Industries Carpet Cleaner User Manual
SPIRIT
1.
Fill
the
solution
tank.
2.
Move
machine
to
the
cleaning
area.
3.
Lower
the
brush
housing
to
the
floor.
4.
Adjust
the
brush
to
the
desired
height.
5.
Plug
machine
into
electrical
outlet.
6.
Release
handle
by
pressing
bar
with
foot.
Push
handle
forward
to
lock.
To
release
handle:
A.
Press
down
with
foot.
6.
Pull
back
on
handle.
7.
Press
Vac/Pump
switch
with
foot
to
turn
on.
8.
Tilt
the
machine
back
on
rear
wheels
until
brush
is
off
the
floor.
Press
brush
switch
with
foot
to
turn
on.
NOTE: Starting the machine with dry brush rest-
ing on floor may trip the brush motor circuit
breaker.
9.
Squeeze
the
solution
control
lever
to
dispense
cleaning
solution.
10.
Pull
the
machine
backwards
at
a
steady
pace.
Different
carpet
conditions
will
determine
the
speed
required,
approximately
25
to
30
feet
per
minute
(8-9
m).
Do
not
press
down
on
the
handle
while
cleaning,
this
will
cause
the
brush
housing
to
raise
slightly
and
reduce
efficiency.
11.
Release
the
solution
lever
about
12”
inches
(150
cm)
before
the
end
of
each
pass
to
ensure
all
solution
is
picked
up.
12.
Allow
each
cleaning
pass
to
overlap
the
previous
pass
about
2”
inches
13.)
cleaning
check
for
foam
build-up
in
re-
covery
tank.
hen
excessive
foam
begins
to
build
up,
add
a
defoaming
compound
to
the
recovery
tank
according
to
the
Instructions
on
the
manufacturer’s
package.
Foam
build-up
depends
on
the
type
of
cleaning
concentrate,
and
residue
remaining
carpet.
An overflow of foam from in the recovery tank
into the vacuum intake can damage the vacuum-
motor. Always be aware of the waste water level
and foam in the recovery tank, es ecially when
using an accessory tool. BEFOR
E
foam or
solu-
tion is pulled into vac intake empty the recovery
tank.
Never put defoaming compound in the solution
tank. Damage to pump will result.
NOTE:The vac motor is protected by a circuit
breaker which will only trip under conditions of
abuse, such as an overflow of foam into the
dome. When an overflow does occur the vac
motor must be allowed to dry thoroughly before
continuing work.
1.
Remove source of overflow.
2. Run motor to dry.
6
14.
When
solution
tank
empties
the
machine
will
start
streaking
and
won’t
completely
clean
the
floor.
Turn
both
switches
off,
empty
the
recovery
tank,
and
refill
the
solution
tank.
Use
the
clear
drain
hose
on
the
rear
of
the
solution
tank
as
a
sight
gage
to
determine
amount
of
fluid
in
tank.
15.
Ventilate
the
room
when
cleaning
has
been
completed.
Keep
all
traffic
off
the
floor
until
it
is
thoroughly
dry.
16.
When
done
cleaning
to
a
utility
sink
and
for
the
day
bring
the
machine
loor
drain.
Perform
the
daily
/regular
maintenance.
Set
the
recovery
tank
aside
so
solution
tank
will
dry.
When not using the machine put the brush in
the storage position. (see daily maintenance on
page 8) Leaving the brush on the floor for long pe-
riods of time may ruin It.
98353