machine is equipped with a float shut-off. As the tank is filled to capacity, a float rises and seals the vac intake, causing loss of vacuum. Switch off the vacuum when this happens and bring the machine to a floor drain.
PERIODIC MAINTENANCE (Every six to twelve months): 1. Check filter for wear, replace dirt saturated filters that do not respond to normal cleaning. 2. Inspect gasket seals and replace those which have begun to leak. 3. Replace both carbon brushes when either is less than 3/8" long. (PN S8TOEG845) 120V (PN S8TOGB839) 230V Examine carbon motor brushes and commutator. SERVICING THE FILTER The filter is accessed by lifting the head assembly off the tank.
SERVICING THE VAC MOTOR CARBON BRUSH REPLACEMENT 1. Disconnect power cord from power source. 2. To access the vac motor, remove the screws that attach the main cover to the head assembly and set the cover to one side. 3. Remove the motor cover by removing two screws. See Figure 1 4. Remove the wire terminal from carbon brush housing. See Figure 2 5. Remove the carbon brush assembly by removing the 2 screws that attach it to the vac motor. See Figure 3 6. Inspect armature commutator.
T708/T708IE VACUUM MOTOR ASSEMBLY No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. Part Num. S81122 S80117 S80138 S80139 S81006 S80450 S83733AUG6 S82627 S81006 S81054 S81054 S83734AUB.
T716/T720TP VACUUM MOTOR ASSEMBLY No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. Part Num. Description S81122 S80117 S80138 S80139 S81006 S81054 S86097AUG6 S81979 S81054 S81005 S80490 S81006 S86070AUB.
T716 TANK ASSEMBLY No. Part Num. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. S82558V S82637 S82016 S82584AG6 S82846 S82593 S82652AG6 S81300 S81847G6 S81050 S83883 S81072 S81860 S81302 S82559 S82680 S82556 S80904 S82557 Handle Tank – 400 Screw, M5x30 Retainer, Tank Gasket Deflector, Tank Adapter Rivet, 5 x 24.5 Clamp Screw, M8 x 15 Plastic Washer Support, Handle Support Rivet, M5 x 19 Wheel Caster Screw, M8 x 15 Support, Axle Wheel Cap, End Qty. No. Part Num.
T720TP TANK ASSEMBLY No. Part Num. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. S82048 S81026 S83883 S83028 S82970 S82969 S81847G6 S81300 S82652AG6 S82593 S82846 Tank – 400 Screw, M5 x 30 Plastic Washer Hook, Latch Release Swivel Release Knob Clamp Rivet Hose Adapter Deflector, Tank Gasket Qty. No. Part Num. Description 1 4 4 1 2 2 2 4 1 1 1 12. 13. 14. 15. S82586AG6 S81050 S82594BL T9007 Retainer, Tank Adapter Screw, M5 x 35 Push Button, Two-Piece, Blue Label, Titan T720TP CART No.
TSQ16 FRONT-MOUNTED SQUEEGEE No. Part Num. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 2.–12. BD705205 BD715508 BD735608 BD735607 BD735611 BD735609 BD735602 BD735601 BD715509 BD735604 BD735605 BD735603 BD735612 BD735609 BD705201 BD705203 BD705202 BD705200 Qty. Hose Assembly 1 Housing 1 Bolt, Guide Wheel, 1/4-20 x 1.75"L.
LABELS T9008 T9007 Windsor Titan Logo ACCESSORIES TSQ16 TSQ20 S72741 S82860 S82845 S82852* S76061* S82995* S82881 S82855 Front Mounted Squeegee Front Mounted Squeegee Paper Bag Filter Bag, Standard for 708 Model Filter Bag, Standard for T716 and T720TP Filter Cartridge, Paper, Optional for T716 and T720TP Filter Cartridge, Washable Paper, Optional for T716 and T720TP Filter Cartridge, HEPA Equivalent, Optional for T716 and T720TP Filter Cartridge, HEPA Equivalent, Optional for T708 Cartridge Filter Ret
