Operating Instructions (ENG) FLOOR POLISHER MODELS: SP13 10090220 SP17X 10090280 SP15 10090230 SP20X 10090320 SP17 10090240 SPDS20 10090350 SP20 10090310 Read these instructions before using the machine. G 86221940 12/29/06 PRV NO.
MACHINE DATA LOG/OVERVIEW MODEL______________________________ DATE OF PURCHASE ________________ SERIAL NUMBER____________________ YOUR DEALER Name: __________________________________________________________________________________________________ Address: _______________________________________________________________________________________________ For the name and address of your dealer contact: Windsor Industries Phone Number: __________________________________________________________________________
TABLE OF CONTENTS Machine Data Log/Overview.........................2 Table of Contents..........................................3 HOW TO USE THIS MANUAL How to use this Manual.................................4 SAFETY Important Safety Instructions ........................1-1 Hazard Intensity Level. .................................1-2 Grounding Instructions..................................1-3 OPERATION / MAINTENANCE Technical Specifications ...............................2-1 Handle Installation ........
HOW TO USE THIS MANUAL This manual contains the following sections: - - HOW TO USE THIS MANUAL SAFETY OPERATIONS MAINTENANCE PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized Windsor dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine.
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. ! WARNING: To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer’s recommended components and attachments.
HAZARD INTENSITY LEVEL The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: ! WARNING WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
GROUNDING INSTRUCTIONS THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a one 15 amp nominal 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors. GROUNDING INSTRUCTIONS: This appliance must be grounded.
TECHNICAL SPECIFICATIONS ITEM Construction DIMENSION/CAPACITY Heavy-duty die cast aluminum deck with heavy-duty rubber bumper, tubular steel adjustable handle with die cast aluminum handle housing Motor SP13, SP15, SP17, SP20 SP17X, SP20X, SPDS20 Brush/Pad speed SP13, SP15, SP17, SP20, SP17X, SP20X SPDS20 Electrical system Cable Switches Wheels Handle Dimensions (L x W x H) 13” (33 cm) model 15” (38 cm) model 17” (43 cm) model 20” (51 cm) model 2-1 1.0 hp 1.
HANDLE INSTALLATION WHEN INSTALLING THE HANDLE ASSEMBLY, CHECK ORIENTATION OF THE CORD ASM AND CORD HOOK. HANDLE RECEPTACLE 4 5 6 MOTOR PLUG DECK ASSEMBLY PIVOT HOLE 3 2 1 SEE NOTE This must be installed by qualified personnel. Read all instructions thoroughly. The machine is shipped with handle unassembled. The machine is shipped with handle unassembled. Follow these steps for installation: 1. Remove handle and deck assembly from carton. 2.
OPERATION CONTROLS 1. Safety Lock – Prevents unintended operation of the machine. 2. Switch Levers – Turns machine on/off. 3. Adjustment Handle – Allows the handle to be adjusted to a comfortable operating position. 1 1. To adjust handle lock, tighten nut on handle while in the locked position. Optimum locking force and ease of locking is accomplished when the locking lever nut is set to a torque of 30 to 50 inch pounds in the locked position. 2.
OPERATION ! CAUTION DAILY MAINTENANCE For indoor use only. To prevent possible damage to the floor when using the brush option, use water or other approved cleaning solution while operating. When using the pad option, always keep the machine moving when in contact with the floor. ! WARNING High starting torque. Hold machine firmly with both hands. 1. Ensure that the pad driver or brush is installed correctly and in good shape. Install or change pad if necessary. 1. Inspect power cord for wear.
MAINTENANCE SCRUB BRUSHES NOTE: All original equipment brushes are equipped with “Perform Alert©”. This feature will tell the operator when it is time to replace the scrub brushes. “Perform Alert©” brushes have pretrimmed bright yellow tufts to indicate the length of a worn out brush. When the tufts in the scrub brush wear to a length equal to the yellow tufts, the scrub brushes should be replaced.
TROUBLESHOOTING PROBLEM Machine will not run Electrical shock Repeated circuit breaker tripping Excessive vibration Pad does not turn but motor is running CAUSE SOLUTION Circuit breaker tripped in building. Check and reset. Power switch failure. Test switch for continuity and replace if necessary. Tripped circuit breaker. Reset. Faulty power cord. Replace. Fuse in motor is blown. Replace. CAUTION: To reduce the risk of electrical shock, unplug the machine before opening fuse holder.
BRUSH/PAD DRIVER GROUP 3 3 1A 1B 1C 1D 3-1 STORM POLISHER 86221940 12/29/06 2A-W
BRUSH/PAD DRIVER GROUP REF PART NO. PRV NO.
FRAME GROUP 20 1 21 22 23 2 19 3 18A 18B 18C 18D 4 5 6 7 8 9 MOTOR ASM SEE PG 3-5 17A 17B 17C 17D 3-3 8 14 15 16 11 12 13 STORM POLISHER 86221910 12/29/06 10
FRAME GROUP REF PART NO. PRV NO.
MOTOR GROUP 6 2 4 4 1 1 5 3 12 12 11 11 SP17X, SP20X 10090280, 10090320 SP13, SP15, SP17, SP20 10090220, 10090230, 10090240, 10090310 10 7 8 9 12 11 SPDS20 10090350 3-5 STORM POLISHER 86221940 12/29/06
MOTOR GROUP REF PART NO. PRV NO. QTY DESCRIPTION 1 2 3 4 86217490 86220020 86222090 86223690 27884 500763 53263 70702 1 1 1 3 COVER, MOTOR LABEL, STORM MAIN MOTOR, 1 HP 115V INDUCTION SCR, M5 X .8 X 15MM BLK 5 86222100 53264 1 MOTOR, 1.5 HP 115V INDUCTION 6 7 8 86220030 86217500 86223680 500764 27892 70700 1 1 8 9 86222070 53253 1 10 86220040 500765 1 11 12 86223700 86223030 70723 62917 6 1 LABEL, STORM DELUXE MAIN COVER, ASM, MOTOR SCR, M5 X .8 X 10MM PHMS BLK MOTOR, 115V 1.
HANDLE GROUP 14 13 5 6 17 2 16 22 18 1 9 11 20 3 12 7 19 9 15 21 8 4 10 3-7 STORM POLISHER 86221940 12/29/06
HANDLE GROUP REF PART NO. PRV NO.
WIRING GROUP PRIOR TO SN * 5 10 9 7 4 12 8 11 6 1 3 6 11 2 3-9 STORM POLISHER 86221940 12/29/06
WIRING GROUP REF PART NO. PRV NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 86233170 86234150 86216920 86247920 86136780 86288450 86007110 86224550 86224750 86137290 86137330 86215140 20054 23167 23206 57069 70801 70689 72123 73989 73993 87057 87208 140674 1 1 1 1 2 2 2 1 1 2 2 1 CLAMP, 3/8 NYLON UL/CSA CORD SET, 14/3 STO X 50' YLW CORDSET, 14/3 X 52”SJT, BLK NUT, ORG WIRE (2-5 18G/2-14G) SCR, M3.5 X 40 PHTF TYPE B SCR, M4.
WIRING DIAGRAM / SPARE PARTS SUGGESTED SPARE PARTS PART NO. PRV NO. 86225710 86224740 86224750 86007110 86215130 86222560 86223550 86003660 86003670 86135540 86223390 86216700 86216710 87202 73990 73993 72123 14344 66334 67430 34378 34379 27352 67488 140401 140411 3-11 DESCRIPTION SERIAL NO. FROM WASHER, BEARING (HANDLE ADJ) SPRING, EXT .5 OD X 3.5L SPRING, COMP .48 OD X .91 L SWITCH.
